Parts for Kenmore 253.70633411 (25370633411, 253 70633411): Doors Parts

Freezer door gasket keeps an airtight seal around the door to lock in cold air and keep moisture out. Replacing a worn, gray magnetic gasket helps maintain temperature, reduce frost and condensation, and support consistent cooling performance.

• Seals the freezer door perimeter to prevent warm-air leaks
• Helps hold set temperature and reduce frost/condensation
• Replaces torn, warped, or permanently compressed gaskets
• Common symptoms: frost along door edges, door not closing flush, warm spots, or longer run times

• Disconnect power to the refrigerator before servicing
• Warm the gasket in hot water or with a low-heat hair dryer to relax shipping creases; do not overheat
• Seat the gasket bead into the door channel; start at corners and work evenly around
• After installation, check the seal with a paper test and allow up to 24 hours for the gasket to conform; adjust door alignment if needed

The Refrigerator Door Gasket is an OEM replacement part for Frigidaire refrigerators. As a crucial sealing component, it works to prevent air and temperature leakage around the refrigerator door. The gasket creates an air-tight seal when the door is closed, maintaining proper cooling and preserving freshness inside.

The causes of a bad gasket can include cracks, dried-out or degraded rubber, or damage from repeated door openings and closings.

Symptoms of a bad gasket include:

• Increased humidity or moisture inside the refrigerator
• Difficulty keeping temperatures low enough
• Frost or ice build-up around the door perimeter

This OEM part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement bin is the clear storage drawer that holds fruits, vegetables and other refrigerated items, restoring usable storage space and organization in the refrigerator. It's a direct-fit replacement when your existing drawer is cracked, warped or missing. What it does

• Provides a sealed shelf-level compartment to keep fresh food organized and contained.
• Restores proper support and alignment for items stored on the shelf.
• Prevents spills from spreading across the shelf area.
• Helps maintain airflow and separation between storage zones for better organization.

• One replacement clear storage bin.

• Remove food and any shelving before replacing the bin; handle carefully to avoid damage.
• Slide the bin into the existing tracks until it seats; no special tools typically required.
• Inspect mounting rails or glides for wear and replace if damaged to ensure proper operation.
• Keep hands and fingers clear of pinch points when removing or reinstalling the bin.

This clear refrigerator bin stores and organizes food items on a shelf or in a door, keeping groceries contained and easy to access. It replaces cracked, broken, or missing bins so items stop shifting or falling. What it does:

• Holds and organizes produce, deli items, or packaged foods to maximize usable shelf space
• Prevents items from sliding and reduces spills inside the refrigerator
• Restores proper fit where a damaged or missing bin causes gaps or instability
• Compatible with models that use a straight-fit clear storage bin design

• One clear refrigerator bin

• Remove all contents and open the shelf or door fully before installing
• Align bin with shelf rails or mounting slots and slide until it seats securely
• Do not force; if it does not seat easily, inspect for obstructions or misaligned rails
• Clean with mild soap and water; avoid abrasive pads or strong solvents that can damage the plastic

This replacement door bin mounts on the appliance door to hold items securely. Restore organized, usable storage when the original bin is cracked, loose, or missing, and help prevent items from tipping or falling as the door moves.

• Attaches to door liner rails to provide convenient, accessible storage and maximize space
• Replaces a bin that is cracked, warped, broken, or missing
• Common symptoms include broken end tabs, bin won't stay seated, wobbling/sagging, or items falling during door operation
• Matches the original fit for the designated door position on compatible models

• Remove contents; lift the old bin straight up and out of the door slots
• Align the new bin with the tabs/rails and press down until fully seated
• Verify the door closes freely; distribute weight evenly and avoid overloading
• If the bin is very cold, allow it to warm to room temperature before installation to reduce stress on the plastic

This plug button is a small control panel push button used on select Frigidaire appliances to replace a worn or broken button and restore normal user control. It snaps into the panel for a clean, factory-fit appearance. What it does:

• Acts as the tactile push button used to operate a specific control or function on the appliance
• Replaces cracked, loose, or missing buttons that prevent consistent button actuation
• Restores proper contact engagement so the control registers presses reliably
• Helps eliminate cosmetic damage and keeps the control surface sealed against debris

• One plug button

• Snap-in replacement; remove power to the appliance before attempting any service
• If button is attached to an electronics assembly, handle boards and connectors carefully to avoid damage
• Use basic hand tools as needed and avoid forcing parts—verify orientation before snapping into place

Note: Quantity is one plug button.

