Parts for Ge PTD90GBST0WS: Drum Parts

Secures dryer panels and internal components to the cabinet frame. Replace if screw is stripped, missing, or loose to prevent vibration and rattling.

If your dryer clothes are rubbing or tumbling unevenly, a worn drum assembly may be the cause. This rotating tub holds and tumbles laundry for efficient drying.

Fix melted plastic or goop marks on clothes with a new dryer heat diffuser. Replaces damaged diffuser that causes staining. DIY repair with 3 screws.

Dryer won't heat or overheats? This high limit thermostat monitors temperature and cuts power when heat exceeds safe limits. Moderate DIY repair.

Dryer not heating or overheating? This thermostat regulates temperature to prevent damage. Common DIY repair takes 30-45 minutes with basic tools.

The Inlet Control Thermistor is an OEM part for GE dryers. It monitors and regulates the temperature of the incoming air to ensure optimal drying performance. This thermistor sends temperature readings to the dryer's control board, which adjusts the heating element accordingly to maintain the desired temperature throughout the drying cycle.

You should replace this inlet control thermistor if it becomes faulty or fails to provide accurate temperature readings. Common causes of a bad thermistor include electrical failures, damage from overheating, or wear and tear from regular use.

Symptoms of a bad inlet control thermistor include:

• Dryer not heating properly
• Overheating or uneven drying
• Dryer shutting off prematurely
• Error codes related to temperature issues

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Plastic baffle that installs inside the dryer drum to lift and tumble clothes. Replace if cracked, broken, thinning, or missing vanes that may mark fabrics.

Fix electrical grounding issues with this dryer ground strap assembly. Restores proper chassis grounding to reduce shock risk. Simple repair for worn connections.

Supports and stabilizes the dryer drum for smooth rotation. Replace if shaft is worn, bearing is damaged, or drum wobbles or sinks at the rear.

This combustion chamber is the metal housing that surrounds and directs the gas burner flame in a gas dryer, protecting surrounding components and guiding combustion for reliable heating performance. What it does

• Houses and aligns the burner assembly and igniter to ensure proper flame direction
• Channels exhaust and combustion flow away from sensitive parts
• Helps prevent heat damage to the dryer cabinet and nearby components
• Symptoms this can fix: poor or uneven heating, burner flame misalignment, or burner noise from loose housing

• One combustion chamber housing

• Turn off and unplug the dryer and shut off the gas supply before servicing
• Inspect and replace any damaged gaskets or mounting hardware for a proper seal
• Use basic hand tools; avoid bending or deforming the chamber during installation

Transition duct connects your dryer to the wall vent exhaust system. Replace if cracked, torn, or damaged to restore proper airflow and venting.

This gas diffuser directs and evens the burner flame for reliable cooking performance. It helps stabilize heat distribution so burners light and heat more consistently across cookware. What it does:

• Spreads and evens gas flame to reduce hot spots and uneven cooking
• Helps stabilize burner ignition and maintain consistent flame shape
• Prevents direct flame contact with surrounding components
• Addresses symptoms like uneven heating, unstable flame, or partial burner operation

• One gas diffuser

• Turn off the gas supply and unplug the appliance before servicing
• Use basic hand tools; avoid overtightening or distorting the part
• If corrosion or sealed fasteners are present, replace affected hardware and check surrounding components

Flame deflector for gas dryers. Directs burner flame evenly during heating cycles. Replace if cracked, warped, or missing to restore proper operation.

The Flame Sensor is an OEM part for GE dryers. This part detects the presence of a flame in gas dryers, ensuring that the gas ignites properly for safe and efficient drying.

Causes of a bad flame sensor can include regular wear and tear, carbon buildup from the gas flame, or electrical malfunctions.

Symptoms of a bad flame sensor include:

• The dryer not heating or taking longer to dry clothes
• The dryer shutting off unexpectedly during a cycle
• The igniter glowing but not igniting the gas
• Error codes related to heating or ignition issues

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.