Parts for Poulan PP136E TYPE 2: Driveshaft / Shield / Handle Parts

This replacement part is a screw. It is a genuine replacement part made by Husqvarna. Screws are small yet very important to the overall operations of many different machines and appliances. Screws are able to hold other parts in place and secure so that everything can operate smoothly. A new screw might be needed if the user notices that the current ones are damaged or missing. It is possible that screws become stripped or lodged over time and must be replaced. The repair should be fairly easy, only requiring a screwdriver or pliers if the previous screw is stuck. Be sure the engine is completely powered down before starting a repair. This screw is sold individually. Be sure to purchase the correct amount as many appliances require more than one. This is a genuine OEM replacement part sourced directly from the manufacturer.

This authentic OEM replacement on/off switch is a safety measure that manufacturers install to prevent the chainsaw or trimmer from starting before the operator is ready. It also allows the operator to stop their appliance at a moment's notice if they lose control of it. The on/off switch is located in or near the handle of the appliance and must be in the on position for the appliance to start. If hit to the off position, the appliance will immediately stop running. Switches can slowly wear out over time due to repeated use. When it wears out, the switch will no longer give the same amount of resistance and may be tripped more easily. This can be frustrating as it means that the operator would have to continually restart their appliance. To replace the switch, use a screwdriver to access the handle interior and detach the wiring from the old switch. Install the new part and reassemble. This switch is a high-quality replacement part for Craftsman chainsaws and trimmers, and as such, it comes sourced directly from the original manufacturer. This part ships individually.

This replacement part is a screw. It is a genuine replacement part made by Husqvarna. Screws are small yet very important to the overall operations of many different machines and appliances. Screws are able to hold other parts in place and secure so that everything can operate smoothly. A new screw might be needed if the user notices that the current ones are damaged or missing. It is possible that screws become stripped or lodged over time and must be replaced. The repair should be fairly easy, only requiring a screwdriver or pliers if the previous screw is stuck. Be sure the engine is completely powered down before starting a repair. This screw is sold individually. Be sure to purchase the correct amount as many appliances require more than one. This is a genuine OEM replacement part sourced directly from the manufacturer.

All gasoline-powered trimmers must have throttle controls that increase the amount of gasoline flowing into the carburetor. As the amount of fuel increases and the engine revolutions increase, the clutch engages the spool and the trimming line begins to turn. The throttle trigger assembly is quite durable. However, it has several appendages and is required to be under constant pressure when in use. If any of the design parts fail, the trigger unit must be replaced or the trimmer cannot be used. To replace the throttle trigger, open the housing and disconnect the throttle cable from the old trigger. It's easy to see where the new trigger will fit in the housing because the screw holes will line up perfectly with the holes in the new throttle trigger. The throttle cable will fit into one slot on the new trigger and a spring opposite the slot will hold the trigger unit at the proper angle as the housing is replaced. This new throttle trigger is an OEM replacement part, made to the same exacting specification as the original. This throttle control is designed by Craftsman and used on most of their trimmers. It is also compatible with a few other manufacturers' trimmers, including Poulan and Husqvarna.

The handle assist is the handle that is held to steer and control the machine during the trimming process. As the primary touchpoint, the handle has to provide enough comfort while assisting with the machine's function. This handle is designed to be gloves-friendly with a surface rough enough to provide security against slip. Use this as a replacement for a broken, loose, or worn handle. Remember always to hold the handle firmly while operating. This part is designed for use on trimmers or weed cutters made by Craftsman, Weed Eater, Poulan, or Poulan Pro. This is a genuine OEM replacement handle that will provide extra control and less hand fatigue. It is sold individually.

This part is a replacement D-handle nut. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part is intended for use as a replacement in a defective or misplaced nut in outdoor power equipment. This D-handle nut is a standard piece of hardware and thus has many functions. The D-handle enables this nut to be easily tightened and loosened by the user. Nuts can easily become worn, corroded, or lost, requiring replacement. Proper tools are not required to install this D-handle nut. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to install this D-handle nut, the appropriate owner's manual and equipment diagrams should be referred to. This D-handle nut is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with small engine outdoor power equipment that has been manufactured by Husqvarna, Poulan, and other brands.

This replacement part is an upper shaft and is intended for use in a variety of lawn equipment. This is a genuine replacement part made by Husqvarna. This upper shaft is typically found in hedge trimmers and is an important part to this appliance. This part is able to connect the power source from the top of the appliance to the trimmer head at the bottom so that the drive mechanisms is activated. A new upper shaft might be needed if the user is unable to control the mechanisms at the bottom of the trimmer. It is possible that the upper shaft might need to be replaced after years of normal wear and tear. Be sure the equipment is completely powered down and cooled off before attempting to repair an appliance. For more detailed instructions on how to install this specific part, see the owner's manual. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with different types of lawn equipment made by Husqvarna.

