Parts for Electrolux FGEF302TPBA: 05 - Doors Parts

This high-temperature insulation is used in the oven assembly to contain heat and protect nearby components and cabinetry. Replacing damaged insulation helps the appliance maintain set temperatures and keeps exterior surfaces from getting excessively hot. What it does:

• Helps retain heat for stable baking and roasting temperatures
• Reduces heat transfer to the appliance frame and adjacent cabinets
• Replaces insulation that is torn, charred, or saturated with spills/grease

• One insulation piece

• Disconnect power; for gas models, also shut off the gas supply
• Remove the range or wall oven and access the oven body
• Wear gloves, eye protection, long sleeves, and a dust mask; fibers can irritate skin and lungs
• Reinstall in the same orientation/routing as the original; do not compress insulation or block vents

This interior cabinet liner replaces a damaged or cracked refrigerator cabinet panel to restore a clean, sealed interior surface and proper mounting for shelves or components. It helps maintain interior hygiene and prevents airflow leaks. What it does

• Provides the finished interior surface for the refrigerator cabinet and supports shelf and accessory mounting.
• Covers and protects insulation and internal cavity areas from spills, stains, and physical damage.
• Helps maintain proper airflow paths and compartment sealing to support cooling performance.
• Commonly replaced when the liner is cracked, warped, damaged by impact, or permanently stained.

• One interior cabinet liner panel as shown.

• Liners may require panel clips, screws, or adhesive (verify retained fasteners).
• Disconnect power and empty the compartment before starting to avoid injury or damage.
• Handle carefully to avoid cracking or scratching the replacement liner during installation.
• Reuse or replace any trim, clips, or fasteners only if they are present and in good condition.

This is a replacement mounting screw used to secure panels and components in compatible Frigidaire appliances. It restores proper fit and helps prevent rattles, loose panels, and parts that shift during operation. What it does:

• Fastens trim, panels, brackets, or controls to the appliance frame
• Restores secure attachment to reduce vibration, noise, and movement
• Replaces stripped, missing, or corroded screws that prevent proper assembly
• Works wherever the OEM screw with this part number is specified

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not overtighten to avoid stripping threads or damaging parts
• Keep removed hardware organized and compare parts to the old screw for correct fit

This spacer positions and cushions refrigerator components to prevent contact and reduce vibration, helping panels and assemblies align correctly for reliable operation. Lightweight and simple to install, it restores proper fit where the original spacer is damaged or missing. What it does:

• Keeps panels, trim, or internal components spaced correctly to maintain alignment
• Absorbs minor vibration and prevents metal-to-metal contact that can cause noise
• Helps preserve seals and door alignment by maintaining correct component clearance
• Common symptom: loose trim, rubbing panels, rattling, or visible gap where a spacer is missing

• One spacer

• Disconnect power to the appliance before beginning any work
• Remove adjacent panels or trim as needed to access the spacer; retain fasteners for reassembly
• Inspect surrounding clips or mounting points and replace any damaged hardware

This replacement door hinge restores smooth pivoting and proper alignment so the appliance door opens and closes correctly. It helps stop sagging, misalignment, rubbing and uneven sealing. What it does

• Provides the pivot point that lets the door swing open and closed.
• Replaces a worn, bent or broken hinge causing a sagging or drooping door.
• Helps restore a tight door seal to prevent cool-air loss and uneven temperatures.
• Eliminates clicking, binding or scraping noises caused by a damaged hinge.

• Support the door before removing the old hinge to prevent dropping or damage.
• Use basic hand tools; keep fasteners and any spacers for reassembly.
• Check door alignment and seal after installation; adjust hinge position as needed.

A small mounting spacer used to position and support appliance components for correct alignment and stable operation. Replaces a worn or missing spacer to help restore proper fit between panels and parts. What it does:

• Keeps panels, brackets, or components spaced correctly to prevent rubbing and misalignment
• Helps reduce vibration and rattling caused by gaps or loose fits
• Restores correct clearance for moving parts that need precise spacing
• Used wherever a fixed gap or support is required between parts

• Disconnect power (and fuel or water if applicable) before beginning any repair
• Access may require removing outer panels, trim, or adjoining components
• Keep orientation and placement the same as the original spacer; install snugly but avoid over-tightening
• If other parts show wear or damage, inspect and replace them as needed for a complete repair

This support bracket secures and stabilizes appliance components, restoring proper alignment and stopping movement. It's a simple replacement that helps reduce rattling and prevents panels or assemblies from shifting during use. What it does:

• Provides a rigid mounting point to hold panels, trim, or internal assemblies in place
• Restores proper alignment when a worn or broken bracket causes gaps or looseness
• Reduces vibration and rattling caused by a damaged or missing support
• Keeps connected parts from shifting, which can prevent further wear or damage

• Disconnect power to the appliance before beginning any repair
• Verify the bracket orientation and fit against the mating surface before fastening
• Use the factory screw locations and hardware; tighten screws securely but avoid over-torquing

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

This spacer sets the correct gap between mating parts in your appliance's assembly, preventing rubbing and misalignment. Replace a missing or worn spacer to restore a solid fit, reduce noise, and protect surrounding components.

• Maintains proper spacing between components for correct alignment and operation
• Reduces metal-to-metal contact, squeaks, and premature wear
• Helps fasteners and panels seat securely
• Typical symptoms when failed: loose or rattling parts, uneven gaps, or visible wear marks

• Disconnect power; for gas models, shut off the gas. Allow the appliance to cool completely.
• Access the assembly per your model's diagram; note the original orientation/stack-up before removal.
• Reuse original fasteners if serviceable; hand-start threads and tighten snugly to avoid damaging the spacer.
• Verify alignment and clearances before fully reassembling. Quantity and location vary by model.

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts