Parts for Kenmore 253.70633411 (25370633411, 253 70633411): Cabinet Parts

Replaces cracked, broken, or missing compartment cover in your refrigerator. Restores clean appearance and shields internal components and wiring.

Fixes refrigerator running constantly, freezing food, or not cooling properly. This temperature control assembly monitors cabinet temp and cycles cooling.

Refrigerator not cooling but freezer works? Broken evaporator fan blade stops cold air circulation. Easy DIY fix in under an hour with basic tools.

Securing ring holds components in position within your refrigerator assembly. Replace if worn, damaged, or missing to restore proper fit and alignment.

Seals openings where tubes or wires pass through your refrigerator cabinet. Replace if cracked, torn, or causing air leaks. Confirm fit with your model.

If your refrigerator fan rattles or vibrates loudly, this evaporator fan motor grommet cushions the motor mount and stops the noise. Quick DIY fix.

Mounting bracket that secures the shroud or cover to your refrigerator cabinet. Replace this bracket if cracked, bent, or broken to restore alignment.

Replacement cover housing for refrigerators. Shields internal components and restores exterior appearance. Replace if cracked, broken, or missing.

Refrigerator not cooling but freezer works? A failed evaporator fan motor stops cold air circulation. This DIY repair takes 10-15 minutes with basic tools.

Refrigerator interior light won't turn on or stays on? This door light switch controls your fridge lighting. Quick DIY fix with basic tools.

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.

Button plug insert for freezers and refrigerators. Covers screw holes or mounting points on interior walls and shelving. Replace if cracked or missing.

Secures the bottom hinge assembly on your refrigerator door. Replace this bracket if it's bent, broken, or cracked to restore proper door alignment.

Protective washer that sits between the door hinge and frame. Replaces worn or missing washers that cause door sagging, dragging, or poor seal contact.

Hinge spacer that installs between the door hinge and cabinet to restore proper alignment and spacing. Replace when original is cracked, missing, or worn.

Supports and pivots the refrigerator door at the center hinge bracket. Replace if worn, damaged, or missing to restore smooth door swing and alignment.

Secures the top of your refrigerator door to the cabinet. Replace if cracked, broken, bent, or lost during a move to restore proper door alignment.

Replacement shelf support grommet for refrigerators and freezers. Provides stability for shelves. Replace if broken, missing, or worn to restore proper shelf support.

Specs: Hex head ,1/4-20 x 5/8

Fix unresponsive controls or erratic refrigerator operation. This main control board wiring harness restores electrical connections between sensors and switches.

Replacement lower hinge pin for refrigerator doors. Acts as a pivot point to hang and support the door. Replace if worn, broken, or missing from a move.

Mounting screw for refrigerators and freezers. Secures panels, brackets, and internal components. Replace when stripped, missing, or damaged.

Secures panels, brackets, and handles in refrigerators and other appliances. Replace missing or stripped screws to restore secure mounting.

This upper door hinge secures and pivots the refrigerator door for smooth opening and stable closure. It restores proper door alignment to help maintain an airtight seal and even cooling. What it does:

• Provides the pivot point that lets the door open and close reliably
• Helps keep the door aligned so the gasket seals correctly
• Can reduce door sag, rubbing, or uneven gaps
• Addresses symptoms such as a door that hangs, binds, or won't close flush

• Use basic hand tools; support the door while removing or installing hinges to prevent damage or injury
• Tighten mounting hardware securely and check door alignment after installation

Mounting screw for refrigerator assembly. Secures panels, brackets, or components inside your unit. Replace if stripped, missing, or damaged.

This is a gray plastic cover that fits over the lower left door hinge on the refrigerator. It provides a finished appearance and protects the hinge mechanism from dust and debris. Replace this cover if it is cracked, broken, or missing, which can leave the hinge exposed and detract from the appliance's appearance.

Refrigerator cover panel that installs on the exterior or interior cabinet. Replace if cracked, broken, discolored, or missing to restore appearance.

Replacement toe grille kick plate for refrigerator bottom front panel. Covers lower cabinet components and vents. Replaces cracked, broken, or missing grilles.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

Protective cardboard or plastic cover that installs over the internal cooling system and wiring. Replace if cracked, torn, ripped, or missing.

Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.

Secures refrigerator grille or trim to cabinet, preventing rattles and gaps. Replace when broken or missing to restore proper panel alignment. Verify fit with your model number before ordering.

Restores tight seals to stop leaks, drafts, and temperature loss. Replace when you notice gaps, noise, or moisture issues. Verify fit with your model.

This wiring harness routes electrical power/signals between refrigerator components. Replacing a damaged harness helps restore reliable connections so fans, sensors, lights, or the icemaker receive proper power and communication.

• Connects internal refrigerator components to the main wiring circuit
• Can help when there are intermittent power issues to fans, lights, or icemaker
• Designed to fit specific layouts; match connectors to your original for compatibility

• Disconnect power before servicing to avoid electrical shock
• Take photos of existing connector locations to ensure correct reassembly
• Handle connectors by the housings; avoid pulling on wires
• If connectors don't seat easily, re-check orientation—do not force

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head