This part is a replacement D-handle nut. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part is intended for use as a replacement in a defective or misplaced nut in outdoor power equipment. This D-handle nut is a standard piece of hardware and thus has many functions. The D-handle enables this nut to be easily tightened and loosened by the user. Nuts can easily become worn, corroded, or lost, requiring replacement. Proper tools are not required to install this D-handle nut. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to install this D-handle nut, the appropriate owner's manual and equipment diagrams should be referred to. This D-handle nut is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with small engine outdoor power equipment that has been manufactured by Husqvarna, Poulan, and other brands.

This is a shield bracket for use with line trimmers. The bracket is used to help hold and support the debris shield to the trimmer shaft. If this piece is broken or not working properly, it means that the deflector will not be attached correctly, and the debris will not go where it should. Owners who find that the shield bracket has an issue will want to replace it as soon as possible.The shield bracket is made from durable metal, but it could still become damaged or corroded over time. If there is damage, the owners can make the simple replacement on their own. It is important that they remove the spark plug wire before making the installation, though. They should also wear gloves to keep their hands safe.The shield bracket is compatible with select models of line trimmers from Husqvarna, Weed Eater, Poulan, and Jonsered. The piece is sold individually. It is a genuine OEM replacement part that has been sourced directly from the manufacturer.

This is a genuine tapping screw replacement uses in certain models of outdoor lawn and garden equipment engines. This replacement screw is standard hardware on several units, and it has a variety of applications. Owners will need to consult their parts diagram for exact location and use. The screw is made of durable metal, but it is also exposed to constant heat and vibrations when the machine is in use, which can cause wear, damage, or even breakage over time. In some cases, the screw may become loose or get lost in the course of other repairs. In this case, a replacement will also be necessary. It's best to choose a genuine OEM screw like this model from Poulan. This screw is compatible with several blowers, saws, trimmers, and hedge trimmers from Poulan, as well as select units from Weed Eater, Jonsered, Paramount, and Husqvarna. A hex screwdriver or allen key will be required to replace this screw. Be sure to wear gloves and allow equipment to cool before working. This general use screw might be good to purchase in multiples to keep extras on hand in case of emergency. Each screw is sold as an individual part.

This part is a replacement spring. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. If the current spring is broken or defective, this part can be used as a replacement. It is intended for use with trimmers.The spring works by applying tension to the head of the trimmer. Over time and with regular use, springs can easily break or become eroded, requiring replacement. When working on or near an engine or blades, always ensure that the equipment is powered off and completely cooled down before attempting to undergo any repairs. For more accurate information on how and where to install this spring, the appropriate owner's manual and equipment diagrams should be referenced. This spring is suitable for use on a variety of trimmer models manufactured by Husqvarna and Poulan. It is a genuine OEM part and thus is made of high-quality, durable metal. Part sold individually.

This is the outer cover for a string trimmer housing. It clips into the bottom of the reel and secures it in place behind the central button. It’s constructed from a rubberized black plastic. This plastic is designed to be as durable as possible, while also flexing slightly when it’s under pressure. The cover serves two primary functions. It holds the reel in place and also acts as a mounting point for the central button. While it’s quite durable, it may eventually wear out due to regular use. A few scratches aren’t going to put a cover out of commission, but look for areas where the plastic has been worn through all the way. Replacing the cover is easy. Simply squeeze the old cover and pop it off the assembly. Position the new cover over the reel, then snap it into place. This cover is used primarily on Husqvarna string trimmers but is also used on some Poulan and Craftsman models. This is an OEM part sourced directly from Husqvarna, and it is sold individually.

This is the outer cover for a string trimmer housing. It clips into the bottom of the reel and secures it in place behind the central button. It’s constructed from a rubberized black plastic. This plastic is designed to be as durable as possible, while also flexing slightly when it’s under pressure. The cover serves two primary functions. It holds the reel in place and also acts as a mounting point for the central button. While it’s quite durable, it may eventually wear out due to regular use. A few scratches aren’t going to put a cover out of commission, but look for areas where the plastic has been worn through all the way. Replacing the cover is easy. Simply squeeze the old cover and pop it off the assembly. Position the new cover over the reel, then snap it into place. This cover is used primarily on Husqvarna string trimmers but is also used on some Poulan and Craftsman models. This is an OEM part sourced directly from Husqvarna, and it is sold individually.

This is a replacement knob for a trimmer. The plastic bump knob, which is connected to a spring, is used to secure the spool. A bump knob on a trimmer may get stuck or seized and will need a replacement. Before replacing the bump knob, remove the wire from the spark plug to avoid the accidental starting of the engine. Pull off the trimmer head housing and then use a flat head screwdriver to detach the old knob. Rotate it and then remove the component. Make sure the spring is in place then align the knob before rotating and snapping it in place. Take note that pulling the knob off may take extreme force when pulling. Some knobs are screw-mounted and a counterclockwise turn is necessary to unscrew it. This genuine OEM replacement part is sold individually and is compatible with specific trimmer models from Poulan and Weed Eater.