Electrolux Range Rack Or Shelf

The Frigidaire Oven Rack is an OEM part for Frigidaire ranges and wall ovens. It provides an elevated surface for baking sheets, casserole dishes, and other cookware during the heating process. The rack measures approximately 24 inches wide by 16 inches deep.

Causes of a bad oven rack could be cracks, bends, or breaks that develop from repeated expansion and contraction during heating. Normal wear from years of use can impact the integrity of welds or supports.

Symptoms of a bad Oven Rack include:

• Difficulty sliding the rack in or out
• The rack not sitting level or securely in the oven
• Warping or bending of the rack
• Rust or discoloration on the rack surface

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This oven rack provides a sturdy, level surface for cookware inside your range or wall oven. Replace a bent, rusted, or missing rack to restore safe support and smooth, reliable placement at the proper cooking height.

• Slides into the oven's side rails to hold pans at the desired level
• Supports bakeware evenly and maintains proper clearance for airflow
• Replace when the rack is warped, corroded, flaking, or difficult to slide
• Common symptoms include wobbling, not sitting level, or a missing safety stop

• Allow the oven to cool completely; wear gloves to protect from sharp edges
• Insert the rack with the stop end toward the rear; engage both side rails evenly
• Push in until the rear stops seat; the rack slides freely and sits level
• To remove, pull to the stop, lift the front slightly, then pull straight out

This replacement air fry tray lets your oven's air-fry function hold and crisp foods safely on the oven rack. It restores the manufacturer-intended tray used with Peregrine-series air fry ovens for even airflow and easy cleanup. What it does

• Holds food above the oven surface so hot air can circulate for air-frying and crisping.
• Designed to work with the oven's air-movement system to help promote even browning.
• Replaces a bent, warped, cracked, or missing air-fry tray that prevents proper use of the air-fry feature.
• Helps contain drips and crumbs for easier cleanup when roasting or air-frying.

• One air fry tray (Peregrine) as shown.

• Slide the tray onto the oven rack in the same orientation as the original; no tools usually required.
• Allow the oven to cool and disconnect power before removing the old tray or installing the new one.
• Inspect oven racks and supports for damage before use; do not use if warped or compromised.
• Hand wash or follow manufacturer care instructions; avoid abrasive cleaners that could damage the finish.

This wire oven rack restores stable, even support for cookware and bakeware inside the oven cavity so you can cook and roast with correct clearance and airflow. Designed to replace worn, bent or missing oven racks. What it does

• Provides a stable surface for pots, pans and baking sheets during cooking and roasting
• Restores correct rack spacing and airflow for even heating
• Replaces bent, rusted or warped racks that no longer slide or support cookware
• Compatible with standard oven side-rail grooves for easy placement

• One wire oven rack

• Slide the rack into the desired oven rail position until it seats securely; no tools required for typical installations
• Allow the oven to cool completely before removing or installing the rack to avoid burns
• Clean rack per manufacturer instructions; avoid abrasive cleaners that can damage finish
• If the rack is difficult to slide, inspect oven rails for damage or obstructions before forcing

This oven rack support holds an oven rack in the correct position so cookware stays level while you cook. Replacing a damaged support restores stable rack operation and prevents racks from slipping or tilting. What it does:

• Secures the oven rack at the correct height so pans and bakeware sit level.
• Replaces cracked, bent, or broken supports that allow racks to sag or fall.
• Helps stop racks from binding or catching when you slide them in and out.
• Works as a direct-fit service part where listed by the manufacturer.

• Allow the oven to cool and disconnect power before starting any repair.
• Remove oven racks and inspect mounting area before installing the new support.
• Most installations are straightforward; align the support and engage it into the oven side wall or track as shown in the service diagram.

This glass shelf replaces a cracked or worn interior shelf to restore stable, easy-to-clean storage space in your refrigerator. Tempered glass provides a flat surface for food containers and helps keep items organized and visible. What it does:

• Provides a sturdy, level surface for storing food, containers and leftovers
• Replaces broken, chipped or scratched shelves that can trap spills or block airflow
• Helps maintain interior organization so items are easier to find
• Smooth glass surface wipes clean quickly to remove spills and crumbs

• One tempered glass refrigerator shelf

• Remove food and any loose items from the shelf area before installing
• Slide shelf into the existing support rails or brackets until it sits securely
• Handle glass carefully and wear gloves to avoid injury from edges