Parts for Kenmore 790.78153413 (79078153413, 790 78153413): Doors Parts

This trim piece is a factory-style decorative/replacement trim for your refrigerator door that restores a finished appearance and protects the door edge from wear. It matches OEM fit and finish for a clean, finished look. What it does:

• Covers and protects the exposed edge of the refrigerator door for a finished appearance
• Hides gaps between door components and the cabinet for improved aesthetics
• Replaces cracked, chipped or worn trim that detracts from the appliance appearance
• Helps maintain an even seal line by keeping trim aligned and intact

• One refrigerator door trim piece

• High-level replacement — typically held by clips or screws; remove door panels or inner liners only if required by your model
• Power off and unplug the appliance before beginning any repair that requires panel removal
• Use care to avoid scratching adjacent surfaces during installation; retain all fasteners

This heat-resistant insulation helps contain oven heat and shield surrounding components. Replacing worn insulation supports faster, more consistent preheating, steadier baking temperatures, and cooler exterior panels for safer, more efficient operation. What it does:

• Wraps/lines the oven cavity or panels to reduce heat loss and protect nearby wiring and controls
• Helps the oven preheat efficiently and maintain consistent cooking temperatures
• Limits heat transfer to exterior panels and surrounding cabinetry
• Common signs of failure: longer preheat times, temperature swings, unusually hot sides/back, or insulation that is burnt, brittle, soaked, or missing

• 1 insulation piece

• Disconnect power and, if applicable, shut off gas before servicing
• Access typically requires removing rear/side panels or sliding the unit out; take photos to aid reassembly
• Wear gloves and a dust mask; handle gently—do not compress insulation and keep clear of sensors/wiring
• Re-secure with original clips/tape, reinstall panels, then test preheat and check for abnormal exterior heat

This high-temperature insulation is used in the oven assembly to contain heat and protect nearby components and cabinetry. Replacing damaged insulation helps the appliance maintain set temperatures and keeps exterior surfaces from getting excessively hot. What it does:

• Helps retain heat for stable baking and roasting temperatures
• Reduces heat transfer to the appliance frame and adjacent cabinets
• Replaces insulation that is torn, charred, or saturated with spills/grease

• One insulation piece

• Disconnect power; for gas models, also shut off the gas supply
• Remove the range or wall oven and access the oven body
• Wear gloves, eye protection, long sleeves, and a dust mask; fibers can irritate skin and lungs
• Reinstall in the same orientation/routing as the original; do not compress insulation or block vents

The Screw is an OEM replacement part for Frigidaire appliances. This screw is used to securely fasten components, such as panels, brackets, or internal parts, ensuring the appliance remains stable and functions correctly. Its precise design ensures a snug fit and reliable performance in the designated area of the appliance.

Over time, screws can become stripped, corroded, or loosened due to vibrations, frequent use, or environmental factors. A damaged or missing screw may lead to instability, misaligned components, or operational issues with the appliance.

Symptoms of a bad or missing screw include:

• Loose or misaligned panels or components
• Rattling or unusual noises during operation
• Difficulty in securing parts during repairs or adjustments
• Parts becoming detached or unstable

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This spacer positions and supports adjacent appliance components to keep parts aligned, reduce contact, and help prevent rubbing or vibration. It's a simple replacement that restores correct spacing for reliable operation. What it does:

• Keeps panels, trim, or internal components properly spaced to prevent rubbing and wear
• Helps maintain door/panel alignment and even gaps
• Reduces vibration noise caused by metal-to-metal contact
• Restores correct part clearance after service or component replacement

• Disconnect power before working on the appliance to avoid shock or injury
• Small part — keep track of fasteners and any removed components during disassembly
• Typically installed with basic hand tools; follow OEM diagram for exact location and orientation
• Do not force or modify the spacer; replace with the correct part for proper fit

This spacer positions and cushions refrigerator components to prevent contact and reduce vibration, helping panels and assemblies align correctly for reliable operation. Lightweight and simple to install, it restores proper fit where the original spacer is damaged or missing. What it does:

• Keeps panels, trim, or internal components spaced correctly to maintain alignment
• Absorbs minor vibration and prevents metal-to-metal contact that can cause noise
• Helps preserve seals and door alignment by maintaining correct component clearance
• Common symptom: loose trim, rubbing panels, rattling, or visible gap where a spacer is missing

