Parts for Electrolux ELFE4222AW: Drying System Parts

Leveling leg for dryers and laundry centers. Installs at the base corner to adjust height and stabilize the unit. Replace if cracked or missing.

Dryer cover panel that installs on the exterior cabinet. Replace this part if your original is cracked, broken, discolored, or missing during repairs.

Door gasket seal for dryers creates an airtight seal around the door opening. Replace if torn, cracked, or allowing air leaks. Confirm fit with your model.

This replacement refrigerator door panel restores the exterior surface and structural fit of the appliance, helping protect internal components and maintain proper closure. It's a direct-fit part meant to replace a damaged or dented door panel. What it does

• Replaces a dented, cracked, or cosmetically damaged refrigerator door panel
• Restores proper alignment so the door closes and seals consistently
• Protects internal insulation and components from further damage
• Helps maintain appearance and resale value of the appliance

• One replacement refrigerator door panel

• Disconnect power before beginning any repair and work on a clean, stable surface
• You may need to transfer hinges, handles, gaskets, and internal trim from the old door
• Larger doors can be heavy or awkward — have a second person assist to avoid injury or damage
• If the door includes glass or electrical components, handle with care and follow OEM instructions for reassembly

Control knob for dryer cycle selection and temperature settings. Replaces cracked, broken, or missing knobs. Installs on control panel.

This condenser coil removes heat from the refrigerant so the refrigerator can maintain proper cooling. Replaces a worn or damaged condenser to help restore normal cooling performance and compressor efficiency. What it does:

• Condenses refrigerant from a gas to a liquid by dispersing heat to surrounding air.
• Helps the compressor run at correct temperatures and prevents overheating.
• Common symptoms it can address: refrigerator not cooling well, compressor running constantly, or unusually warm cabinet.
• Works with the appliance's condenser fan and compressor to complete the cooling cycle.

• Disconnect power to the appliance before beginning any work.
• Avoid bending or damaging coil fins; handle the assembly carefully.
• Some installations may require removing the back service panel and disconnecting mounting brackets; retain all fasteners.

This replacement refrigerator door handle restores a secure grip and smooth opening for a damaged, cracked, or broken handle. Durable molded construction matches the original fit to keep the door easy to open and close. What it does

• Provides a sturdy grip to open and close the refrigerator door
• Replaces cracked, chipped, or loose door handles that affect operation
• Restores original appearance and user control at the door edge
• Helps prevent further damage from using a compromised handle

• Disconnect power to the appliance or turn off water before starting.
• Remove any trim or end caps and unfasten mounting screws to swap the handle.
• Support the door while removing/installing the handle to avoid stress on the hinges.
• Use appropriate hand tools and avoid overtightening fasteners to prevent cracking.

Replace your dryer door seal gasket to prevent heat loss and improve drying efficiency. Install when you notice air leaks or lint escaping. Confirm fit with your model number.

Fix a dryer that won't tumble or makes squealing noises with this drive belt. Connects the motor to the drum for proper rotation. DIY-friendly repair.

Dryer won't start or drum won't turn? This drive motor assembly powers the drum and blower. Moderate difficulty repair, typically 1-2 hours.

This is a water drain pump assembly used in condensation-style dryers to remove collected moisture from the internal reservoir. It pumps water from the collection tank through the drain hose so the dryer can continue operating efficiently. Replace this pump if the dryer is leaking water, the condensation tank overflows, or you hear the pump running but water is not being evacuated.

This is a dual-wattage heating element assembly rated at 240V with 1900W and 700W outputs. It generates the heat needed to dry clothes inside the dryer drum. Replace this part if your dryer is not producing heat, takes too long to dry clothes, or shuts off prematurely due to insufficient heating.

This is a micro float switch assembly located near the dryer's condensate pump or drain system. It detects the water level and signals the pump to activate when condensation accumulates. Replace this switch if the dryer fails to pump out collected water, if water overflows from the pump reservoir, or if the dryer stops mid-cycle due to a faulty water level signal.

Replace worn drum support bushings to restore smooth, quiet drum rotation and eliminate wobble or scraping noises. Confirm fit with your model number.

Dryer drum felt seal creates an airtight barrier between the drum and bulkhead. Replace if worn, torn, or causing squeaking noises. Verify fit with your model.

Fix weak airflow or overheating dryer issues with this blower wheel. Restores proper air circulation through the drum and exhaust system. DIY-friendly repair.

Dryer overheating or shutting off mid-cycle? This cooling fan circulates air to prevent thermal overload. Moderate DIY repair, typically 30-45 minutes.

This is a mesh lint filter that fits inside the dryer's lint trap housing to capture lint and debris during drying cycles. It helps maintain proper airflow through the dryer drum for efficient drying and reduces fire risk. Replace this filter if it is torn, warped, has holes in the mesh, or if your dryer is taking longer than usual to dry clothes.

If your dryer overheats or won't heat properly, the temperature probe may have failed. This sensor monitors internal temperature for accurate heating.

Dryer won't start, heat, or complete cycles? The electronic control board manages all dryer functions. Moderate DIY repair with proper diagnostics.

This electrical wiring harness connects control components to power and signals so your appliance's controls and functions receive consistent electrical routing. It restores proper electrical connections and helps resolve intermittent or failed control behavior. What it does:

• Routes power and signal lines between control board, switches, and components
• Restores lost or intermittent electrical connections that can cause controls to stop responding
• Helps fix symptoms such as no power to certain circuits, intermittent operation, or controls that do not respond
• Maintains organized wiring routing to prevent chafing or loose connections

• Disconnect power to the appliance before starting any work to avoid shock
• Match connector shapes and wire colors; do not force connectors together
• Secure harness routing with existing clips or fasteners to prevent contact with sharp edges or moving parts