Parts for Mtd 11A-41M9006 / 2009: Engine Assembly 5P65m0b Parts

Hex screw that secures components on lawn mowers, snow throwers, tillers, and chippers. Replace if stripped, rusted, missing, or damaged during repair.

This is a recoil starter assembly for lawn and garden power equipment. When the recoil starter rope is pulled, this causes the spark which starts the engine.A new recoil starter assembly will be needed if the recoil or pulley system has broken. The rope may become broken or frayed and the plastic on the pulley could crack. If the rope becomes loose and there is no tension when it is pulled, then a new recoil starter assembly will be needed.This part is a genuine MTD part and is an OEM part sourced directly from the manufacturer and it is sold individually. It is used on engines, lawnmowers, lawn tractors, and log splitters that are manufactured by MTD, Yard-Man, Yard Machines, Cub Cadet, Husky, and Troy-Bilt.

Starter rope won't retract after pulling? This recoil pulley and spring assembly fixes rope retraction issues on mowers and small engines. Direct fit.

Maintains proper clearance between engine shroud components. Replace if cracked, broken, or missing to ensure correct spacing and airflow around the engine.

Fastener nut for outdoor power equipment. Secures components in place during operation. Replace if stripped, corroded, or missing to restore assembly.

This brake assembly bolt is a genuine MTD part that is manufactured to be a replacement part for lawn tractors, push walk-behind mowers, log splitters, trimmers, chippers, shredders, and other engines.On engines such as these, the brake assembly helps work the brake, which stops the engine and any forward motion. It is not abnormal for brake assembly bolts to become worn over time and need to be replaced. This brake assembly bolt is designed for use with machines made by Black Max, Craftsman, Columbia, Cub Cadet, Huskee, Husky, Mastercut, MTD, Remington, Yard Machines, and Yard-Man. It is a genuine OEM part sourced directly from the manufacturer and is sold individually.

Mower won't start or cuts out during use? A faulty ignition coil prevents spark to the engine. This part restores reliable starting in 30-45 minutes.

Secures engine components and mounts on outdoor power equipment. Replace if bolt is stripped, damaged, or missing to ensure proper assembly and fit.

Replace your leaking or cracked fuel tank causing starting issues or fuel odors. Direct fit for walk-behind mowers and tillers. DIY-friendly repair.

A fuel cap assembly is a component often seen on lawnmowers and other lawn and garden equipment. It is made of durable black plastic and is used to ensure that fuel doesn’t spill out of the fuel tank. Over time, fuel cap assemblies can begin to wear out and cause problems. Sometimes this results in a cap that doesn’t tighten all the way or there may be a fuel smell when using a lawnmower or snowblower. If fuel is leaking, the cap doesn’t fit right, or the cap seems damaged, it’s best to replace it with a new component. This is a simple process that involves removing the original fuel cap assembly and fitting the new assembly to the lawn machine. This fuel cap assembly is a genuine OEM component that comes directly from the manufacturer. It is an individual part that is compatible with MTD, Murray, Cub Cadet, Bolens, Yard-Man, and Yard Machines lawnmowers, snowblowers, chipper shredders, and tillers. No tools are required to replace this component.

Replacement fuel tank for lawn mowers. Mounts to mower exterior to hold fuel supply. Replace if cracked, leaking, damaged, or missing. Direct fit part.

Secures hoses to the carburetor on outdoor power equipment engines. Replace if clamp is rusted, broken, or missing to prevent fuel or air leaks.

Fuel line support bracket for lawn mowers and outdoor power equipment. Secures fuel line in place. Replace if broken, cracked, or missing.

Throttle linkage spring for lawn mowers and tillers. Connects throttle controls to the engine carburetor. Replace if stretched, broken, or missing.

Crankcase cover for lawn mower and tiller engines. Replaces broken, cracked, or missing covers. Protects internal engine components from debris.

Engine won't start after sudden stop? A sheared flywheel key breaks the connection between crankshaft and flywheel. Simple DIY repair.

Seals the dipstick oil fill tube on mowers and small engines. Replace if leaking oil or cracked to prevent engine damage. Confirm fit by model.

Governor gear and shaft assembly for small engines. Mounts inside the crankcase to control engine speed. Replace if gear teeth are worn or stripped.

Replacement oil drain plug for outdoor power equipment engines. Installs in the oil pan to seal the drain opening. Replace if stripped, cracked, or leaking.

Seals the crankcase halves to prevent oil leaks in lawn mowers, tillers, and outdoor power equipment. Replace if oil is leaking or during repairs.

Thumb screw that secures the air cleaner assembly on lawn mower and small engines. Replace if damaged, stripped, or missing due to vibration.

Fix a mower that won't start, runs rough, or stalls frequently with this carburetor assembly. Mixes fuel and air for proper engine ignition.

