Parts for HLP141E: Dryer Parts

A small replacement housing screw that secures appliance panels and brackets, restoring proper fit and preventing rattles or loose panels. Fits common appliance housings where a short ST4 x 12 self-tapping screw is required. What it does:

• Fastens housing panels, trim, or internal brackets to maintain proper alignment and reduce vibration
• Replaces missing or damaged screws that cause loose or rattling panels
• Works with sheet metal and plastic mounting points designed for ST4 thread size
• Small, low-profile head designed for appliance interiors

• One housing screw (ST4 x 12)

• Disconnect power before servicing the appliance and work on cool surfaces
• Use the correct screwdriver or bit to avoid stripping the head
• Install gently and avoid overtightening to prevent thread or panel damage

The Capacitor is an OEM part for GE dryers. It is part of the dryer's motor system, providing an extra boost of power to start the motor and keep it running smoothly during operation.

A bad capacitor can lead to motor-related issues and dryer malfunctions. Causes of a bad capacitor can include electrical surges, overheating, or general wear and tear over time.

Symptoms of a bad capacitor include:

• Dryer not starting or having difficulty starting
• Motor running erratically or making unusual noises
• Dryer drum not spinning
• Dryer taking longer than usual to dry clothes

Replace your faulty or damaged Capacitor with this genuine OEM GE part to restore your dryer. 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.
 

This refrigerator door gasket creates a tight seal around the door edge to help maintain proper temperature and reduce energy loss. A worn gasket can let cold air escape and cause the compressor to run more often. What it does:

• Seals the refrigerator door to keep cold air inside and warm air out
• Helps prevent moisture intrusion and reduces frost buildup in the fresh-food area
• Supports consistent interior temperature for better food preservation
• Common symptom of failure: visible gaps, torn or compressed seal, or frequent running compressor
• Replacing a damaged gasket often resolves leaking, frost, or cooling inconsistency

• Disconnect power before beginning any repair to avoid electric shock
• Remove the old gasket and clean the door flange thoroughly before installing the new seal
• Fit the new gasket into the door channel, working around the perimeter for an even seal; warm the gasket gently if needed to reshape

If your dryer won't heat or overheats, the thermostat may need replacement. This temperature control part regulates heat cycles for safe, effective drying.

Dryer not heating or taking too long to dry clothes? This PTC heating element restores proper heat output. Moderately easy DIY repair for most models.

If your dryer won't start or the drum won't turn, the drive motor may have failed. This motor powers the drum and blower. Moderate DIY repair, 1-2 hours.

The Lint Filter Cover is an OEM part for GE electric dryers. It securely houses the crucial lint screening component located inside the dryer drum.  

Symptoms of a bad lint filter cover include:

• Cracks, breaks or holes compromising the seal around the lint filter
• Loose, missing, or improperly closing attachment points
• Excess lint buildup bypassing the filter into the surrounding cabinet

Causes involve dried-out or fatigued clips, hinges, and seals from repeated use over cycles. Cover failure risks fire hazards from obstructed airflow.

This GE OEM replacement lint filter cover ensures safe, snug-fitting protection of the integral screen. Compatible with some Hotpoint and Kenmore dryers as well, it maintains ventilation and fire prevention. 

Belt pulley mounts to the dryer motor shaft to drive the drum belt. Replace if pulley is cracked, worn smooth, wobbling, or causing belt slippage.

Dryer drum belt wraps around the drum to rotate it during cycles. Replace if you hear squealing, the drum won't turn, or see cracks. Confirm fit by model.

Dryer lint filter traps debris to maintain airflow and prevent fire hazards. Replace if torn, warped, or clogged. Confirm fit with your model number.

Dryer door gasket creates an airtight seal to maintain proper drying temperature. Replace if torn, cracked, or causing heat loss. Verify fit with your model.

Seals around your dryer lint screen to block lint and improve airflow. Replace when worn or torn to restore proper drying. Verify fit with your model.

If your dryer door won't lock or stay closed during cycles, this door lock motor and switch assembly restores proper latching and operation. Direct fit.