Parts for Ge DPVH880EJ0WW: 06 - Drum Parts

Mounting screw for dryer drum support and internal components. Replaces lost, stripped, or damaged screws during repairs. Package of 12 screws included.

This hex washer-head screw secures dishwasher components like brackets, shields, and panels. Replacing a stripped or missing screw restores a tight fit and helps prevent vibration, rattling, and loose parts during operation.

• Fastens parts where a #10-16 x 1/2-inch hex washer-head screw is specified
• Secures brackets, panels, and assemblies to the tub or frame
• Helps resolve symptoms like loose panels, vibration, or rattling noises
• Restores proper hold when the original screw is stripped, missing, or damaged

• Disconnect power and shut off water to the dishwasher before servicing
• Match length and thread to the original; replace screws one at a time to maintain alignment
• Start threading by hand to avoid cross-threading; tighten snugly—do not overtighten, especially into plastic
• Verify no wires or hoses are pinched before reassembly

• Size: #10-16 x 1/2 inch
• Head: hex washer-head
• Type: AB tapping screw

This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.

• Fastens brackets, covers, and sheet-metal panels as specified in the parts diagram
• Restores proper fit when an original screw is missing, stripped, or damaged
• Helps eliminate rattling or vibration from loose hardware
• Keeps components safely in place during operation

• Disconnect power to the appliance before servicing
• Match length, head style, and thread to the original; install in the same location/quantity
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten, especially into plastic or thin sheet metal

Drum heat deflector directs hot air evenly inside your dryer. Replace if cracked, warped, or missing to restore proper airflow and protect drum.

Hi-limit thermostat. L210.

The Inlet Control Thermistor is an OEM part for GE dryers. It monitors and regulates the temperature of the incoming air to ensure optimal drying performance. This thermistor sends temperature readings to the dryer's control board, which adjusts the heating element accordingly to maintain the desired temperature throughout the drying cycle.

You should replace this inlet control thermistor if it becomes faulty or fails to provide accurate temperature readings. Common causes of a bad thermistor include electrical failures, damage from overheating, or wear and tear from regular use.

Symptoms of a bad inlet control thermistor include:

• Dryer not heating properly
• Overheating or uneven drying
• Dryer shutting off prematurely
• Error codes related to temperature issues

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Supports and stabilizes the dryer drum for smooth rotation. Replace if shaft is worn, bearing is damaged, or drum wobbles or sinks at the rear.

Ceramic terminal insulator protects heating element electrical connections in dryers. Replace if cracked, broken, or missing to restore secure insulation.

Bonds dryer cabinet to ground point for safe operation. Replace if damaged, broken, or missing to restore proper electrical grounding and reduce shock risk.

A replacement dampening band that cushions the washer tub and helps reduce vibration and noise during spin cycles. Restores smoother, quieter operation when the tub is rubbing or moving excessively. What it does:

• Wraps around/under the outer tub to absorb shocks and dampen tub movement during spin
• Reduces vibration, banging, and harsh impacts that occur with worn or damaged dampeners
• Helps keep the tub centered and prevents metal-to-metal contact
• Common symptom: washer vibrates, rocks, or makes loud knocking during spin

• One dampening band

• Disconnect power and water supply before starting any repair
• Access typically requires removing the washer cabinet or top panel; follow model-specific instructions
• Inspect surrounding suspension components and mounting points for wear; replace if damaged
• After installation, run a short spin cycle with no load to reduce vibration

This is a small screw, and it is made for dryers, washers, and washer dryer combos. This is a genuine replacement part made by General Electric. Screws are common in these appliances and can cause many difficulties if they become loose, damaged, or missing.A new screw might be needed if there are areas in the appliance that seem off balance or not level. Another way to tell if a new screw is needed is if there are parts in the appliance that are loose or falling off. This is common over many years of normal use as the shaking of washers and dryers can eventually lead to loose screws. Be sure the washer or dryer is completely off before attempting to replace any screws.This is an OEM part sourced directly from the manufacturer. It is sold individually and is compatible with washers, dryers, and washer dryer combos made by General Electric.

The bearing retainer secures the drum bearing assembly in your dryer. Replace if cracked, broken, or worn to restore proper structural support.

Supports the rear dryer drum for smooth, quiet rotation. Replace if you hear squeaking, screeching, or thumping during cycles. Verify fit with your model.

The O Ring is an OEM part for GE dryers, creating a tight seal in different components for efficient operation. This small part prevents air leaks that can impact drying performance, made from quality materials to withstand high temperatures and frequent use

Causes of a faulty O Ring in a dryer may stem from heat exposure, regular wear and tear, or chemical damage. This can result in reduced elasticity, cracks, or breaks, impacting the seal.

Symptoms of a bad O Ring in your dryer include:

• Reduced efficiency in drying, as air leaks can affect the dryer's ability to maintain the correct temperature.
• Unusual noises stemming from air escaping through the compromised seal.
• Potential for small leaks or condensation within the dryer's internal components, leading to moisture issues.

This genuine GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.