Parts for Craftsman 358791540: Driveshaft / Handle / Shield Parts

This is a replacement purge bulb. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part is intended to replace a broken or defective purge bulb on various models of outdoor power equipment. The purge bulb purges air from the carburetor and draws in fuel from the fuel tank to allow the engine to start. Over time, the purge bulb can crack or become brittle, requiring replacement. Proper tools are required to replace this part and work gloves are advised. It is always recommended that the appropriate safety precautions are adhered to when attempting to fix any power tools or machinery. When working on or near an engine, ensure the equipment is turned off and completely cooled down before starting any repairs. For more accurate information on how and where to install this purge bulb, the appropriate owner's manual and included diagrams should be referenced. As an authentic replacement part, this purge bulb is suitable for use on several different models of small engine power equipment such as string trimmers, leaf blowers, and edgers manufactured by Husqvarna, Craftsman, WeedEater, and Poulan. This is a genuine part made of high-quality, durable, non-corrosive materials and is sold individually.

This replacement part is a screw. This part is a genuine replacement part made by Husqvarna. Screws are small but important in many different types of machinery. Screws are able to hold different parts in place and help them stay secure during use so that the machine can operate smoothly and efficiently. A new screw might be needed if the current one is missing or damaged in any way. It is possible that the screw can become stripped over time and therefore not stay in place properly. If this is the case it is recommended that it be replaced. This repair should be fairly easy and only require a screwdriver and possible pliers. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit and long-lasting use. Note that This is a genuine OEM replacement part.

This replacement part is an assembly wire guard. This part is commonly found in line trimmers or edgers and is responsible for assisting the user in performing an accurate cut during any job. A new assembly wire guard might be needed if the current one is missing or damaged in any way. This can be from wear and tear after years of normal use or from a single incident that may have caused it to no longer work properly. If the assembly has become dented, bent, or cracked, it might be time to replace it. This is a genuine OEM replacement part manufactured by Husqvarna. This part is sold individually.

This replacement part is a line guide, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by Husqvarna. This line guide is small but aids in creating straight lines while cutting the grass in many different lawn mowers. A new line guide might be needed if the user notices the current one is not working properly. If the cutting lines of grass are not as straight as normal there might be an issue with the line guide inside of the machine. Be sure to wear working gloves while replacing this part as it is typically found near the blades of the appliance. This small part is sold as a single piece. This part is a genuine OEM part sourced directly from the manufacturer. Be sure to reference the specific owner's manual for more information on how to replace this part.

This is a cap assembly designed for gas string trimmers. The cap assembly is installed at the base of the trimmer's drive shaft, over the spool real. It is responsible for the advancement of the trimmer line in the spool when hit against the ground and also serves to protect the spooled trimmer line from dust and debris. The cap is made of durable plastic and is meant to absorb shock from the ground. However, over time, the threads on the cap's interior may become worn out. Blows from hard surfaces like asphalt and concrete may cause the cap to weaken and even break. A cap that fails to remain in place or is significantly damaged needs to be replaced.The installation of a new cap assembly is easy. First, remove the old cap assembly. The use of an adjustable wrench or vice grips might be necessary depending on the old cap's threading. Once the old cap is removed, then simply screw the new one on, making sure it firmly fastened.This is an OEM part sourced directly from the manufacturer. It is sold individually. The cap assembly is compatible with Craftsman and Husqvarna trimmer models.