Parts for Ge ZIC36NABRH: 01 - Doors Parts

The Freezer Drawer Gasket is an OEM replacement part for GE refrigerators. It serves as a critical seal between the freezer drawer and the refrigerator cabinet, preventing cold air from escaping and warm air from entering the freezer compartment.

Symptoms of a need to replace the freezer drawer gasket:

• Frost buildup or condensation inside the freezer compartment
• Difficulty opening or closing the freezer drawer due to a poor seal
• Visible gaps, cracks, or damage to the gasket material
• Gasket feeling brittle or not sealing properly when the drawer is closed

Causes of a faulty freezer drawer gasket can include general wear and tear over time, exposure to extreme temperatures, damage from mishandling or improper cleaning, and loss of flexibility or brittleness of the material.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models.

This fresh food door gasket restores a tight seal around the refrigerator compartment on bottom-freezer models. Replacing a worn seal helps keep cold air in, reduce condensation, and maintain stable temperatures and efficiency.

• Seals the perimeter of the fresh food door to prevent air leaks
• Helps maintain proper temperature and humidity inside the refrigerator
• Common signs of failure: tears, warping, gaps, condensation at the door, warm spots, or longer run times
• Can improve door closing and overall cooling performance when the old gasket is damaged

• Unplug the refrigerator before service
• Warm the new gasket in hot tap water to relax and improve flexibility
• Seat the gasket fully into the door channel; on some models you may need to loosen and re-tighten retainer screws
• Use low heat (hair dryer) to smooth waves after install and check for a uniform seal all around

Color: white

This deep fresh food door bin installs on the right-hand refrigerator door to provide sturdy storage for taller containers and everyday items. Replace a broken or missing bin to restore safe, organized space on your refrigerator door.

• Mounts to the right-side fresh food door to hold and organize items
• Deep profile adds capacity for taller containers and bottles
• Replace when the bin is cracked, warped, has broken tabs, or won't stay seated
• Common symptoms: bin falls out, leans, is loose, or is missing

• Empty the old bin; lift straight up to remove from the door liner
• Align the new bin's hooks with the slots and press down until fully seated
• Handle gently; allow plastic to warm to room temperature to reduce cracking risk
• Do not force into place; ensure correct right-side orientation

Color: white

This pack contains twelve replacement screws used to fasten appliance panels, trim, and components. They restore secure mounting and help stop rattling, loose panels, and gaps for a safer, quieter appliance. What it does:

• Secures exterior and interior panels, brackets, and trim pieces
• Restores proper fit where missing or stripped screws cause movement or noise
• Helps maintain appliance alignment and prevents parts from vibrating loose
• Used for general-purpose repairs on compatible GE appliances

• Disconnect power or unplug the appliance before performing any internal repairs
• Use the correct screwdriver bit and avoid overtightening to prevent stripping threads
• Keep remaining screws in a labeled container for future service
• If a screw does not seat easily, stop and verify correct fit to avoid damage

Replacement screw that secures panels and internal components, helping stop rattles and keep parts aligned. Use it to replace stripped, rusted, or missing fasteners and restore a secure fit. What it does:

• Secures panels, trim, or internal parts to prevent movement and vibration.
• Replaces worn, corroded, or missing screws that cause loose panels or rattling.
• Restores proper alignment for doors, covers, and mounted components.
• Provides a simple hardware fix that helps maintain safe, stable operation.

• Always disconnect power to the appliance before accessing internal components.
• Use the correct screwdriver or bit to avoid stripping the head; apply firm but controlled torque.
• Verify screw length, head style, and thread type match the original before installation.
• If threads are damaged, replace with a matching OEM screw rather than over-tightening.