Parts for Ge PFSS2MIYCSS: 01 - Doors Parts

The water filter is an OEM part for GE refrigerators. This filter removes or reduces various contaminants.

Features and Benefits:

• Easy DIY replacement, typically mounted inside the refrigerator at the back of the compartment.
• Removes or reduces various contaminants in your water and ice, including lead, cysts, asbestos, atrazine, , taste and odor, chlorine, sediment, turbidity, and more
• NSF/ANSI 42 and 53 standards
• 6 Month lifespan filter
• Carbon Block media
• Micron rating: 0.5-1 micron (Class I)

When to replace your filter:

• Bad taste or odor in water and ice
• Cloudy or discolored ice
• Reduced water flow or pressure
• Refrigerator replace filter indicator light is on

Note: If replacing the Culligan metal canister design filter for the first time, a special adapter, part number AP2615702 is needed, which is not included with this part. The compatible bypass cap is part number AP6891551.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

A short 8-32 x 3/8 hex washer head screw used to secure small appliance panels and components. Simple replacement for stripped or missing fasteners to restore proper fit and prevent rattles or loose parts. What it does:

• Secures panels, brackets, and small assemblies in place
• Helps eliminate vibration-related noise from loose parts
• Replaces missing, damaged, or corroded screws to restore proper alignment
• Fits standard 8-32 threaded holes requiring a 3/8" length screw

• One 8-32 x 3/8 hex washer head screw

• Use the correct 8-32 driver to avoid stripping the head
• Tighten snugly but avoid over-torquing to prevent thread damage
• Disconnect power and follow appliance safety procedures before accessing internal components
• Replace only like-for-like fasteners in load-bearing or safety-critical locations

This bracket support is a small mounting bracket that secures and stabilizes appliance components, helping keep panels and assemblies aligned for proper operation and reduced vibration. It's a direct-fit replacement when the original bracket is broken or missing. What it does

• Provides a sturdy mounting point to hold panels or internal components in place
• Restores proper alignment to doors, panels or assemblies that sit on the bracket
• Reduces rattling or vibration caused by a loose or damaged bracket
• Helps prevent wear or damage from parts shifting during use

• Unplug the appliance and shut off water/gas (if applicable) before starting work
• Use the original mounting screws; replace damaged fasteners as needed
• Handle sharp sheet-metal edges carefully and wear gloves and eye protection

This is a 1/4-20 UNC machine screw used to fasten appliance components securely. It restores proper fit and stability where threaded fasteners are required, preventing loose panels or shifting parts. What it does:

• Secures panels, brackets, or assemblies that use a 1/4-20 UNC threaded hole
• Stops rattling or movement caused by a missing or damaged screw
• Restores correct mechanical connection for safe operation
• Useful when replacing stripped, corroded, or lost fasteners

• Disconnect power to the appliance before servicing.
• Start threads by hand to avoid cross-threading; tighten until snug.
• Do not overtighten — use appropriate torque for the material to avoid stripping threads or damaging parts.
• Ensure proper contact and secure fastening.

This door gasket creates an airtight seal around the perimeter of the refrigerator or freezer door. Replacing a worn seal helps maintain stable temperatures, reduce frost and moisture, and improve efficiency and food preservation.

• Seals the door opening to prevent warm air leaks and cold air loss
• Helps maintain proper temperatures in the fresh food or freezer section
• Reduces frost buildup and condensation around the door
• Replaces gaskets that are cracked, warped, torn, or won't lay flat
• Symptoms include visible gaps, moisture on or around the gasket, frequent frost, or longer run times

• Disconnect power and clear items from the door for easier access
• Warm the new gasket with a hair dryer on low or soak in warm water to relax folds
• Remove the old gasket from the retainer; press the new gasket fully into the channel, starting at the top corners and working around
• Check door alignment and sealing all around; adjust hinges if needed and perform a dollar-bill test

This OEM fastener secures interior components and trim on compatible appliances to restore proper fit and reduce movement. It's a direct-replacement hardware piece used where the original mounting screw or retainer is lost or worn. What it does

• Secures panels, trim pieces, brackets or small assemblies to the appliance frame
• Restores firm attachment to reduce rattles, gaps or misalignment
• Replaces missing or stripped hardware that prevents proper part installation
• Helps maintain proper operation by keeping service parts seated and stable

• Disconnect power or unplug the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or driver bit to avoid stripping the head
• Hand-start the fastener, then tighten snugly—do not over-torque
• Replace any additional damaged fasteners with the same OEM part for best fit

This replacement screw fastens refrigerator components securely, restoring a tight, rattle-free fit when original hardware is missing, stripped, or corroded. Use it to secure panels, brackets, or trim and keep parts properly aligned.

