Parts for Ge GTS22KYNBRFS: Doors Parts

This replacement can shelf restores secure, organized storage for beverage cans in your refrigerator. It replaces a cracked, loose, or missing bin so cans stay in place and are easy to access.

• Holds beverage cans securely to help prevent tipping and spills
• Replaces a cracked, warped, or missing shelf/bin
• Restores original storage capacity and organization
• Installs using existing slots/tabs—no modifications required

• Remove the damaged shelf and clean the mounting area
• Align the new shelf's tabs with the slots and press evenly until it locks in place
• Do not force; seat both sides evenly to avoid breaking tabs
• After installation, avoid overloading to prevent damage

This freezer door gasket forms an airtight seal between the door and cabinet to keep cold air in and moisture out. Replace it when the original is torn, warped, or leaking to restore proper temperature and defrost performance.

• Creates a continuous seal around the freezer door to prevent air leaks
• Helps maintain set temperatures and reduces frost/condensation buildup
• Replaces a gasket that is cracked, torn, deformed, or no longer sealing
• Common symptoms: frost or moisture along the door edge, door not closing fully, warm spots near the gasket

• Disconnect power before servicing
• Let the new gasket warm up (room temperature or brief warm-water soak) to increase flexibility
• Seat the gasket fully in the retainer/channel; use low heat (hair dryer) to relax waves—do not overheat
• Check the seal with a paper/dollar-bill test around the perimeter and adjust alignment if needed

This freezer door stop replaces the damaged or worn bumper that cushions the freezer door, helping it close smoothly and preventing damage to the door or cabinet. Color-matched Dorian Gray finish. What it does:

• Cushions door movement to reduce banging and wear
• Helps the door seal more consistently by providing proper stopping position
• Reduces noise when opening or closing the freezer door
• Restores original fit and finish for a clean, finished appearance

• Basic hand tools may be required; follow the appliance manufacturer's instructions
• Power off and empty the door area if required for safe access before installing
• Inspect surrounding trim and mounting area; replace mounting screws if worn or damaged

This replacement refrigerator door stop cushions and limits door travel to help prevent slamming and misalignment. It restores smooth, controlled door movement and helps the door stay properly positioned for reliable sealing. What it does:

• Absorbs impact and reduces door slam noise when opening or closing
• Limits door travel to prevent over-rotation that can damage the cabinet or hinge
• Helps maintain proper door alignment for an effective seal
• Commonly used when a door slams, hangs open, or rubs against the cabinet

• Unplug the appliance or disconnect power before working near electrical components
• Support the door while removing or installing the stop to prevent it from shifting
• Use appropriate hand tools; do not force or overtighten fasteners

This replacement gasket seals the refrigerator's fresh food compartment in Dorian Gray. It closes gaps around the door to keep cold air in and humid air out, helping stabilize temperatures and reduce condensation for reliable cooling.

• Seals the perimeter of the fresh food door to prevent warm air leaks
• Helps maintain proper temperature and humidity in the refrigerator section
• Reduces condensation or "sweating" around the door area
• Common signs it's worn: tears, cracks, warping/shrinkage, visible gaps, or the door not sealing fully

• Unplug the refrigerator and unload the door bins
• Pull the old gasket from the retainer; on some models, slightly loosen (do not remove) liner screws to release the seal
• Warm the new gasket in hot water or with low, safe heat to relax it; seat corners first, then press the gasket fully into the retainer
• Close the door to check for even contact all around; adjust as needed and allow up to 24 hours for the gasket to conform

This replacement dairy door restores the small hinged compartment on the refrigerator door so butter, cheese and other small items stay organized and protected. Fits the 33" door opening on compatible GE refrigerators. What it does:

• Replaces a cracked, chipped or missing dairy door to stop items from falling out and to improve organization.
• Helps maintain a sealed compartment so cold air circulation around small dairy items is more consistent.
• Restores the hinge and latch function if the original door no longer stays closed or is loose.
• Matches OEM fit and form for easy alignment with existing door bins and hardware.

• Disconnect power to the appliance or unplug the refrigerator before starting any service.
• Remove food and door shelves/bins as needed to access mounting points.
• Use basic hand tools (screwdriver/sockets) to remove and install; retain original screws unless replacements are provided.
• Align hinge and test door closure; do not overtighten fasteners to avoid cracking the plastic.

The Modular Door Bin is an OEM part for GE refrigerators. Ideal for organizing smaller grocery items, this versatile storage component installs inside fresh food doors. 

