Parts for Kenmore 790.97723410 (79097723410, 790 97723410): Doors Parts

This high-temperature insulation is used in the oven assembly to contain heat and protect nearby components and cabinetry. Replacing damaged insulation helps the appliance maintain set temperatures and keeps exterior surfaces from getting excessively hot. What it does:

• Helps retain heat for stable baking and roasting temperatures
• Reduces heat transfer to the appliance frame and adjacent cabinets
• Replaces insulation that is torn, charred, or saturated with spills/grease

• One insulation piece

• Disconnect power; for gas models, also shut off the gas supply
• Remove the range or wall oven and access the oven body
• Wear gloves, eye protection, long sleeves, and a dust mask; fibers can irritate skin and lungs
• Reinstall in the same orientation/routing as the original; do not compress insulation or block vents

This interior cabinet liner replaces a damaged or cracked refrigerator cabinet panel to restore a clean, sealed interior surface and proper mounting for shelves or components. It helps maintain interior hygiene and prevents airflow leaks. What it does

• Provides the finished interior surface for the refrigerator cabinet and supports shelf and accessory mounting.
• Covers and protects insulation and internal cavity areas from spills, stains, and physical damage.
• Helps maintain proper airflow paths and compartment sealing to support cooling performance.
• Commonly replaced when the liner is cracked, warped, damaged by impact, or permanently stained.

• One interior cabinet liner panel as shown.

• Liners may require panel clips, screws, or adhesive (verify retained fasteners).
• Disconnect power and empty the compartment before starting to avoid injury or damage.
• Handle carefully to avoid cracking or scratching the replacement liner during installation.
• Reuse or replace any trim, clips, or fasteners only if they are present and in good condition.

This door assembly replaces a damaged or dented outer refrigerator door to restore a clean exterior and proper sealing. It provides the structural panel and mounting points needed for door hardware and trim. What it does:

• Replaces a bent, cracked, or cosmetically damaged outer refrigerator door panel
• Restores proper alignment for door handles, hinges, and trim pieces
• Helps maintain correct door closure to protect internal temperatures
• Stops drafts and visible damage that can lead to moisture buildup or further wear

• Handle, hinge screws, and trim may need transfer from original door
• Disconnect power to the appliance and remove food before working on doors
• Support the door during removal/installation to avoid damage or injury

This spacer positions and cushions refrigerator components to prevent contact and reduce vibration, helping panels and assemblies align correctly for reliable operation. Lightweight and simple to install, it restores proper fit where the original spacer is damaged or missing. What it does:

• Keeps panels, trim, or internal components spaced correctly to maintain alignment
• Absorbs minor vibration and prevents metal-to-metal contact that can cause noise
• Helps preserve seals and door alignment by maintaining correct component clearance
• Common symptom: loose trim, rubbing panels, rattling, or visible gap where a spacer is missing

• One spacer

• Disconnect power to the appliance before beginning any work
• Remove adjacent panels or trim as needed to access the spacer; retain fasteners for reassembly
• Inspect surrounding clips or mounting points and replace any damaged hardware

A small mounting spacer used to position and support appliance components for correct alignment and stable operation. Replaces a worn or missing spacer to help restore proper fit between panels and parts. What it does:

• Keeps panels, brackets, or components spaced correctly to prevent rubbing and misalignment
• Helps reduce vibration and rattling caused by gaps or loose fits
• Restores correct clearance for moving parts that need precise spacing
• Used wherever a fixed gap or support is required between parts

• Disconnect power (and fuel or water if applicable) before beginning any repair
• Access may require removing outer panels, trim, or adjoining components
• Keep orientation and placement the same as the original spacer; install snugly but avoid over-tightening
• If other parts show wear or damage, inspect and replace them as needed for a complete repair

A genuine replacement refrigerator door handle that restores a secure grip and reliable opening on compatible units. Designed to match the original fit and finish so you can use the door normally again. What it does:

• Replaces a broken, cracked or missing refrigerator door handle
• Provides a solid grip for opening and closing the door smoothly
• Restores proper alignment and appearance of the door front
• Helps prevent further damage from improvised grips or taped-on handles

• One replacement refrigerator door handle

• Basic hand tools typically required; follow the OEM instructions for fastener locations
• Work carefully to avoid scratching the door finish and to retain any mounting clips or screws
• If the handle is near electrical components, unplug the appliance or disconnect power before starting

This support bracket secures and stabilizes appliance components, restoring proper alignment and stopping movement. It's a simple replacement that helps reduce rattling and prevents panels or assemblies from shifting during use. What it does:

• Provides a rigid mounting point to hold panels, trim, or internal assemblies in place
• Restores proper alignment when a worn or broken bracket causes gaps or looseness
• Reduces vibration and rattling caused by a damaged or missing support
• Keeps connected parts from shifting, which can prevent further wear or damage

• Disconnect power to the appliance before beginning any repair
• Verify the bracket orientation and fit against the mating surface before fastening
• Use the factory screw locations and hardware; tighten screws securely but avoid over-torquing

This appliance screw fastens panels, brackets, and other components inside the unit. Replace a missing, rusty, or stripped fastener to restore a secure fit and help prevent rattles, misalignment, or premature wear.

• Secures appliance components such as panels, brackets, and covers
• Restores proper fit when an original screw is missing or stripped
• Helps reduce vibration and noise from loose parts
• Common signs: loose or misaligned parts, rattling, or a missing screw

• Disconnect power before servicing
• Match the new screw to the original for size and thread before installing
• Hand-start threads to avoid cross-threading; do not overtighten
• Reuse any original washers or clips if they were used with the old screw

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

This stainless steel cleaner restores and protects stainless surfaces, removing fingerprints, smudges and light soils to improve appearance and make routine cleaning easier. Safe for finished stainless when used as directed. What it does:

• Cleans away fingerprints, grease, and light residue from stainless surfaces
• Restores a streak-free shine and improves overall appearance
• Helps reduce visible smudges for easier routine maintenance
• Leaves a light protective finish that helps resist fingerprints between applications

• Read and follow the product label before use; test on an inconspicuous area first
• Apply to a soft cloth and wipe with the grain of the stainless; avoid abrasive pads
• Do not use on hot surfaces, painted finishes, or unsealed metals unless manufacturer approves
• Keep out of reach of children and avoid contact with eyes; if contact occurs, rinse thoroughly

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts