Parts for Ge PFSS5NFXCSS: 01 - Doors Parts

The GE refrigerator water filter is an OEM replacement part responsible for ensuring the quality of the water dispensed on GE Profile top and bottom freezer refrigerators. It is responsible for purifying the water before it reaches your glass or ice maker, providing you with clean and safe drinking water directly from your refrigerator. To maintain optimal water quality and ensure the filter's effectiveness, it is recommended to replace the filter every 6 months or when the rated capacity of 750 gallons is reached.

Over time, the water filter can become clogged with sediment, reducing its effectiveness. Regular use and the accumulation of minerals and contaminants can lead to the need for replacement.

Symptoms of a bad water filter include:

• Reduced water flow from the dispenser
• Ice cubes with an unusual taste or odor
• The filter indicator light staying on
• Visible particles in the water or ice

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. For the best performance, it is recommended to replace the water filter every six months or as indicated by the filter change light on your refrigerator.

Restore a tight seal and stable temperatures with this refrigerator door gasket. Replacing a worn gasket helps keep cold air in and humid air out to reduce frost, condensation, and unnecessary energy use.

• Forms an airtight seal around the door perimeter
• Helps maintain consistent temperature and humidity
• Reduces frost/ice buildup and interior condensation
• Can address doors that won't close fully or pop open
• Replace if torn, brittle, warped, or not sealing evenly

• Disconnect power before servicing
• Let the gasket warm to room temperature; use warm water or low heat to relax folds
• Remove the old gasket and press the new gasket into the retainer, seating corners first
• Check for even contact all around; adjust door/hinges as needed for a proper seal

This OEM fastener secures interior components and trim on compatible appliances to restore proper fit and reduce movement. It's a direct-replacement hardware piece used where the original mounting screw or retainer is lost or worn. What it does

• Secures panels, trim pieces, brackets or small assemblies to the appliance frame
• Restores firm attachment to reduce rattles, gaps or misalignment
• Replaces missing or stripped hardware that prevents proper part installation
• Helps maintain proper operation by keeping service parts seated and stable

• Disconnect power or unplug the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or driver bit to avoid stripping the head
• Hand-start the fastener, then tighten snugly—do not over-torque
• Replace any additional damaged fasteners with the same OEM part for best fit

This replacement screw fastens refrigerator components securely, restoring a tight, rattle-free fit when original hardware is missing, stripped, or corroded. Use it to secure panels, brackets, or trim and keep parts properly aligned.

• Secures panels, brackets, covers, or trim in place
• Helps maintain correct alignment of components and hardware
• Reduces vibration and rattling caused by loose or missing screws
• Replaces lost, rusted, or stripped screws

• Unplug the refrigerator and turn off water supply if working near water components
• Match thread and length to the removed fastener; hand-start threads to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin sheet metal
• Keep track of any spacers or washers reused from the original assembly

This is a 1/4-10 x 3/4 hex washer head screw that secures panels and components on compatible appliances, restoring proper fit and stability. Use when mounting hardware is loose, missing, or a screw is stripped or broken. What it does:

• Fastens panels, brackets, and assemblies with a hex washer head for a secure hold
• Replaces missing or damaged screws that cause rattling or loose parts
• Restores proper alignment and tension where the original screw was used

• Use the correct 1/4-10 driver or socket to avoid cam-out
• Tighten securely but avoid over-tightening to prevent thread damage
• Replace any stripped mating fastener for best results
• Disconnect power before working on electrical components or near wiring

The Gasket is an OEM part for GE refrigerators, specifically designed to ensure an airtight seal around the refrigerator or freezer door. This crucial component plays a significant role in maintaining the appliance's energy efficiency by preventing cold air from escaping and warm air from entering. 

Causes of a bad Gasket can stem from normal wear and tear over time, accidental damage, or deformation due to improper cleaning methods or exposure to extreme temperatures. 

Symptoms of a bad Gasket include:

• Visible gaps or tears in the gasket material
• Condensation or frost buildup inside the refrigerator or freezer, indicating air leaks
• Difficulty in maintaining consistent internal temperatures
• An increase in energy consumption as the appliance works harder to maintain the desired temperature

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This handle assembly replaces a damaged or worn refrigerator fresh-food door handle to restore a secure grip and straight door appearance. It provides a factory-fit replacement that mounts where the original handle attaches. What it does:

• Replaces a cracked, loose or broken fresh-food door handle
• Restores a safe, comfortable grip for opening the refrigerator door
• Corrects misaligned or crooked handle appearance
• Helps the door latch and seal operate normally by providing proper handle support

• One handle assembly as shown

• Unplug the appliance or disconnect power before beginning any repair
• Keep original fasteners; install with the same screws or clips provided and tighten snugly — do not overtighten
• Handle with care to avoid scratching the door finish; wear gloves to protect hands from sharp edges

This stop door is a small replacement door stop that helps limit and stabilize door movement for proper closing and alignment. Restores consistent door positioning to reduce slamming and wear on the hinge area. What it does:

• Acts as a physical stop to limit door travel and prevent over-rotation
• Helps the door latch and seal properly by holding it in the correct resting position
• Reduces noise and impact from abrupt door closing
• Protects hinge components and surrounding cabinet from excess wear

• Stop door

• Install on the door hinge area where the original stop is mounted; verify orientation before tightening
• Use basic hand tools; avoid over-tightening fasteners which can damage plastic parts
• Disconnect power or unplug the appliance if reaching into areas with electrical components

This module snugger is a small retaining piece used in the refrigerator to hold its associated module or component securely in place. Replacing a cracked or missing snugger restores a tight fit, reduces vibration and noise, and supports correct operation.

• Secures the related module or assembly to prevent shifting
• Helps maintain proper alignment for reliable performance
• Reduces rattles and wear from vibration or movement
• Typical signs it's needed: part is broken or missing, components feel loose, or you hear rattling

• Disconnect power to the refrigerator before servicing
• Note the original orientation and location; take a photo for reference
• Reuse existing fasteners or clips if applicable; avoid overtightening
• After installation, confirm the part holds the assembly firmly and that movement is smooth where intended

This right-hand cam closure is a direct-fit replacement that helps the refrigerator door close and stay aligned for a proper seal. It restores smooth hinge movement and reliable door latching to reduce gaps and cold loss. What it does:

• Guides and secures the door as the hinge rotates to help the door latch fully
• Maintains door alignment to support an even seal and consistent cooling
• Reduces hinge noise and sticking when worn or damaged
• Common symptom: door won't stay closed, rubs, or leaves an uneven gap

• Disconnect power to the appliance before starting any repair
• Support or remove the door per the manufacturer's service instructions to access the hinge/cam
• Replace the cam and reassemble hardware; verify door alignment and operation after installation

This clear dairy door is the flip-up cover for the door-mounted dairy compartment in your refrigerator. It restores a clean look and keeps butter and other small dairy items contained, protected, and easy to access.

• Covers the dairy/butter compartment on the fresh food door
• Helps contain small items and reduce odor transfer
• Attaches to the door bin and flips up for quick access
• Common symptoms: cracked or missing cover, broken hinge tabs, won't stay closed

• Disconnect power to the refrigerator before servicing
• Open the door, support the bin, and gently flex the bin's end tabs to release the old cover
• Align the new cover's hinge pins with the bin openings and snap into place—do not force
• Verify smooth open/close operation before loading items

This wire beverage rack provides a secure place on the refrigerator door to store cans and bottles, keeping drinks organized and easy to reach. It restores proper door storage and prevents items from falling or shifting. What it does:

• Replaces a broken, bent, or missing beverage rack to restore door storage
• Holds cans, bottles and other small drink containers securely on the door
• Stops rattling, sliding, or items falling when the door is opened or closed
• Keeps bottles and cans organized for easier access

• One wire beverage rack

• Designed to attach to the refrigerator door; orientation and clip locations may vary by model
• Remove any damaged rack or clips before installing the replacement
• Install by snapping into the door shelf clips or securing with the existing fasteners; do not force parts into place
• Unplug the appliance or disconnect power before working inside the refrigerator for safety

Color: white. Measures about 15 inches wide by 4-1/2 inches high by 9 inches deep.

This replacement screw secures appliance brackets, panels, and components. It restores a tight, aligned fit when the original hardware is stripped, rusted, or missing, helping reduce vibration and rattling for reliable operation.

• Fastens brackets, panels, or mounts to keep components secure and aligned
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration, rattling, or loose/misaligned parts
• Matches original spec for reliable hold and fit

• Disconnect power before servicing; use proper PPE
• Match thread and length to the removed screw before installation
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Ensure parts are aligned and seating surfaces are clean before tightening