Parts for Weedeater TE400CXL TYPE 2: Driveshaft / Shield / Handle Parts

This part is a replacement D-handle nut. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part is intended for use as a replacement in a defective or misplaced nut in outdoor power equipment. This D-handle nut is a standard piece of hardware and thus has many functions. The D-handle enables this nut to be easily tightened and loosened by the user. Nuts can easily become worn, corroded, or lost, requiring replacement. Proper tools are not required to install this D-handle nut. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to install this D-handle nut, the appropriate owner's manual and equipment diagrams should be referred to. This D-handle nut is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with small engine outdoor power equipment that has been manufactured by Husqvarna, Poulan, and other brands.

This is a genuine OEM lawn and garden equipment screw that is used in various types of machines. It is a tapping screw that may have several applications depending on the exact equipment in question. A hex key screw is responsible for providing a secure hold for various components. It is made of durable metal, but also exposed to high heat and constant vibrations which can lead to wear, damage, or even breaking. The screw should always be replaced with an OEM replacement. This genuine OEM tapping screw is manufactured by Poulan. It is designed to be used in select outdoor power equipment units from the brand. It can also be used in compatible models from Paramount, Weed Eater, Jonsered, and Husqvarna. It fits trimmers, chain saws, and hedge trimmers from these brands. The tapping screw is sold individually and does not include any additional hardware or parts. A Torx screwdriver or hex key will be required to replace this tapping screw. Be sure to wear gloves when performing engine repairs and allow the machine to cool completely before starting work.

This trigger, used by Poulan and Weed Eater trimmers and edgers, controls the flow of gasoline into the carburetor so as to increase or decrease the speed of the rotating trimmer twine. The trigger is attached to the trimmer's throttle cable assembly. Though designed and used specifically by Weed Eater and Poulan, more than 85 different gasoline-powered devices use this trigger to regulate gas flow. While made of rugged plastic, the throttle trigger is often susceptible to more wear and tear than almost any other part of the trimmer. It sticks out away from the body of the device and thus is most susceptible. Being constantly squeezed, banged into other pieces of equipment, cement sidewalks, trees, landscaping barriers, and the like, throttle triggers can become bent, broken or irreparably disconnected from the throttle of the yard tool. Replacing the trigger begins with draining fuel from the trimmer's tank, then removing the throttle housing. Remove the throttle cable from the old trigger and install it in the new trigger. Replace the throttle housing. When replacing the trigger, it's best to use a genuine OEM replacement part, like this one, machined to be identical to the original.

This replacement part is a throttle cable assembly. This is a genuine replacement part made by Husqvarna. This cable is used to connect the throttle to the user area so that the operator is able to control certain settings during use. A new throttle cable assembly might be needed if the user is unable to control the throttle. The wires in the throttle cable can become stripped or worn down. If this is the case, it is recommended that it be replaced right away. Be sure that the engine is turned off before working with wires and other objects connected to the engine. This throttle cable assembly is also sold individually and is sourced directly from the manufacturer. This part is a genuine OEM replacement part to ensure proper fit and long-lasting use.

This replacement part is a line guide, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by Husqvarna. This line guide is small but aids in creating straight lines while cutting the grass in many different lawn mowers. A new line guide might be needed if the user notices the current one is not working properly. If the cutting lines of grass are not as straight as normal there might be an issue with the line guide inside of the machine. Be sure to wear working gloves while replacing this part as it is typically found near the blades of the appliance. This small part is sold as a single piece. This part is a genuine OEM part sourced directly from the manufacturer. Be sure to reference the specific owner's manual for more information on how to replace this part.

This is a cap assembly designed for gas string trimmers. The cap assembly is installed at the base of the trimmer's drive shaft, over the spool real. It is responsible for the advancement of the trimmer line in the spool when hit against the ground and also serves to protect the spooled trimmer line from dust and debris. The cap is made of durable plastic and is meant to absorb shock from the ground. However, over time, the threads on the cap's interior may become worn out. Blows from hard surfaces like asphalt and concrete may cause the cap to weaken and even break. A cap that fails to remain in place or is significantly damaged needs to be replaced.The installation of a new cap assembly is easy. First, remove the old cap assembly. The use of an adjustable wrench or vice grips might be necessary depending on the old cap's threading. Once the old cap is removed, then simply screw the new one on, making sure it firmly fastened.This is an OEM part sourced directly from the manufacturer. It is sold individually. The cap assembly is compatible with Craftsman and Husqvarna trimmer models.

This replacement part is an assembly wire guard. This part is commonly found in line trimmers or edgers and is responsible for assisting the user in performing an accurate cut during any job. A new assembly wire guard might be needed if the current one is missing or damaged in any way. This can be from wear and tear after years of normal use or from a single incident that may have caused it to no longer work properly. If the assembly has become dented, bent, or cracked, it might be time to replace it. This is a genuine OEM replacement part manufactured by Husqvarna. This part is sold individually.

This part is a replacement D-handle nut. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part is intended for use as a replacement in a defective or misplaced nut in outdoor power equipment. This D-handle nut is a standard piece of hardware and thus has many functions. The D-handle enables this nut to be easily tightened and loosened by the user. Nuts can easily become worn, corroded, or lost, requiring replacement. Proper tools are not required to install this D-handle nut. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to install this D-handle nut, the appropriate owner's manual and equipment diagrams should be referred to. This D-handle nut is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with small engine outdoor power equipment that has been manufactured by Husqvarna, Poulan, and other brands.