Parts for Hot Point HTR16ABSJRBB: 01 - Doors Parts

2 wire insulator.

Secures items in refrigerator door shelves. Replaces cracked, broken, or missing bars that no longer hold bottles and containers in place securely.

Freezer door gasket creates an airtight seal to prevent cool air loss and maintain temperature. Replace when torn, worn, or door won't close properly.

Freezer door gasket creates an airtight seal to keep cold air in. Replace when cracked, torn, or door won't seal properly. Verify fit by model number.

Replace your refrigerator's fresh food door gasket to restore a tight seal, prevent warm air leaks, and reduce frost buildup. Confirm fit with your model.

Seals your refrigerator door to keep cold air in and warm air out. Replace if you notice condensation, frost buildup, or higher energy bills.

Color: white. It measures about 12 inches wide by 6 inches high.

The Freezer Door Shelf Bar is an OEM part compatible with GE refrigerators. This component serves as a support and retaining bar for the shelves located on the inside of the freezer door, ensuring they remain securely in place. This shelf bar measures 23” wide by 2” high and 5” deep

Symptoms that may indicate the need to replace the freezer door shelf bar include:

• Shelves becoming loose or falling out of the freezer door
• The bar itself becoming cracked, bent, or otherwise damaged

Causes of a faulty freezer door shelf bar can include physical impact or mishandling, excessive weight or force applied to the shelves, or general wear and tear over extended use.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models.

Covers unused hinge or mounting holes on refrigerator doors after reversing door swing. Replaces cracked, missing, or damaged plugs for a clean finish.

A replacement reversible plug door that covers and protects the appliance power inlet while letting the cord exit left or right for tidy cord routing. Restores a clean back panel appearance and helps keep the power connection protected from debris. What it does:

• Covers the power inlet opening to protect the plug and inlet from dust and debris.
• Reversible design lets you route the power cord to either side to fit against the wall.
• Helps keep the cord tucked close to the appliance so the unit can sit flush with cabinetry or walls.
• Replace when the door is cracked, broken, missing, or no longer holds the plug securely.

• Always unplug the appliance before starting any repair or inspection.
• May require access to the rear panel; check your owner's manual for disassembly steps.
• Check orientation before finalizing installation to ensure correct left/right cord routing.

Reversible door plug fills unused mounting holes when switching refrigerator door swing direction. Replaces broken or missing plugs for a finished look.

Outer door panel for top-mount refrigerator freezer compartment. Replaces cracked, dented, or discolored panels. Reuses existing handle and shelves.

Outer door panel for top-mount refrigerators. Replaces cracked, dented, or discolored exterior door surfaces. Restores the clean appearance of your unit.

Small control panel insert that secures and centers push buttons. Replaces cracked, broken, or missing thimbles to restore proper button alignment.

Insulating thimble that cushions and centers push button or plug terminals in your refrigerator. Replace if cracked, worn, or missing to restore fit.

This plug button is a small snap-in cap used on refrigerators to cover exposed holes on door handles, liners, or trim. It restores a clean, finished look while helping keep dust and moisture out of the cabinet.

• Snaps into a screw or access hole on a handle, liner, or trim panel
• Covers fasteners and gaps for a clean, finished appearance
• Helps block dirt and moisture from open holes
• Typical symptoms: missing cap, broken or loose plug, visible screw hole or cosmetic gap

• Unplug the appliance before servicing and use caution around sharp edges
• Align the plug with the hole and press straight in by hand until fully seated and flush
• For handle screw holes, tighten fasteners first, then install the cap
• Avoid using metal tools on finished surfaces to prevent scratches