Symptoms of a failing door bin include:

• Cracked or broken plastic unable to securely hold contents  
• Compromised sealing allows spills inside the refrigerator 
• Detaching from mounting brackets during opening/closing

Causes relate to material fatigue from repeated door movements over the years. Exposure to sharp items inside may also damage sealing surfaces.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models. 

This refrigerator door shelf mounts on the inner door to hold condiments, jars, and bottles. Replacing a cracked or missing shelf restores secure, easy-access storage and helps keep items upright when you open and close the door.

• Snaps into the door's molded rails or end tabs to organize and retain containers
• Restores lost door storage capacity for condiments, jars, and tall bottles
• Common symptoms: cracked or broken plastic, loose or missing shelf, items falling from the door
• Visible damage or worn locking tabs prevent the shelf from staying seated

• Remove the old shelf by lifting up and out; empty contents before removal
• Align the new shelf with the door rails/end tabs and press down until fully seated—do not force
• No tools typically required; handle plastic carefully to avoid cracking
• Install in the same location as the original for proper fit and door clearance

This reversible door plug is a small trim cap that fills the unused holes on a refrigerator door after changing the door swing. It restores a clean, finished look and helps keep dust and moisture out.

• Covers unused hinge/handle screw holes created during a door reversal
• Press-fit cap designed to match lighter gray door trim
• Helps maintain appearance and reduce entry of dirt and moisture
• Replace if missing, cracked, discolored, or won't stay seated

• Disconnect power if removing or repositioning the door/hinges
• Use your model's parts diagram to confirm the plug location and color
• Align with the hole and press in by hand until flush with the surface
• Do not force; verify correct part if the plug will not seat properly

This handle mount bushing supports and spaces a refrigerator door handle on its mounting stud, keeping the handle aligned and secure. Replace a cracked or missing bushing to eliminate wobble and restore a tight, flush handle fit.

• Centers the door handle on its mounting stud/post
• Maintains proper spacing so the handle sits flush to the door
• Provides a solid seat for handle fasteners to hold securely
• Failure can cause a loose, wobbly, or misaligned handle

• Open the door and support the handle; protect the finish with tape or a cloth
• Loosen the handle fasteners (set screws or similar) and lift the handle off the studs
• Remove the damaged bushing; seat the new bushing fully on the stud or in the handle base
• Reinstall and align the handle; tighten fasteners evenly without overtightening

This set screw secures refrigerator components—most commonly door handles—to their mounting studs. Replacing a missing or stripped screw restores a solid, secure feel and helps prevent loose or wobbly handles.

• Locks the handle to its mounting stud to keep it tight and secure
• Helps resolve a loose, wobbly, sliding, or rattling handle
• Replaces a missing, rounded, or damaged set screw
• Helps maintain proper handle alignment and consistent door operation

• Unplug the appliance or switch off power before servicing
• Ensure the handle is fully seated on the studs before tightening
• Start the screw by hand to avoid cross-threading; then tighten until snug
• Do not overtighten to prevent stripping the screw or handle threads

The GE Badge is an OEM replacement part for GE refrigerators. It is responsible for displaying the GE branding on the front exterior. Over time, the badge can become damaged from exposure and wear. Causes of a failing badge include sun damage, scrapes, and deterioration of the adhesive.

Symptoms of a bad refrigerator badge:

• Peeling edges or corners
• Discoloration or fading
• Scratches or scuffs
• The badge falling off completely

This GE badge is also compatible with Hotpoint, RCA, and some Kenmore models.

A small plastic thimble that fits behind a push-style control button to hold it squarely in the housing and restore smooth button travel. Replaces a worn or missing retainer to improve button feel and alignment. What it does:

• Secures push-style control buttons in the panel to stop wobble or uneven movement
• Restores proper button travel so controls depress and release cleanly
• Helps keep the button centered in its bezel for consistent operation
• Addresses symptoms like buttons that fall out, sit crooked, or don't return smoothly

• Disconnect power to the appliance before beginning any repair
• Remove the knob or access the control panel per your model's service instructions
• Press the thimble into the button housing until it snaps or seats fully; then reinstall the button/knob

The Screw is an OEM replacement part for GE brand refrigerators. It is commonly used to secure panels, handles, shelves, or other parts of the refrigerator.

Causes of a faulty refrigerator screw can include wear and tear over time, damage due to mishandling or over-tightening, or loss of thread integrity. These factors can result in loose or ineffective connections, compromising the stability or functionality of the attached components.

Symptoms of a bad refrigerator screw may include:

• Loose or wobbly panels, handles, or shelves
• Difficulty in attaching or securing components
• Visible damage or breakage of the screw

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.