This is a refrigerator cabinet door designed to replace a damaged or dented outer door panel and restore the appliance's appearance and seal. It provides a solid mounting surface for gaskets, handles, and trim. What it does:

• Replaces a cracked, dented, or scratched outer refrigerator door to improve appearance and function
• Restores proper door alignment and helps maintain an effective door seal when used with a good gasket
• Provides a mounting surface for handles, hinges, and interior trim components
• Helps stop drafts and interior moisture issues caused by damaged door panels

• Keep power disconnected and remove food from door-mounted bins before starting
• Handle with care to avoid scratching finished surfaces; use protective padding during install
• Verify hinge orientation and hardware compatibility before installation; existing hinges, gaskets, and trim may be reused if undamaged

This handle set is the OEM replacement door handle that restores a secure, comfortable grip for opening and appliance doors. It replaces worn, cracked, or broken handles to improve everyday use and appearance. What it does:

• Provides a sturdy grip for opening and closing the appliance door
• Replaces cracked, broken, or loose handles and helps eliminate wobble
• Restores original fit and appearance when the original handle is damaged
• Matches mounting points on the original door for a direct replacement

• Disconnect power and empty the door before starting work to avoid injury or damage
• Use the existing mounting screws and hardware; keep removed fasteners for reassembly
• Support the door while removing or installing the handle to prevent dropping or misalignment

This handle set is the OEM replacement door handle that restores a secure, comfortable grip for opening and appliance doors. It replaces worn, cracked, or broken handles to improve everyday use and appearance. What it does:

• Provides a sturdy grip for opening and closing the appliance door
• Replaces cracked, broken, or loose handles and helps eliminate wobble
• Restores original fit and appearance when the original handle is damaged
• Matches mounting points on the original door for a direct replacement

• Disconnect power and empty the door before starting work to avoid injury or damage
• Use the existing mounting screws and hardware; keep removed fasteners for reassembly
• Support the door while removing or installing the handle to prevent dropping or misalignment

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Screw Kit is an OEM part for Frigidaire appliances. It contains various screws specifically designed to fit and secure different components of Frigidaire appliances, ensuring a tight and secure assembly. This kit is essential for both initial installations and for making repairs or replacements to existing appliances, providing the necessary hardware to maintain or restore the structural integrity of your appliance.  These screws are #10-16 x .500 inches long and can be loosened or tightened using either a Phillips-head or square-head screwdriver.

Symptoms of needing a new Screw Kit include:

• Loose components or panels on your appliance due to missing or damaged screws.
• Inability to securely fasten parts during assembly or repairs, which can lead to operational issues or safety hazards.
• Screws stripping or corroding over time, which can compromise the stability and durability of the appliance.

Causes for replacing screws can include mechanical stress that causes screws to loosen or fall out, environmental factors like moisture leading to corrosion, or accidental damage during cleaning or maintenance.

This screw kit is designed to be universally compatible with various Frigidaire models, ensuring that you have the right screws for a range of repair needs.

The Hinge Bearing is an OEM part for Frigidaire refrigerators. It is designed to facilitate the smooth opening and closing of the refrigerator door by providing a pivot point for the door hinge. This bearing ensures that the door moves easily and remains properly aligned, helping to maintain a tight seal and optimal refrigerator performance.

Causes of a bad hinge bearing can include regular wear and tear from frequent use, exposure to moisture or temperature changes, and physical damage due to accidental impacts. Over time, these factors can cause the hinge bearing to wear out, become loose, or break, affecting the door's functionality.

Symptoms of a bad hinge bearing include:

• Difficulty opening or closing the refrigerator door
• The door not staying in place or sagging
• Unusual noises, such as squeaking or grinding, when the door is moved
• The door not sealing properly, leading to temperature fluctuations inside the refrigerator

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This genuine replacement screw restores a secure hold for panels, trim, or internal components. It replaces worn or missing fasteners so parts stay aligned and appliances operate safely. What it does:

• Fastens panels, brackets, or trim into place
• Replaces stripped, missing, or damaged screws
• Helps stop rattling, loose panels, or misaligned trim
• Fits OEM mounting locations that require the specified machine screw

• Use the correct driver to avoid stripping the head
• Hand-start the screw, then tighten to firm snug; do not over-torque
• Disconnect power to the appliance before accessing internal components
• If other fasteners are damaged, inspect and replace as needed

This part number contains one (1) screw.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a service wrench used to loosen and tighten appliance fasteners for maintenance and repairs, making access and part replacement easier for technicians and DIYers. Durable tool designed for specific appliance fastener sizes. What it does:

• Provides the correct fit and leverage for removing or installing designated appliance nuts, bolts, and fittings
• Helps safely access internal components during service and part replacement
• Reduces risk of rounding fasteners compared with improvised tools
• Useful for routine maintenance tasks and repair procedures that require a dedicated wrench

• One wrench

• Use the wrench only for its intended appliance fasteners; avoid excessive force
• Disconnect power and water to the appliance before beginning service
• Wear safety gloves and eye protection when working on appliances