Parts for Ge GTE18ETHKRWW: Doors Parts

This service common handle replaces a worn or broken handle to restore safe, reliable operation and improve the appliance's usability. It provides a direct-fit replacement for the original service handle. What it does

• Replaces a damaged or broken service handle so doors/panels can be opened and closed securely
• Restores proper grip and alignment for normal use
• Helps eliminate rattling or loose-handle symptoms caused by wear or damage
• Matches factory fit to maintain intended operation

• One service common handle (quantity: 1)

• Basic hand tools typically required; disconnect power or follow appliance-specific safety steps before starting
• Inspect mounting area and hardware; reuse or replace fasteners as needed
• Do not force parts; ensure correct alignment to avoid damaging mating components

The Freezer Door Shelf Bar is an OEM replacement part for GE refrigerators. It securely holds up to three adjustable shelves inside the freezer door for organized food storage.

Causes of a bad shelf bar can include damage from overloading shelves, long-term wear and tear from repeatedly loading and removing items, or improper cleaning techniques.

Symptoms of an issue include:

• Shelves sliding out of place due to a loose or unstable bar
• Unable to install shelves into the freezer door
• The bar bending or sagging excessively over time

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models.

This freezer door gasket fits around the door to keep cold air in and moisture out. Replacing a worn or damaged gasket restores proper temperature performance and helps prevent frost and condensation around the freezer opening.

• Creates a tight seal between the freezer door and cabinet
• Helps maintain correct freezer temperature and humidity
• Reduces frost/ice buildup and moisture near the door
• Replaces gaskets that are torn, warped, cracked, shrunken, or not sealing
• Common signs: visible gaps, door not closing fully, frost along the liner, longer run times, or a warming freezer

• Disconnect power; unload items from the freezer door before starting
• Seat the gasket lip evenly into the door channel/retainer all the way around
• Warm the gasket with hot water or a hair dryer on low to help it relax and seal—do not overheat
• Close the door and check for uniform contact; allow time for the gasket to conform

This freezer door stop is a small plastic bumper that cushions and limits the freezer door's travel to prevent over-extension and reduce slamming. It restores proper door positioning and helps protect the cabinet edge. What it does:

• Acts as a door bumper/stop so the freezer door closes and rests correctly
• Reduces slamming and wear on the door and cabinet edge
• Helps keep the door aligned during normal opening and closing
• Can resolve symptoms like a door that over-rotates, hits the cabinet, or doesn't seat cleanly

• One white freezer door stop

• Typically installs by snapping or sliding into the hinge/cabinet mounting location; verify orientation before pressing into place
• Turn power to the appliance off only if panel removal is required; this part is non-electrical
• Use basic hand tools if needed and avoid forcing the part to prevent breakage

The Gasket Door FF is an OEM part for GE refrigerators. This gasket creates a seal around the door frame of the fresh food compartment, helping to maintain the internal temperature by preventing warm air from entering and cold air from escaping. The white gasket measures approximately 28 x 44 inches.

Causes of a bad door gasket can include regular wear and tear, exposure to temperature fluctuations, or physical damage from repeated opening and closing of the door. A compromised gasket can lead to inefficient cooling and increased energy consumption.

Symptoms of a bad gasket door include:

• Warm spots inside the refrigerator
• Condensation or frost buildup around the door
• The door not closing properly
• Visible cracks, tears, or warping of the gasket

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This flip-up dairy door covers the refrigerator's dairy compartment. Replace a cracked or missing cover to keep butter, cheese, and other small items organized and protected while restoring a clean, finished look to the fresh food door.

• Attaches to the dairy bin on the fresh food door and flips up/down for access
• Helps keep contents contained and protected during door opening/closing
• Restores proper hinge/latch engagement so the bin stays closed
• Common symptoms: cracked cover, broken hinge tabs, loose hinge, or missing door

• Empty the dairy bin and remove the old cover
• Align hinge tabs with the bin's pins and snap into place; no tools typically required
• Handle carefully; if very cold, let the plastic acclimate to room temperature before installation
• Open and close to confirm smooth operation and full seating

The Door Shelf Bar is an OEM part for GE refrigerators. This bar is located on the interior side of the refrigerator door. It provides support for items such as condiments, jars, or bottles. It helps to organize the refrigerator and prevent items from tipping or falling during the opening and closing of the door. The Door Shelf Bar is designed to withstand the weight of items placed on it and ensures they are held securely in place.

