Parts for Poulan PP136: Driveshat / Shield / Handle Parts

This replacement part is a screw. It is a genuine replacement part made by Husqvarna. Screws are small yet very important to the overall operations of many different machines and appliances. Screws are able to hold other parts in place and secure so that everything can operate smoothly. A new screw might be needed if the user notices that the current ones are damaged or missing. It is possible that screws become stripped or lodged over time and must be replaced. The repair should be fairly easy, only requiring a screwdriver or pliers if the previous screw is stuck. Be sure the engine is completely powered down before starting a repair. This screw is sold individually. Be sure to purchase the correct amount as many appliances require more than one. This is a genuine OEM replacement part sourced directly from the manufacturer.

This authentic OEM replacement on/off switch is a safety measure that manufacturers install to prevent the chainsaw or trimmer from starting before the operator is ready. It also allows the operator to stop their appliance at a moment's notice if they lose control of it. The on/off switch is located in or near the handle of the appliance and must be in the on position for the appliance to start. If hit to the off position, the appliance will immediately stop running. Switches can slowly wear out over time due to repeated use. When it wears out, the switch will no longer give the same amount of resistance and may be tripped more easily. This can be frustrating as it means that the operator would have to continually restart their appliance. To replace the switch, use a screwdriver to access the handle interior and detach the wiring from the old switch. Install the new part and reassemble. This switch is a high-quality replacement part for Craftsman chainsaws and trimmers, and as such, it comes sourced directly from the original manufacturer. This part ships individually.

This replacement part is a handle clamp. This is a genuine replacement part made by Husqvarna. This part works with the handle of many lawn mowers and is able to maintain the functions of the handle itself. A new handle clamp might be needed if the current one has become damaged. This can be due to normal wear and tear and should be replaced if this is the case. If the functions of the handle are no longer working properly, it might be due to a malfunctioning handle clamp. Work gloves are recommended to ensure safety during the repair job. Be sure the engine is completely shut down during this repair. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This part is a replacement D-handle nut. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part is intended for use as a replacement in a defective or misplaced nut in outdoor power equipment. This D-handle nut is a standard piece of hardware and thus has many functions. The D-handle enables this nut to be easily tightened and loosened by the user. Nuts can easily become worn, corroded, or lost, requiring replacement. Proper tools are not required to install this D-handle nut. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to install this D-handle nut, the appropriate owner's manual and equipment diagrams should be referred to. This D-handle nut is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with small engine outdoor power equipment that has been manufactured by Husqvarna, Poulan, and other brands.

This replacement part is a screw. It is a genuine replacement part made by Husqvarna. Screws are small yet very important to the overall operations of many different machines and appliances. Screws are able to hold other parts in place and secure so that everything can operate smoothly. A new screw might be needed if the user notices that the current ones are damaged or missing. It is possible that screws become stripped or lodged over time and must be replaced. The repair should be fairly easy, only requiring a screwdriver or pliers if the previous screw is stuck. Be sure the engine is completely powered down before starting a repair. This screw is sold individually. Be sure to purchase the correct amount as many appliances require more than one. This is a genuine OEM replacement part sourced directly from the manufacturer.

All gasoline-powered trimmers must have throttle controls that increase the amount of gasoline flowing into the carburetor. As the amount of fuel increases and the engine revolutions increase, the clutch engages the spool and the trimming line begins to turn. The throttle trigger assembly is quite durable. However, it has several appendages and is required to be under constant pressure when in use. If any of the design parts fail, the trigger unit must be replaced or the trimmer cannot be used. To replace the throttle trigger, open the housing and disconnect the throttle cable from the old trigger. It's easy to see where the new trigger will fit in the housing because the screw holes will line up perfectly with the holes in the new throttle trigger. The throttle cable will fit into one slot on the new trigger and a spring opposite the slot will hold the trigger unit at the proper angle as the housing is replaced. This new throttle trigger is an OEM replacement part, made to the same exacting specification as the original. This throttle control is designed by Craftsman and used on most of their trimmers. It is also compatible with a few other manufacturers' trimmers, including Poulan and Husqvarna.

This replacement part is an upper shaft and is intended for use in a variety of lawn equipment. This is a genuine replacement part made by Husqvarna. This upper shaft is typically found in hedge trimmers and is an important part to this appliance. This part is able to connect the power source from the top of the appliance to the trimmer head at the bottom so that the drive mechanisms is activated. A new upper shaft might be needed if the user is unable to control the mechanisms at the bottom of the trimmer. It is possible that the upper shaft might need to be replaced after years of normal wear and tear. Be sure the equipment is completely powered down and cooled off before attempting to repair an appliance. For more detailed instructions on how to install this specific part, see the owner's manual. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with different types of lawn equipment made by Husqvarna.

This part is a replacement D-handle nut. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part is intended for use as a replacement in a defective or misplaced nut in outdoor power equipment. This D-handle nut is a standard piece of hardware and thus has many functions. The D-handle enables this nut to be easily tightened and loosened by the user. Nuts can easily become worn, corroded, or lost, requiring replacement. Proper tools are not required to install this D-handle nut. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to install this D-handle nut, the appropriate owner's manual and equipment diagrams should be referred to. This D-handle nut is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with small engine outdoor power equipment that has been manufactured by Husqvarna, Poulan, and other brands.

This is a shield bracket for use with line trimmers. The bracket is used to help hold and support the debris shield to the trimmer shaft. If this piece is broken or not working properly, it means that the deflector will not be attached correctly, and the debris will not go where it should. Owners who find that the shield bracket has an issue will want to replace it as soon as possible.The shield bracket is made from durable metal, but it could still become damaged or corroded over time. If there is damage, the owners can make the simple replacement on their own. It is important that they remove the spark plug wire before making the installation, though. They should also wear gloves to keep their hands safe.The shield bracket is compatible with select models of line trimmers from Husqvarna, Weed Eater, Poulan, and Jonsered. The piece is sold individually. It is a genuine OEM replacement part that has been sourced directly from the manufacturer.

The spool retainer replacement is used for trimmers and pruners. It helps to secure the spool in the hub assembly of the machines, so it will hold the line or string. Without a functioning spool retainer, it would be impossible to use the machine properly. The spool retainer can start to wear out over time and no longer function correctly. It might become broken, as well. Replacing the retainer is essential, and it is an easy replacement to make. The spool can be pressed into the hub assembly and it releases just as easily. This is a genuine OEM replacement part that is sold individually. It works with certain makes and models of pole pruners and trimmers. Compatible brands include Craftsman, Husqvarna, Weed Eater, Poulan, and Poulan Pro. When buyers are choosing the new spool retainer, they should ensure they are buying the correct replacement part.