Parts for Kenmore 790.41113200 (79041113200, 790 41113200): Doors Parts

This decorative exterior trim replaces a worn or damaged appliance trim piece to restore a clean, finished appearance and cover exposed edges. It improves the unit's look and helps hide gaps where panels meet. What it does:

• Covers and finishes exposed edges on the appliance exterior to improve appearance
• Replaces cracked, scratched or discolored trim for a refreshed look
• Helps keep dirt and debris out of panel seams
• Fits into factory mounting points for a flush, OEM-style fit

• Disconnect power to the appliance before beginning any service
• Install by aligning with factory mounting points; fastening hardware or clips may be required
• Handle with care to avoid scratching the finish during installation

This high-temperature insulation is used in the oven assembly to contain heat and protect nearby components and cabinetry. Replacing damaged insulation helps the appliance maintain set temperatures and keeps exterior surfaces from getting excessively hot. What it does:

• Helps retain heat for stable baking and roasting temperatures
• Reduces heat transfer to the appliance frame and adjacent cabinets
• Replaces insulation that is torn, charred, or saturated with spills/grease

• One insulation piece

• Disconnect power; for gas models, also shut off the gas supply
• Remove the range or wall oven and access the oven body
• Wear gloves, eye protection, long sleeves, and a dust mask; fibers can irritate skin and lungs
• Reinstall in the same orientation/routing as the original; do not compress insulation or block vents

A general-purpose replacement screw used to secure appliance panels and components. Installs quickly with a standard screwdriver to restore proper fastening and prevent rattling or loose parts. What it does

• Secures trim, panels, brackets or small components in place
• Restores proper fit to stop vibration, rattling or loose parts
• Replaces lost or stripped fasteners to allow safe operation
• Works where a matching OEM screw is required for correct assembly

• One replacement screw as shown

• Use the correct driver bit to avoid stripping the head
• Tighten snugly but avoid over-torquing to prevent damage to threads or parts
• Disconnect power or follow manufacturer safety steps before accessing internal components

This genuine OEM part is a door assembly for ovens. The door assembly is the front oven door used to gain access to the interior of an oven. Over time, through extensive wear and tear, a door assembly can become damaged, making it difficult to open or close. If the door assembly is not in great working condition, it could be a good time to replace it.To replace the door assembly, open the oven door and remove the screws in the brackets that attach the hinges. Once removed, lift up to pull the door out of its hinges and set to the side. Install the new door by placing it on its hinges and resecure the mounting screws that hold the door in its place. Once secure, open and close the new door assembly to see if it was installed correctly. This replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse ovens.

A genuine replacement refrigerator door handle that restores a secure grip and reliable opening on compatible units. Designed to match the original fit and finish so you can use the door normally again. What it does:

• Replaces a broken, cracked or missing refrigerator door handle
• Provides a solid grip for opening and closing the door smoothly
• Restores proper alignment and appearance of the door front
• Helps prevent further damage from improvised grips or taped-on handles

• One replacement refrigerator door handle

• Basic hand tools typically required; follow the OEM instructions for fastener locations
• Work carefully to avoid scratching the door finish and to retain any mounting clips or screws
• If the handle is near electrical components, unplug the appliance or disconnect power before starting

This cap assembly seals and secures a refrigerator water/ice system connection to prevent leaks and help the dispensing/ice-making system operate properly. It replaces a worn or damaged sealing cap in the water path. What it does:

• Provides a watertight seal at the water/ice connection to prevent drips and leaks
• Helps maintain proper water flow to the dispenser and ice maker
• Stops water pooling or slow fills caused by a damaged cap
• Restores a secure connection when the original cap is cracked, split, or worn

• One cap assembly

• Turn off power and shut off the water supply before replacing the part
• Inspect mating fittings and tubing seals; replace damaged components as needed

Specs: 8 - 18 x 0.500

This spacer sets the correct gap between mating parts in your appliance's assembly, preventing rubbing and misalignment. Replace a missing or worn spacer to restore a solid fit, reduce noise, and protect surrounding components.

• Maintains proper spacing between components for correct alignment and operation
• Reduces metal-to-metal contact, squeaks, and premature wear
• Helps fasteners and panels seat securely
• Typical symptoms when failed: loose or rattling parts, uneven gaps, or visible wear marks

• Disconnect power; for gas models, shut off the gas. Allow the appliance to cool completely.
• Access the assembly per your model's diagram; note the original orientation/stack-up before removal.
• Reuse original fasteners if serviceable; hand-start threads and tighten snugly to avoid damaging the spacer.
• Verify alignment and clearances before fully reassembling. Quantity and location vary by model.

This stainless steel cleaner restores and protects stainless surfaces, removing fingerprints, smudges and light soils to improve appearance and make routine cleaning easier. Safe for finished stainless when used as directed. What it does:

• Cleans away fingerprints, grease, and light residue from stainless surfaces
• Restores a streak-free shine and improves overall appearance
• Helps reduce visible smudges for easier routine maintenance
• Leaves a light protective finish that helps resist fingerprints between applications

• Read and follow the product label before use; test on an inconspicuous area first
• Apply to a soft cloth and wipe with the grain of the stainless; avoid abrasive pads
• Do not use on hot surfaces, painted finishes, or unsealed metals unless manufacturer approves
• Keep out of reach of children and avoid contact with eyes; if contact occurs, rinse thoroughly

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts