Need Help?
Call or text
Show parts
Usually ships within 4 - 14 days
This replacement part is a screw. It is a genuine replacement part made by Husqvarna. Screws are small yet very important to the overall operations of many different machines and appliances. Screws are able to hold other parts in place and secure so that everything can operate smoothly. A new screw might be needed if the user notices that the current ones are damaged or missing. It is possible that screws become stripped or lodged over time and must be replaced. The repair should be fairly easy, only requiring a screwdriver or pliers if the previous screw is stuck. Be sure the engine is completely powered down before starting a repair. This screw is sold individually. Be sure to purchase the correct amount as many appliances require more than one. This is a genuine OEM replacement part sourced directly from the manufacturer.
This part is discontinued by the manufacturer and is no longer available for purchase.
This authentic OEM replacement on/off switch is a safety measure that manufacturers install to prevent the chainsaw or trimmer from starting before the operator is ready. It also allows the operator to stop their appliance at a moment's notice if they lose control of it. The on/off switch is located in or near the handle of the appliance and must be in the on position for the appliance to start. If hit to the off position, the appliance will immediately stop running. Switches can slowly wear out over time due to repeated use. When it wears out, the switch will no longer give the same amount of resistance and may be tripped more easily. This can be frustrating as it means that the operator would have to continually restart their appliance. To replace the switch, use a screwdriver to access the handle interior and detach the wiring from the old switch. Install the new part and reassemble. This switch is a high-quality replacement part for Craftsman chainsaws and trimmers, and as such, it comes sourced directly from the original manufacturer. This part ships individually.
The handle assist is the handle that is held to steer and control the machine during the trimming process. As the primary touchpoint, the handle has to provide enough comfort while assisting with the machine's function. This handle is designed to be gloves-friendly with a surface rough enough to provide security against slip. Use this as a replacement for a broken, loose, or worn handle. Remember always to hold the handle firmly while operating. This part is designed for use on trimmers or weed cutters made by Craftsman, Weed Eater, Poulan, or Poulan Pro. This is a genuine OEM replacement handle that will provide extra control and less hand fatigue. It is sold individually.
All gasoline-powered trimmers must have throttle controls that increase the amount of gasoline flowing into the carburetor. As the amount of fuel increases and the engine revolutions increase, the clutch engages the spool and the trimming line begins to turn. The throttle trigger assembly is quite durable. However, it has several appendages and is required to be under constant pressure when in use. If any of the design parts fail, the trigger unit must be replaced or the trimmer cannot be used. To replace the throttle trigger, open the housing and disconnect the throttle cable from the old trigger. It's easy to see where the new trigger will fit in the housing because the screw holes will line up perfectly with the holes in the new throttle trigger. The throttle cable will fit into one slot on the new trigger and a spring opposite the slot will hold the trigger unit at the proper angle as the housing is replaced. This new throttle trigger is an OEM replacement part, made to the same exacting specification as the original. This throttle control is designed by Craftsman and used on most of their trimmers. It is also compatible with a few other manufacturers' trimmers, including Poulan and Husqvarna.
This part is a replacement D-handle nut. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part is intended for use as a replacement in a defective or misplaced nut in outdoor power equipment. This D-handle nut is a standard piece of hardware and thus has many functions. The D-handle enables this nut to be easily tightened and loosened by the user. Nuts can easily become worn, corroded, or lost, requiring replacement. Proper tools are not required to install this D-handle nut. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to install this D-handle nut, the appropriate owner's manual and equipment diagrams should be referred to. This D-handle nut is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with small engine outdoor power equipment that has been manufactured by Husqvarna, Poulan, and other brands.
The lower shaft replacement is used for lawn and garden equipment such as trimmers, gas trimmers, and pruners. The shaft is the part that will hold the spool used on these types of equipment. It also connects to the upper shaft.Some of the common problems with the lower drive shaft include worn drive shaft ends, worn bushing, breaks along the metal, or damage to the outer tube. Owners should replace the lower shaft before they use the machine. Continuing to use a trimmer with a broken lower shaft is dangerous and could result in injury or more damage to the machine. The replacement of the lower shaft is relatively simple and will require only a few tools.The replacement part works with certain models of trimmer and pruner from Husqvarna, Weed Eater, and Poulan. This is a genuine OEM replacement part sourced from the manufacturer. The kit is sold individually.
This shield kit is a genuine Husqvarna replacement part for a line trimmers and pole saws. The shield kit, also known as a guard, is a safety precaution to protect the engine from damage and to protect the appliance user from flying debris. The shield also manages the amount of string trimmer line that is spooled out. The shield kit of a line trimmer or pole saw might have to be replaced if there is significant damage to the exterior. While shield kits for line trimmers and pole saws are designed to be durable, the exterior can be gradually worn away by collisions with flying debris and small stones, causing warping and erosion to the plastic material. If the shield kit is damaged, it must be removed and replaced immediately, as it is important for safe use of the appliance. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This shield kit is compatible with the following brands: Husqvarna, Weed Eater, Craftsman, and Poulan. This part sold individually.
The spool retainer replacement is used for trimmers and pruners. It helps to secure the spool in the hub assembly of the machines, so it will hold the line or string. Without a functioning spool retainer, it would be impossible to use the machine properly. The spool retainer can start to wear out over time and no longer function correctly. It might become broken, as well. Replacing the retainer is essential, and it is an easy replacement to make. The spool can be pressed into the hub assembly and it releases just as easily. This is a genuine OEM replacement part that is sold individually. It works with certain makes and models of pole pruners and trimmers. Compatible brands include Craftsman, Husqvarna, Weed Eater, Poulan, and Poulan Pro. When buyers are choosing the new spool retainer, they should ensure they are buying the correct replacement part.