Parts for Frigidaire FFTR1425VW: Doors Parts

The Gasket is an OEM part for Frigidaire refrigerators. As a component of the refrigerator door, the gasket provides an important insulation barrier, sealing in cold air and keeping warmer air out. It works to maintain consistent temperatures within the refrigerator compartment. 

Causes of a bad gasket can include cracks or breaks due to aging and repeated opening and closing of the door. Gaskets can also become compressed or misshapen over time, reducing their effectiveness.

Symptoms of a bad gasket include:
 

• Increased humidity or moisture buildup inside the refrigerator  
• Frost or condensation appearing around the doors and inside walls
• Higher power bills due to the refrigerator having to work harder to maintain temperatures
• Warm air leaking in and causing temperature fluctuations inside the fridge

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

This replacement gasket restores a tight seal between mating parts in your appliance. Replacing a worn seal helps stop leaks and keeps performance steady by maintaining proper containment during normal operation.

• Creates a compressible barrier between components to prevent leaks and seepage
• Maintains proper system performance by preserving the intended seal
• Helps reduce vibration and wear at the joint
• Replace if cracked, flattened, brittle, warped, or if leaks are present around the connection

• Disconnect power; shut off water or gas if applicable
• Allow the unit to cool and relieve any pressure before service
• Clean and dry mating surfaces; remove the old gasket and residue
• Install without stretching; tighten fasteners evenly; do not use sealants unless specified by the manufacturer

This replacement name plate is the identification label used on the appliance's exterior to restore a clear, readable ID and finish. It helps keep the appliance looking complete and makes model/serial information visible. What it does:

• Replaces a worn, faded, or missing identification label on the appliance exterior
• Restores the appliance's original appearance and readable markings
• Helps owners locate model/serial details when present on the label
• Prevents confusion caused by missing or damaged name plate graphics

• High-level replacement; clean and dry the mounting surface before installing for best adhesion
• Remove any old adhesive or backing carefully to avoid surface damage
• Align the label precisely, then press firmly to secure
• Disconnect power and follow basic safety precautions when removing exterior panels if required

This replacement crisper bin restores storage space in your refrigerator by holding fruits and vegetables securely in the fresh-food compartment. Durable, easy-to-clean plastic keeps produce contained and organized. What it does

• Holds fruits, vegetables and other fresh-food items to prevent rolling or shifting
• Protects produce from spills and helps keep the fresh-food compartment organized
• Clear plastic lets you quickly see contents without removing the bin
• Works as a direct-fit replacement for a worn, cracked or missing crisper bin

• One refrigerator crisper bin

• Slide into the crisper opening until it seats; it aligns with the cabinet rails or support ledges
• No tools typically required; remove nearby shelves or drawers first if needed for clearance
• Handle with care—avoid dropping to prevent cracks or chips
• Disconnect power only if removing other components that require access to electrical parts

This bearing supports and helps the dryer drum rotate smoothly, reducing noise and wear for reliable load tumbling. Replace a worn bearing to restore quieter, more even drum movement. What it does:

• Supports the dryer drum on the rear/front shaft so it spins freely
• Reduces metal-on-metal contact that causes squeaks, grinding or rumbling
• Helps maintain proper drum alignment to prevent uneven wear and laundry snags
• Restores smoother rotation when old bearings show play or roughness

• One bearing as shown

• Disconnect power (and gas, if applicable) before starting any repair
• Access may require removing the dryer front or rear panel and drum — your model's service instructions
• Inspect mating shaft and housing for wear; replace or repair damaged components to avoid premature failure

The Hook is an OEM part for Frigidaire refrigerators. It helps to ensure a secure and proper closure of the refrigerator door.

A bad hook can be caused by wear and tear, damage, or misalignment. Signs of a faulty door closer hook include the door not closing fully or not staying closed, difficulty in opening or closing the door smoothly, or a loose or wobbly door.

Symptoms of a bad hook can include:

• The refrigerator door not sealing properly
• Excessive force required to open or close the door
• Visible damage or misalignment of the door closer hook

Replace your worn or damaged hook with this genuine OEM part to restore your refrigerator door. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This is a replacement threaded screw used to secure appliance components where the original fastener is missing or damaged. It restores proper attachment so panels, brackets, or small parts stay in place. What it does:

• Secures panels, brackets, or trim to the appliance to prevent movement or rattling
• Replaces missing, stripped, or damaged screws that can allow parts to come loose
• Helps restore proper alignment of parts when used in original mounting locations
• Suitable as a direct-fit replacement when the OEM part number matches

• Disconnect power before working on any appliance and follow all safety precautions
• Use the correct driver or bit to avoid stripping the screw head
• Keep small parts away from children and pets; magnetic trays help during installation