Parts for Ge GFCE1NFBFDSS: Doors Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Replace worn refrigerator door gasket to restore airtight seal, prevent warm air entry, reduce frost, and maintain stable temperatures. Verify fit.

Stainless steel fastener that secures your refrigerator door handle to the door assembly. Replace when original is stripped, missing, or damaged.

Mounting bracket that secures and stabilizes refrigerator panels and assemblies. Replace when the original bracket is broken, cracked, or missing.

Machine screw for refrigerator panels, brackets, and assemblies. Replaces lost, stripped, or damaged fasteners to restore secure fit and stability.

Lower left-hand shelf slide bracket for refrigerators. Supports and guides sliding shelves. Replace if cracked, broken, or missing to restore smooth operation.

Secures brackets, panels, and components inside your refrigerator. Replace stripped, rusted, or missing hardware to restore tight alignment and stability.

This upper drawer slide assembly supports and guides a refrigerator bin beneath its shelf. Replacing a cracked or worn slide restores smooth, aligned drawer movement so the bin opens and closes easily without binding or sagging.

• Provides the track the drawer rides on under the shelf
• Keeps the drawer level and properly aligned for smooth operation
• Typical failure signs: hard-to-open/close drawer, scraping, falling off track, visible cracks
• Helps prevent drooping on one side and restores stable support

• Unplug the refrigerator before servicing.
• Remove the drawer and any contents; handle glass shelves carefully if removal is required.
• Retain and reuse original screws/fasteners or trim pieces.
• Ensure the new slide is fully seated and level before reinstalling the drawer.

Replace a cracked, broken, or missing lower slide-out basket in your refrigerator. Restores organized storage for produce and fresh foods.

Creates an airtight seal to keep cold air in and warm air out. Replace if torn, cracked, or leaking to restore efficiency. Verify fit by model number.

Refrigerator door stop cam riser that mounts to the door hinge. Replacement needed when cracked, broken, or missing to properly support the door.

Plastic retaining clip that secures drawer divider modules in place. Replaces broken, cracked, or missing snuggers to restore proper fit and separation.

Refrigerator door hinge thimble that supports the hinge pin assembly. Replace if cracked, worn, or missing to restore proper door alignment and function.

Replacement right-hand door closure cam for your refrigerator. Installs on the door hinge assembly to control closing action. Replace if cracked or worn.

Left-hand door closure cam for refrigerators. Mounts inside the door hinge assembly to control door closing action. Replace if cracked or broken.

Clear flip-up cover for the door-mounted dairy compartment. Replaces cracked, broken, or missing dairy doors to restore a clean look and keep items secure.

Refrigerator dairy door compartment that mounts on the right door to store butter, cheese, and small items. Replace if cracked, broken, or missing.

Wire beverage rack installs on refrigerator door to organize cans and bottles. Replace if broken, bent, or missing to restore door storage space.

A replacement module shelf assembly that supports and secures a refrigerator's electronic control module and wiring inside the cabinet, helping maintain proper component position and reduce vibration-related connection issues. What it does:

• Provides a stable mounting surface for the main control module and related wiring harness
• Keeps the module correctly positioned to prevent loose connections or intermittent electrical symptoms
• Helps reduce vibration and rattling that can occur when the original shelf is cracked or broken
• Maintains proper spacing to avoid contact with other components that might cause wear or shorting

• One module shelf assembly

• Disconnect power to the appliance before beginning any service
• Handle the shelf and electrical connectors gently to avoid damaging clips or wiring
• Installation typically requires basic hand tools and removing interior panels for access
• Module and harness are fully seated and secured before restoring power

This glass or wire shelf is permanently mounted inside the fresh food compartment of the refrigerator to provide storage space. Replace when the shelf is cracked, broken, or no longer securely holds items due to damaged mounting brackets.

Left-hand freezer rail holder for refrigerators. Secures and stabilizes sliding drawer rails. Replace if cracked, broken, or missing to restore smooth operation.

White mounting screw for ovens and ranges. Secures interior panels, racks, and trim pieces. Replace if screw is stripped, missing, or broken.

Socket set screw for refrigerator interior components. Replace if screw is stripped, missing, or damaged during maintenance. Ensures secure fastening.

This articulation mullion is the flip-out center rail on a French-door refrigerator. It swings into place as the door closes to seal the gap between doors, helping maintain proper temperatures and limit moisture around the center joint.

• Provides the pivoting center rail that engages the opposite door to complete the seal
• Common signs of failure: cracked or loose mullion, won't flip or latch, doors not closing smoothly, or moisture/condensation near the center
• Helps restore proper door sealing and reduce air leaks between doors
• Mounts on the door edge in the same location as the original flipper

• Disconnect power to the refrigerator before servicing
• Remove door bins if needed for access
• Remove mounting screws, lift off the old mullion, position the new mullion, and secure with the original hardware
• Open and close the door to ensure the mullion extends, retracts, and seals correctly

Bottom divider basket for refrigerator freezer compartment. Organizes frozen items and creates separate storage sections. Replace if cracked or broken.

Hex washer head screw secures panels, brackets, and small assemblies inside refrigerators and ranges. Replace stripped, missing, or damaged screws.

Fastens refrigerator panels, brackets, and internal components. Replace this screw if the original is missing, stripped, or damaged to restore secure mounting.

Phillips flat-head screw for securing panels, brackets, and trim inside your refrigerator. Replace missing or stripped screws to keep components aligned.

The Gear Pinion is an OEM component specifically designed for GE French door refrigerators. This part is responsible for the smooth operation of door hinges and closing mechanisms. 

The gear pinion works together with other inner door components to evenly distribute strength across the refrigerator’s motion system. This ensures doors move fluidly and stay securely sealed when closed. 

Causes of a bad gear pinion can include wear from repetitive use over many years, stress from overloading the doors, or misalignment of connecting mechanisms.

Symptoms of a bad gear pinion include: 

• Doors not closing or latching properly
• Binding or sticking movement  
• Noise or vibration when opening/closing
• Increased effort required to operate doors

Note: Right-hand side

Replace this precision gear with a genuine GE OEM part to restore dependable door functionality. This product is also compatible with Hotpoint, RCA, and Kenmore refrigerator models.
 

Push fastener for refrigerator interior panels and trim. Secures shelves, drawers, or housing components. Replace if broken, cracked, or missing.