Parts for Ge GNS22EGEBFBB: Doors Parts

This bracket support is a small mounting bracket that secures and stabilizes appliance components, helping keep panels and assemblies aligned for proper operation and reduced vibration. It's a direct-fit replacement when the original bracket is broken or missing. What it does

• Provides a sturdy mounting point to hold panels or internal components in place
• Restores proper alignment to doors, panels or assemblies that sit on the bracket
• Reduces rattling or vibration caused by a loose or damaged bracket
• Helps prevent wear or damage from parts shifting during use

• Unplug the appliance and shut off water/gas (if applicable) before starting work
• Use the original mounting screws; replace damaged fasteners as needed
• Handle sharp sheet-metal edges carefully and wear gloves and eye protection

This is a 1/4-20 UNC machine screw used to fasten appliance components securely. It restores proper fit and stability where threaded fasteners are required, preventing loose panels or shifting parts. What it does:

• Secures panels, brackets, or assemblies that use a 1/4-20 UNC threaded hole
• Stops rattling or movement caused by a missing or damaged screw
• Restores correct mechanical connection for safe operation
• Useful when replacing stripped, corroded, or lost fasteners

• Disconnect power to the appliance before servicing.
• Start threads by hand to avoid cross-threading; tighten until snug.
• Do not overtighten — use appropriate torque for the material to avoid stripping threads or damaging parts.
• Ensure proper contact and secure fastening.

This refrigerator door gasket forms an airtight seal between the door and cabinet. Replacing a worn or warped gasket restores proper sealing to improve temperature control, reduce frost and condensation, and help your fridge run efficiently.

• Creates a continuous seal around the door perimeter to prevent air leaks
• Helps maintain consistent temperatures and humidity inside the compartment
• Reduces frost, ice, and condensation caused by warm air infiltration
• Common symptoms: tears or warping, visible gaps/light, door not closing fully or popping open, excess frost or moisture

• Unplug the refrigerator before servicing
• Lay the gasket flat and warm it with hot water or gentle heat to relax folds; do not overheat
• Remove the old gasket and press the new one fully into the retainer channel, starting at the corners
• Close the door and check for uniform contact all around; reseat or adjust hinges if needed

A replacement lower right bracket that secures and supports the lower section of the assembly for proper alignment and stable operation. Restores the original mounting point to reduce sagging and movement. What it does:

• Provides a secure mounting point for the appliance's lower assembly so panels, doors or components stay aligned
• Helps prevent sagging, rattling or uneven gaps caused by a damaged or missing bracket
• Maintains correct part-to-frame spacing so connected components operate smoothly
• Fits into the OEM mounting locations and matches factory attachment points

• Disconnect power to the appliance before attempting any repair to avoid shock or injury
• Requires basic hand tools; keep fasteners from the original bracket for reinstallation unless replacements are provided
• Hand-tighten fasteners, then snug to manufacturer torque recommendations—do not overtighten to avoid stripping

This replacement screw secures appliance brackets, panels, and components. It restores a tight, aligned fit when the original hardware is stripped, rusted, or missing, helping reduce vibration and rattling for reliable operation.

• Fastens brackets, panels, or mounts to keep components secure and aligned
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration, rattling, or loose/misaligned parts
• Matches original spec for reliable hold and fit

• Disconnect power before servicing; use proper PPE
• Match thread and length to the removed screw before installation
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Ensure parts are aligned and seating surfaces are clean before tightening

This right-hand replacement slide restores smooth, stable movement for a refrigerator drawer or shelf glide. Designed to support the drawer and keep it aligned for reliable opening and closing. What it does:

• Replaces a worn or broken right-hand drawer/shelf slide to stop sticking or jamming
• Restores proper alignment so the drawer opens and closes evenly
• Reduces rattling or grinding caused by damaged slide hardware
• Helps prevent drawer from falling out or shifting under load

• One right-hand slide

• Remove drawer contents and fully remove drawer before replacing the slide
• Use basic hand tools; keep fasteners and brackets accessible for reassembly
• Inspect the matching left-hand slide and mounting points; replace both if damaged
• If working near electrical components, unplug the appliance before servicing

The Lower Freezer Basket is an OEM replacement part for GE refrigerators designed to fit in the lower section of the freezer, providing a convenient storage area for your frozen items.

A bad lower freezer basket can occur due to regular wear and tear or damage from mishandling. If you notice symptoms such as cracks, broken parts, or difficulty in sliding the basket in and out, it may indicate a need to replace the basket.

Symptoms of a bad lower freezer basket include:

• Cracked or broken basket
• Difficulty in sliding the basket in and out
• Uneven or limited storage space

Restore your refrigerator's freezer section by replacing the faulty lower freezer basket with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This refrigerator French door gasket restores a tight seal around the door opening. Replacing a worn or damaged gasket helps keep cold air in and humid air out to maintain stable temperatures and reduce condensation. What it does:

• Forms an airtight seal between the door and the cabinet on French-door models
• Helps prevent warm air leaks, moisture buildup, and frost around the door opening
• Replace if torn, warped, cracked, or if gaps remain when the door is closed
• Common signs include condensation on or around the gasket and the door not sealing fully

• 1 door gasket

• Unplug the refrigerator and remove items from the door bins
• Warm and relax the new gasket (soak in warm water or use low heat) to remove kinks; do not overheat
• Lift the old gasket out of the retainer; if your model uses retainer screws, loosen them, swap the gasket, then re-tighten
• Press the new gasket fully into the channel, ensure corners seat, then close the door and check for an even seal all around

The Fastener Door Handle is an OEM component for GE refrigerators. This door handle provides a comfortable grip for accessing refrigerator shelves and bins. It attaches securely to the refrigerator door through durable metal fasteners. 

Causes for a bad door handle could be cracks, damage, or stripped fastener holes resulting in a loose or detached handle. Regularly gripping and lifting may also cause normal wear over time.

Symptoms of a failing door handle include:

• The handle detaching completely from the door  
• Looseness making the handle wobbly or unstable to hold
• Sharp edges or broken parts posing a safety risk

This OEM GE handle is also compatible with Hotpoint, RCA, and select Kenmore refrigerator models.

This plastic thimble fits into the appliance cabinet where the door or dispenser mates with the opening, helping provide a smooth seal and protecting surrounding trim from wear. It restores proper fit and reduces rubbing or chafing. What it does:

• Replaces worn or cracked door thimble that can allow rubbing or misalignment at the door opening
• Guides and cushions the door edge or dispenser as it closes, helping reduce noise and abrasion
• Helps maintain a cleaner seal area by covering damaged or missing trim
• Useful when repair requires restoring proper door fit or preventing further trim damage

• One plastic door thimble as described

• Remove power to the appliance before beginning any repair; follow manufacturer's safety guidance
• Typically installs by snapping into the opening or securing with existing fasteners—inspect surrounding clips or screws for damage
• No special tools usually required, but a flat tool can help remove the old thimble; avoid excessive force to prevent cabinet damage
• If replacement does not correct fit or sealing issues, further inspection of hinges, strikes, or surrounding trim may be needed

This refrigerator shelf module provides a sturdy, level surface for food storage. Replace a cracked, damaged, or missing shelf to restore safe storage space, keep items organized, and ensure the shelf seats securely on the cabinet supports. What it does:

• Creates a flat, stable platform for containers and groceries
• Helps organize the interior by maintaining proper spacing between levels
• Locks into the cabinet rails/supports to stay in position
• Common symptoms: cracked or broken shelf/frame, shelf tilts or sags, won't stay seated, missing shelf

• One shelf module

• Disconnect power before servicing interior components
• Remove food items and any obstacles, then release the old shelf from its supports
• Align and seat the new shelf fully in the correct rails/slots; ensure it is level and secure
• Avoid overloading; verify placement per your model's cabinet diagram

