Electrolux Range / Cooktop / Oven Parts

Secures components inside your range or oven. Replace this bracket if it's bent, broken, or missing to restore proper mounting, alignment, and stability.

Fixed natural gas orifice that meters fuel to cooktop or range burners. Replace worn, damaged, or incorrect orifices to restore proper flame size.

Oven not heating to set temperature or heating too slowly? This thermostat controls oven temperature cycling. Test for continuity to diagnose the issue.

Microwave won't turn on or has no power? This fuse and holder assembly restores overcurrent protection when a blown fuse interrupts operation.

The Latch is an OEM replacement part for Frigidaire built-in microwaves. Securely mounted to the top interior section of the microwave cavity door, the positive-locking latch holds the door safely shut during operation. Crafted from corrosion-resistant materials for extended use, the latch handle withdraws the hook mechanism with a simple pull to conveniently access food within.

Symptoms of a bad latch include:

• The microwave door popping or falling open unexpectedly  
• Difficulty closing or fully engaging the secure latch hook 
• Wear signs like loose mounting points or a worn handle

Causes can involve repeated opening/closing cycles gradually loosening mounting fixtures, or parts rendered ineffective by moisture intrusion over time.

Replacing this Frigidaire OEM latch prevents potential microwave door opening during cooking cycles. Compatible with Electrolux, Gibson, Kelvinator, and Kenmore built-in models.

Size: 6-20 x 0.312 inch.

Seals the gap between burner and cooktop to prevent spills from leaking underneath. Replace when seal becomes discolored, cracked, or loses flexibility.

Replacement gasket that seals around surface burners to prevent spills from entering the cooktop cavity. Replace when hardened, cracked, or torn. Confirm fit with your model number before ordering.

Replacement mounting screw for electric and gas ranges. Secures panels, brackets, trim, and oven base plates. Replaces missing, stripped, or corroded fasteners.

Protective shield that covers internal components on your gas range. Replace if cracked, broken, or missing to restore protection from debris and moisture.

Replaces cracked, broken, or scratched glass cooktop surface on electric ranges. Provides the flat cooking area and restores appearance and fit.

This ignitor orifice assembly delivers and meters gas to the oven/range ignitor so burners light reliably. Replace a damaged or clogged assembly to restore consistent ignition and proper burner lighting on compatible gas appliances. What it does:

• Routes and meters gas flow to the ignitor so the burner can light
• Supports consistent ignition timing for oven and range burners
• Commonly used when an oven won't light, has weak or uneven flames, or ignition failures occur
• Helps prevent gas leaks by providing a secure connection when installed correctly

• Disconnect power and shut off the gas supply before starting any work
• Only install on compatible appliances; follow the OEM instructions
• Hand-tighten connections and check for leaks with a soapy-water solution after restoring gas

This is a normally open cooling fan thermostat that activates the oven's cooling fan when internal temperatures reach a set threshold. It helps regulate airflow to protect surrounding cabinetry and electronic controls from excessive heat. Replace this thermostat if the cooling fan fails to turn on during or after oven use, or if the fan runs continuously without shutting off.

This wiring harness routes power and signals between a refrigerator's control components and electrical devices, restoring reliable electrical connections for operation and controls. It replaces a damaged or broken harness to help regain normal appliance function. What it does:

• Connects control board, sensors, lights, and other electrical components to provide power and signal paths
• Replaces frayed, burnt, or damaged wiring that can cause intermittent or complete loss of function
• Helps resolve symptoms such as lights or dispenser not working, erratic controls, or failure of specific features tied to wiring
• Restores proper connector fit and secure electrical contacts when original harness pins or wires are compromised

• One wiring harness as shown

• Always disconnect power to the appliance before starting any repair
• Match connector shapes and wire colors to the original harness; route along original paths and secure with clips or ties
• Inspect mating connectors and control board terminals for damage before installing the new harness

Main electronic control board for electric cooktops. Manages user interface and appliance functions. Replace if board is damaged, burnt, or unresponsive.

Replacement machine screw used to secure appliance panels and internal components, restoring a stable fit and reducing rattling. Matches a 10-32 thread with a 17/32-inch length for original fastener locations. What it does:

• Fastens panels, trim pieces, and internal brackets; a missing or damaged screw can cause loose panels or rattling noises.
• Secures knobs, control housings and small assemblies to prevent wobble or misalignment.
• Restores proper fit for components so doors and access panels sit evenly and function reliably.

• Disconnect power (unplug or shut off circuit) before accessing components.
• Use the correct driver and tighten by hand; avoid overtightening to prevent stripped threads or cracked plastic.
• Keep any original washers or clips and reinstall them with the screw.