• One spacer

• Disconnect power to the appliance before beginning any work
• Remove adjacent panels or trim as needed to access the spacer; retain fasteners for reassembly
• Inspect surrounding clips or mounting points and replace any damaged hardware

This hinge secures and pivots the upper refrigerator door to keep it aligned and operating smoothly. It restores proper door movement and helps maintain a tight seal for efficient cooling. What it does:

• Provides the pivot point that lets the upper door open and close smoothly
• Keeps the door aligned to prevent sagging or rubbing against the cabinet
• Helps maintain a consistent door seal to reduce cold air loss
• Can stop clicking, grinding or loose-door symptoms when worn or damaged

• High-level task: remove door trim or stop and support the door before unfastening hinge screws.
• Use proper tools and a second person to support the door; avoid letting the door drop.
• Always disconnect power (and water line if applicable) before beginning work.
• Replace only with the exact part number to ensure fit; tighten fasteners to secure the hinge.

A small mounting spacer used to position and support appliance components for correct alignment and stable operation. Replaces a worn or missing spacer to help restore proper fit between panels and parts. What it does:

• Keeps panels, brackets, or components spaced correctly to prevent rubbing and misalignment
• Helps reduce vibration and rattling caused by gaps or loose fits
• Restores correct clearance for moving parts that need precise spacing
• Used wherever a fixed gap or support is required between parts

• Disconnect power (and fuel or water if applicable) before beginning any repair
• Access may require removing outer panels, trim, or adjoining components
• Keep orientation and placement the same as the original spacer; install snugly but avoid over-tightening
• If other parts show wear or damage, inspect and replace them as needed for a complete repair

A genuine replacement refrigerator door handle that restores a secure grip and reliable opening on compatible units. Designed to match the original fit and finish so you can use the door normally again. What it does:

• Replaces a broken, cracked or missing refrigerator door handle
• Provides a solid grip for opening and closing the door smoothly
• Restores proper alignment and appearance of the door front
• Helps prevent further damage from improvised grips or taped-on handles

• One replacement refrigerator door handle

• Basic hand tools typically required; follow the OEM instructions for fastener locations
• Work carefully to avoid scratching the door finish and to retain any mounting clips or screws
• If the handle is near electrical components, unplug the appliance or disconnect power before starting

This appliance screw fastens panels, brackets, and other components inside the unit. Replace a missing, rusty, or stripped fastener to restore a secure fit and help prevent rattles, misalignment, or premature wear.

• Secures appliance components such as panels, brackets, and covers
• Restores proper fit when an original screw is missing or stripped
• Helps reduce vibration and noise from loose parts
• Common signs: loose or misaligned parts, rattling, or a missing screw

• Disconnect power before servicing
• Match the new screw to the original for size and thread before installing
• Hand-start threads to avoid cross-threading; do not overtighten
• Reuse any original washers or clips if they were used with the old screw

This appliance screw fastens panels, brackets, and other components inside the unit. Replace a missing, rusty, or stripped fastener to restore a secure fit and help prevent rattles, misalignment, or premature wear.

• Secures appliance components such as panels, brackets, and covers
• Restores proper fit when an original screw is missing or stripped
• Helps reduce vibration and noise from loose parts
• Common signs: loose or misaligned parts, rattling, or a missing screw

• Disconnect power before servicing
• Match the new screw to the original for size and thread before installing
• Hand-start threads to avoid cross-threading; do not overtighten
• Reuse any original washers or clips if they were used with the old screw

This stainless steel cleaner restores and protects stainless surfaces, removing fingerprints, smudges and light soils to improve appearance and make routine cleaning easier. Safe for finished stainless when used as directed. What it does:

• Cleans away fingerprints, grease, and light residue from stainless surfaces
• Restores a streak-free shine and improves overall appearance
• Helps reduce visible smudges for easier routine maintenance
• Leaves a light protective finish that helps resist fingerprints between applications

• Read and follow the product label before use; test on an inconspicuous area first
• Apply to a soft cloth and wipe with the grain of the stainless; avoid abrasive pads
• Do not use on hot surfaces, painted finishes, or unsealed metals unless manufacturer approves
• Keep out of reach of children and avoid contact with eyes; if contact occurs, rinse thoroughly

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.