Causes of a bad Door Shelf Bar can include wear and tear, accidental damage, or improper weight distribution.

Symptoms of a bad Door Shelf Bar may include:

• Cracks or breakage in the bar.
• Difficulty in securely holding items.
• Limited storage capacity due to a damaged or missing bar.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

This replacement door shelf bar restores the front rail on the refrigerator's fresh food door shelf, helping keep bottles and jars contained and organized when the door opens and closes.

• Forms the front rail of a fresh food door shelf to hold items in place
• Replaces a cracked, loose, or missing bar
• Snaps into the existing end slots on the door

• Remove items from the affected door shelf before replacement
• Align the bar with the door's end slots and press until it locks securely
• Always follow appliance safety practices; disconnect power if working near internal components

This reversible door plug fills the unused mounting hole when you switch the door swing on your refrigerator. It restores a finished appearance and helps keep air and moisture from entering through the opening.

• Covers the unused door hole created during a door swing reversal
• Helps maintain proper sealing and resists drafts/condensation at the opening
• Restores a clean, finished, factory look to the door
• Common symptoms: missing or cracked plug, exposed hole, cosmetic gap on door edge

• Disconnect power before servicing any door components
• Gently pry out the old plug with a plastic trim tool to avoid scratches
• Align the new plug with the opening and press until fully seated and flush
• Verify the door closes properly and the gasket seals evenly

This kit replaces the mounting hardware that secures a refrigerator/freezer door handle to the door, restoring a solid, safe grip and clean appearance when the original fasteners are missing, damaged, or stripped.

• Provides the correct hardware to attach and secure the door handle
• Helps resolve loose, wobbly, or detached handles
• Replaces missing, damaged, or stripped handle fasteners
• Supports proper handle alignment and feel

• Disconnect power (and water, if applicable) and wear gloves.
• Support the handle while removing old hardware to prevent drops or scratches.
• Start threads by hand to avoid cross-threading; tighten evenly and do not overtighten.
• The handle is secure and the door opens/closes normally.

Badge assembly that restores the exterior nameplate on compatible refrigerators, returning factory appearance and clear appliance identification. Ideal for replacing faded, cracked or missing emblems for a like-new finish. What it does:

• Restores the appliance's exterior identification and cosmetic finish where the original emblem is faded, cracked, or missing.
• Covers the mounting area and provides the finished look customers expect from the door surface.
• Matches factory styling so the appliance maintains a consistent, OEM appearance.
• Useful whenever visible badge damage detracts from the refrigerator's appearance.

• High-level surface-mount part—inspect the door surface and remove any old adhesive or residue before installing.
• Alignment is important; position carefully and press firmly to engage any snap-in tabs or adhesive backing.
• No electrical disconnection is typically required for exterior cosmetic badges, but avoid prying behind panels that expose wiring or components.

This plug button is a small snap-in cap used on refrigerators to cover exposed holes on door handles, liners, or trim. It restores a clean, finished look while helping keep dust and moisture out of the cabinet.

• Snaps into a screw or access hole on a handle, liner, or trim panel
• Covers fasteners and gaps for a clean, finished appearance
• Helps block dirt and moisture from open holes
• Typical symptoms: missing cap, broken or loose plug, visible screw hole or cosmetic gap

• Unplug the appliance before servicing and use caution around sharp edges
• Align the plug with the hole and press straight in by hand until fully seated and flush
• For handle screw holes, tighten fasteners first, then install the cap
• Avoid using metal tools on finished surfaces to prevent scratches

The Screw is an OEM replacement part for GE brand refrigerators. It is commonly used to secure panels, handles, shelves, or other parts of the refrigerator.

Causes of a faulty refrigerator screw can include wear and tear over time, damage due to mishandling or over-tightening, or loss of thread integrity. These factors can result in loose or ineffective connections, compromising the stability or functionality of the attached components.

Symptoms of a bad refrigerator screw may include:

• Loose or wobbly panels, handles, or shelves
• Difficulty in attaching or securing components
• Visible damage or breakage of the screw

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.