• Secures panels, brackets, covers, or trim in place
• Helps maintain correct alignment of components and hardware
• Reduces vibration and rattling caused by loose or missing screws
• Replaces lost, rusted, or stripped screws

• Unplug the refrigerator and turn off water supply if working near water components
• Match thread and length to the removed fastener; hand-start threads to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin sheet metal
• Keep track of any spacers or washers reused from the original assembly

A replacement lower right bracket that secures and supports the lower section of the assembly for proper alignment and stable operation. Restores the original mounting point to reduce sagging and movement. What it does:

• Provides a secure mounting point for the appliance's lower assembly so panels, doors or components stay aligned
• Helps prevent sagging, rattling or uneven gaps caused by a damaged or missing bracket
• Maintains correct part-to-frame spacing so connected components operate smoothly
• Fits into the OEM mounting locations and matches factory attachment points

• Disconnect power to the appliance before attempting any repair to avoid shock or injury
• Requires basic hand tools; keep fasteners from the original bracket for reinstallation unless replacements are provided
• Hand-tighten fasteners, then snug to manufacturer torque recommendations—do not overtighten to avoid stripping

This replacement screw secures appliance brackets, panels, and components. It restores a tight, aligned fit when the original hardware is stripped, rusted, or missing, helping reduce vibration and rattling for reliable operation.

• Fastens brackets, panels, or mounts to keep components secure and aligned
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration, rattling, or loose/misaligned parts
• Matches original spec for reliable hold and fit

• Disconnect power before servicing; use proper PPE
• Match thread and length to the removed screw before installation
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Ensure parts are aligned and seating surfaces are clean before tightening

2 Per Kit

2 Per Kit

The Lower Freezer Basket is an OEM replacement part for GE refrigerators designed to fit in the lower section of the freezer, providing a convenient storage area for your frozen items.

A bad lower freezer basket can occur due to regular wear and tear or damage from mishandling. If you notice symptoms such as cracks, broken parts, or difficulty in sliding the basket in and out, it may indicate a need to replace the basket.

Symptoms of a bad lower freezer basket include:

• Cracked or broken basket
• Difficulty in sliding the basket in and out
• Uneven or limited storage space

Restore your refrigerator's freezer section by replacing the faulty lower freezer basket with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The French Door Gasket is an OEM replacement part for GE refrigerators. This gasket is designed to seal the gap between the French doors and the refrigerator's main body. It helps to keep cold air inside and warm air outside. The gasket also helps block out warm ambient air and keep temperatures stable inside.

Symptoms of a failed gasket include:

• Condensation or frost build-up along the door frame  
• Warmer than normal interior temperatures in the fridge section
• Higher power bills due to lost cooling efficiency
• Rush of warm air into the fridge when opening the door

Causes of gasket failure can be breakdowns of the seal from continuous opening and closing of the door over time. Sagging, cracks, or splits from aging are also common issues. 

It is also compatible with some Kenmore, RCA, and Hotpoint models.

This handle assembly replaces a damaged or worn refrigerator fresh-food door handle to restore a secure grip and straight door appearance. It provides a factory-fit replacement that mounts where the original handle attaches. What it does:

• Replaces a cracked, loose or broken fresh-food door handle
• Restores a safe, comfortable grip for opening the refrigerator door
• Corrects misaligned or crooked handle appearance
• Helps the door latch and seal operate normally by providing proper handle support

• One handle assembly as shown

• Unplug the appliance or disconnect power before beginning any repair
• Keep original fasteners; install with the same screws or clips provided and tighten snugly — do not overtighten
• Handle with care to avoid scratching the door finish; wear gloves to protect hands from sharp edges

This stop door is the replacement dispenser door that covers the ice/water chute and helps control dispensing. It restores proper closure to prevent drips and ice spillover and keeps the dispenser area sealed when idle. What it does

• Replaces the dispenser stop/cover to block the chute when not in use
• Helps prevent water drips and ice from falling into the dispenser well
• Restores a tight closure to reduce cold air loss from the cabinet
• Can resolve symptoms like a stuck or broken dispenser door or visible gaps at the chute

• One stop door

• Disconnect power to the appliance before beginning any service
• Usually installs with a few screws or snap clips; basic hand tools typically required
• Inspect surrounding trim and actuator parts for wear while replacing the door

This module snugger is a small retaining piece used in the refrigerator to hold its associated module or component securely in place. Replacing a cracked or missing snugger restores a tight fit, reduces vibration and noise, and supports correct operation.

• Secures the related module or assembly to prevent shifting
• Helps maintain proper alignment for reliable performance
• Reduces rattles and wear from vibration or movement
• Typical signs it's needed: part is broken or missing, components feel loose, or you hear rattling

• Disconnect power to the refrigerator before servicing
• Note the original orientation and location; take a photo for reference
• Reuse existing fasteners or clips if applicable; avoid overtightening
• After installation, confirm the part holds the assembly firmly and that movement is smooth where intended

This right-hand cam closure is a direct-fit replacement that helps the refrigerator door close and stay aligned for a proper seal. It restores smooth hinge movement and reliable door latching to reduce gaps and cold loss. What it does:

• Guides and secures the door as the hinge rotates to help the door latch fully
• Maintains door alignment to support an even seal and consistent cooling
• Reduces hinge noise and sticking when worn or damaged
• Common symptom: door won't stay closed, rubs, or leaves an uneven gap

