Parts for Ge CDE06RP2NBS1: Doors & Drawers Parts

This reed switch and magnet assembly senses door open/close to tell the appliance when to turn lights on and control door-activated features. It replaces a failed door sensor to restore proper door detection. What it does:

• Acts as the door sensor: magnet closes the reed switch when the door is shut.
• Controls interior light and other door-activated functions by signaling open/closed status.
• Commonly replaces a faulty switch when lights stay on or won't turn on with the door.
• Helps stop false "door open" behavior that can affect cooling or dispenser operation.

• Disconnect power to the appliance before starting any work.
• Handle the switch and wiring gently; avoid pulling on wires or connectors.
• Mount the switch and magnet so the magnet aligns closely with the switch when the door is closed.
• After installation, restore power and verify the light and door-activated functions operate correctly.

This upper partition spring replaces the small tension spring that helps hold the refrigerator partition/support in place for stable shelf spacing and quiet operation. It restores the partition's secure positioning and reduces movement or rattling. What it does:

• Provides tension to secure the fridge upper partition or divider in its track
• Prevents the partition from slipping, sagging, or shifting during normal use
• Reduces rattling or vibration caused by a loose partition
• Restores proper alignment of the partition for consistent shelf spacing

• Disconnect power to the appliance before beginning any repair
• Remove food and any shelves/parts that block access to the partition area
• Note orientation before removal; spring installs under tension—use pliers as needed

This is the upper partition slide groove that supports and guides the refrigerator partition so it moves smoothly and stays aligned. Replacing a worn or broken groove restores secure support and proper partition movement. What it does:

• Guides and supports the upper partition so it slides in the cabinet track
• Keeps the partition aligned to prevent tilting or binding
• Prevents the partition from slipping out of its track
• Resolves symptoms like a loose, misaligned, or noisy partition during use

• One upper partition slide groove

• Disconnect power to the appliance before starting any work
• Remove the partition and nearby shelves per your model's service instructions to access the groove
• Inspect mating surfaces for damage or debris, then align and snap the new groove into place
• Reinstall partition and shelves, restore power, and verify smooth operation

This upper partition slide cover is a replacement plastic cover that protects and guides the refrigerator partition slide, helping shelves move smoothly and preventing wear or damage to the slide mechanism. What it does:

• Covers the upper partition slide to reduce friction and protect the slide from damage
• Helps keep the shelf aligned and prevents binding when sliding shelves in and out
• Stops metal-on-metal contact that can cause noise or wear
• Commonly replaced when cracked, broken, or allowing shelf misalignment or rattling

• One upper partition slide cover

• High-level replacement—typically snaps into existing mounting tabs; inspect tabs for damage before installation
• Remove the shelf or partition as needed for access; handle plastic parts gently to avoid cracking
• No special tools usually required; use a flat tool to gently release retaining clips if needed
• For work near electrical components or lights, unplug the appliance or switch power off to be safe

This cable clamp secures an appliance's wiring where it passes through a cabinet or chassis, protecting wires from chafing and reducing strain on connectors for safer, more reliable power and signal routing. What it does:

• Holds and routes power or signal wires to prevent rubbing and insulation wear
• Reduces strain on connectors to help prevent intermittent connections or shorts
• Keeps wiring clear of moving parts and hot components
• Helps maintain a tidy, serviceable harness layout for easier repairs

• Disconnect power (unplug or shut off breaker) before starting any repair.
• Replace the clamp where the harness passes through the cabinet or chassis, seating the clamp so it fully surrounds the wiring.
• Do not overtighten or excessively pinch the wiring; secure just enough to prevent movement.
• If wiring shows fraying or damaged insulation, replace the harness or repair wires per OEM guidelines before reinstalling the clamp.

The Control Board is an OEM replacement part for GE refrigerators. It is responsible for managing and displaying the various functions and settings of your refrigerator. 

A bad display control board can occur due to electrical issues, component failure, or damage to the board itself. If you notice symptoms such as a blank or flickering display, unresponsive buttons, or incorrect temperature readings, it may indicate a need to replace the control board.

Symptoms of a bad display control board include:

• Blank or flickering display
• Unresponsive buttons
• Incorrect temperature readings

Restore your refrigerator by replacing the faulty display control board with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The Fastener Door Handle is an OEM component for GE refrigerators. This door handle provides a comfortable grip for accessing refrigerator shelves and bins. It attaches securely to the refrigerator door through durable metal fasteners. 

Causes for a bad door handle could be cracks, damage, or stripped fastener holes resulting in a loose or detached handle. Regularly gripping and lifting may also cause normal wear over time.

Symptoms of a failing door handle include:

• The handle detaching completely from the door  
• Looseness making the handle wobbly or unstable to hold
• Sharp edges or broken parts posing a safety risk

This OEM GE handle is also compatible with Hotpoint, RCA, and select Kenmore refrigerator models.