This thimble door is the molded trim piece that surrounds the refrigerator/freezer door opening, restoring proper fit and finish. It replaces damaged or worn trim to reduce drafts and improve door alignment and appearance. What it does

• Covers and protects the door opening edge, providing a finished appearance
• Helps maintain a consistent seal by supporting proper door alignment
• Reduces air leaks and drafts at the door opening when installed correctly
• Replaces cracked, warped, or missing trim that can catch or rub during door use

• One thimble door trim piece as shown

• Disconnect power to the appliance before beginning any repair
• Typically secures with clips or screws; inspect existing fasteners and retainers for reuse
• Handle trim gently to avoid cracking; align carefully to ensure a proper fit

This shelf module is a direct-fit replacement that restores a refrigerator shelf's support and stability so stored items sit level and secure. Designed to replace a damaged or worn shelf support on compatible GE refrigerators. What it does

• Provides structural support for a refrigerator shelf so glass or wire shelving stays level
• Replaces broken, cracked, or worn shelf supports that cause sagging or uneven shelving
• Helps prevent stored items from sliding or falling due to a compromised shelf support
• Matches OEM fit and mounting points for straightforward part replacement when applicable

• One shelf module

• Disconnect power or unplug the appliance before starting any repair
• Remove food and move the shelf to access mounting points; follow OEM instructions for removal and installation
• Use basic hand tools; avoid forcing clips or tabs to prevent damage

This set screw secures refrigerator components—most commonly door handles—to their mounting studs. Replacing a missing or stripped screw restores a solid, secure feel and helps prevent loose or wobbly handles.

• Locks the handle to its mounting stud to keep it tight and secure
• Helps resolve a loose, wobbly, sliding, or rattling handle
• Replaces a missing, rounded, or damaged set screw
• Helps maintain proper handle alignment and consistent door operation

• Unplug the appliance or switch off power before servicing
• Ensure the handle is fully seated on the studs before tightening
• Start the screw by hand to avoid cross-threading; then tighten until snug
• Do not overtighten to prevent stripping the screw or handle threads

The Set Screw is an OEM part for GE refrigerators. It is used to secure various components within the refrigerator, ensuring they remain firmly in place during operation. 

Over time, a set screw can become worn, stripped, or lost due to regular use or during repairs. A missing or damaged set screw can lead to loose components, which may cause operational issues or even damage other parts of the refrigerator.

Symptoms of a bad Set Screw include:

• Loose or rattling components inside the refrigerator
• Difficulty in keeping parts securely fastened
• Noise coming from the area where the screw is used
• Misalignment of parts, leading to improper functioning

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Color: Black

Small replacement bumper that mounts on a French-door to cushion contact, reduce rattling and protect the door and cabinet from wear. Restores smoother closing and helps maintain proper door alignment. What it does:

• Cushions the door to prevent metal-to-metal contact and reduce noise.
• Protects the door edge and cabinet finish from wear and impact damage.
• Helps the door align and seat properly for an even, quiet close.
• Commonly used when doors rub, squeak, or close unevenly.

• Disconnect power to the appliance before starting any work.
• Typically installs by pressing or seating into the designated bumper hole or post; may require removing the door or loosening a hinge for full access.
• Inspect surrounding mounting hole and adjacent bumpers; replace any additional worn bumpers for consistent fit.

A replacement Phillips flat-head screw sized 10-14 x 3/4 inch for appliance assembly and panel fastening. Replaces worn or missing fastening hardware to keep panels, brackets, and components secure and aligned. What it does:

• Secures panels, trim, brackets, and internal components where a 10-14 x 3/4" Phillips flat-head screw is required.
• Restores proper fit and prevents rattling, vibration, or gaps caused by missing or stripped screws.
• Provides a direct hardware match for repairs calling for this screw size and head style.

• Disconnect power to the appliance before starting any repair work.
• Use the correct size Phillips screwdriver to avoid stripping the screw head.
• Tighten until snug; avoid over-tightening which can strip threads or crack panels.
• Replace any corroded or damaged mating hardware to ensure a secure fit.