• Disconnect power to the appliance before starting any repair
• Support or remove the door per the manufacturer's service instructions to access the hinge/cam
• Replace the cam and reassemble hardware; verify door alignment and operation after installation

This replacement dairy door restores a sealed compartment on the fridge door to keep butter, cheese and small items contained and organized. It replaces a cracked, broken or missing dairy door to improve closure and appearance. What it does:

• Provides a covered compartment on the inner door to keep small dairy items organized and contained
• Replaces cracked, broken or warped dairy doors that no longer latch or sit flush
• Helps reduce shifting and spills on the door shelf
• Restores proper fit and appearance to the refrigerator door interior

• One dairy door assembly

• Remove items from the door bin and lift or unclip the old dairy door per your model's instructions
• Align the replacement door with the hinge/slots and snap into place until it seats securely
• Inspect for proper closure and latch engagement before returning contents
• Use gloves to protect hands from sharp edges; unplug or disconnect power only if recommended by your model's service manual

This shelf module assembly restores a sturdy, level storage surface inside your refrigerator. Replace a damaged or missing shelf to recover usable space and keep items organized and easy to access. What it does

• Provides a flat, stable surface to support food containers in the refrigerator compartment
• Restores storage capacity when the original shelf is broken, warped, or missing
• Helps keep contents organized and accessible
• Addresses issues like sagging, instability, or a shelf that won't stay seated in its rails

• One shelf module assembly

• Disconnect power to the refrigerator before servicing
• Remove items from the area and slide/lift out the old shelf
• Transfer any reusable trims or components from the old shelf
• Fully seat the new shelf in the side rails; ensure it's level and secure before reloading

This 8-18 x 9/16 screw is a short sheet-metal fastener used to secure panels, trim and small components on appliances. It replaces missing or stripped screws to restore proper fit and reduce noise from loose parts. What it does

• Secures appliance panels, brackets and trim to prevent movement and rattling
• Holds small components in correct alignment for reliable operation
• Replaces lost, worn or stripped screws that cause gaps or loose fittings
• Common symptom link: fixes rattling panels, loose trim, or parts that shift during use

• One 8-18 x 9/16 screw

• Use the correct 8-18 driver bit and hand or low-torque power driver to avoid stripping
• Do not overtighten; snug until secure to prevent thread damage or panel deformation
• Turn power off/unplug appliance when installing near electrical components
• Keep extra screws on hand—hardware often comes in single quantities

The Set Screw is an OEM part for GE refrigerators. It is used to secure various components within the refrigerator, ensuring they remain firmly in place during operation. 

Over time, a set screw can become worn, stripped, or lost due to regular use or during repairs. A missing or damaged set screw can lead to loose components, which may cause operational issues or even damage other parts of the refrigerator.

Symptoms of a bad Set Screw include:

• Loose or rattling components inside the refrigerator
• Difficulty in keeping parts securely fastened
• Noise coming from the area where the screw is used
• Misalignment of parts, leading to improper functioning

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Door Mullion is an OEM part for GE refrigerators. It is a vertical component that separates the fresh food and freezer compartments, while allowing for the seal and closure of the refrigerator doors.

Causes of a bad door mullion may include physical damage from impact or mishandling, wear and tear over time, or compatibility issues with the specific refrigerator model.

Symptoms that may indicate a need to replace the door mullion include:

• Air leaks or drafts between the fresh food and freezer compartments
• Difficulty in closing or sealing the refrigerator doors properly
• Visible cracks, breaks, or damage to the mullion itself
• Condensation or frost buildup around the mullion area

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models.

Small replacement bumper that mounts on a French-door to cushion contact, reduce rattling and protect the door and cabinet from wear. Restores smoother closing and helps maintain proper door alignment. What it does:

• Cushions the door to prevent metal-to-metal contact and reduce noise.
• Protects the door edge and cabinet finish from wear and impact damage.
• Helps the door align and seat properly for an even, quiet close.
• Commonly used when doors rub, squeak, or close unevenly.

• Disconnect power to the appliance before starting any work.
• Typically installs by pressing or seating into the designated bumper hole or post; may require removing the door or loosening a hinge for full access.
• Inspect surrounding mounting hole and adjacent bumpers; replace any additional worn bumpers for consistent fit.

This is a 10-32 machine-thread screw used to secure appliance panels, trim, and components. It replaces missing or damaged fasteners so parts fit tightly and operate without rattles or misalignment. What it does:

• Fastens panels, brackets, or assemblies that use a 10-32 machine screw
• Restores secure mounting where a stripped, missing, or corroded screw causes looseness
• Helps eliminate vibration noise or gaps caused by loose hardware
• Matches OEM thread size and length for correct fit in designated mounting holes

• One 10-32 x 5/16 machine screw

• Disconnect power and remove power source or batteries before servicing appliances
• Use the correct screwdriver or nut driver to avoid stripping the head
• Thread carefully; do not force or overtighten to prevent thread damage
• Replace any damaged mating hardware or clipped inserts for a secure repair