It's best to have spare O-ring gaskets on hand to rebuild a carburetor when the need arises. Use this manufacturer-approved replacement part to complete the process. When outdoor power equipment shuts off just after starting or won't start altogether, there may be a problem with the carburetor. It could be a leak that causes compression problems keeping the machine's engine from starting. Gasoline may drip from the float bowl because of an O-ring that won't seal or seat evenly all around, or one that has become brittle over time. This is a genuine OEM part compatible with specific lawnmowers, snowblowers, wood chippers, log splitters, tillers, and other garden maintenance machines from Craftsman, MTD, Cub Cadet, MasterCut, Troy-Bilt, and Yard Machines. It is sold individually.

Seals the fuel bowl to prevent leaks and keep dirt out of your fuel system. Replace when cracked or leaking. Confirm fit with your model number.

Fix fuel leaks or loose carburetor connections with this fuel bowl mounting bolt. Secures the fuel bowl to prevent sediment clogs. Quick 5-minute fix.

Creates a leak-proof seal between the fuel drain plug and tank. Replace if you notice fuel leaking from the drain area. Verify fit with your model number.

Replace your lawn mower's carburetor gasket to fix fuel leaks and restore proper engine performance. Verify fit with your model number before ordering.

Heat-blocking spacer that sits between the carburetor and engine block on outdoor power equipment. Replace if cracked, warped, or missing gasket.

Seals and insulates the carburetor from engine heat on lawn mowers and outdoor power equipment. Replace if cracked, worn, or causing air leaks.

This is a carburetor stud for a lawn mower or tiller engine. A carburetor stud enables the carburetor to stay sealed to the intake manifold. They prevent threads from stripping in the metal manifolds and keep the carburetor perfectly aligned. This is an OEM part sourced directly from the manufacturer and is sold individually. When cleaning a carburetor, the user will need to remove the studs. Do not use vice grips when removing a stud, as this will strip the threads. A trick is to put two nuts on the threads and then hold a wrench behind the back nut. Tighten the closest nut, and then use another wrench or impact gun to reverse the stud out. This also works in reverse for replacing it with a new stud to properly place the carburetor so that it seals to the manifold.This part is compatible with several brands, including Bolens, Cub Cadet, Husky, Troy-Bilt, Yard Machines, and Yard Man.

This is a small engine spark plug positioned in the engine cylinder head. It supplies the spark that will ignite the air-fuel mixture to enable an engine to produce power. This particular spark plug is designed with superior corrosion resistance and dependable performance. Small but mighty, this component allows for increased conductivity and heat control. If the spark plug is damaged or in poor condition, many problems may arise in equipment, including sudden stop while running, overheating, and excessive gas consumption. Replace the spark plug by disconnecting the spark plug wire first, then use a socket driver or wrench to remove the spark plug. Install the new spark plug by turning it by hand initially to avoid cross-threading. If it doesn't twist anymore, use a deep socket wrench or socket driver to tighten the plug until snug. The spark plug can also be used to tune up outdoor power equipment or improve a small engine. This part is recommended to be replaced once per season. This part works with lawn mowers, snowblowers, tillers, leaf blowers, log splitters, wood chippers, and others with small engines. It is compatible with brands such as Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and MasterCut. This is a genuine OEM part directly from the manufacturer and is sold individually.

Push rod guide secures and aligns the valve push rod in your engine. Replace if cracked, worn, or missing to restore proper valve train alignment.

Engine running rough or making ticking noises? A worn rocker arm stud can affect valve timing. This replacement stud restores proper valve operation.

Fixes engine misfires and rough running caused by improper valve clearance. This adjusting nut helps restore correct valve timing on lawn mowers and tillers.

This replacement part is a stud. This is a genuine replacement part made by MTD. This part is commonly used inside the engine and works with the cylinder to ensure that the different parts in the machine are running smoothly and effectively.A new stud might be needed if the current one is missing or damaged in any way. This can include being dented, cracked, or bent. It is common that after years of normal wear and tear this part can need replacing. Be sure to wear work gloves while replacing this part as other parts around it can cause injuries.Reference the equipment's manual to ensure a proper repair. This stud is sold individually and is sourced directly from the manufacturer to ensure proper fit. This part is a genuine OEM replacement part made for long-lasting use.

Muffler spark arrestor screen that installs inside the exhaust system. Replace if cracked, clogged with carbon buildup, or missing for safe operation.

This genuine replacement part is a self-tapping screw. A self-tapping screw is a small screw that taps into place with relative ease. Lawnmowers have many screws that secure a variety of different parts. Whether they hold the housing of the various mechanical components or are used as mounting screws for other various parts, self-tapping screws are essential in holding all the different parts of the mower together. Over time, self-tapping screws that are exposed to the elements can rust and deteriorate. If they become too damaged, they might no longer do their job effectively and will need to be replaced. Luckily replacing these screws is a very simple process. To replace the screws, simply unthread the damaged screws and replace them with the new self-tapping screws. If the screws are stripped or too corroded to be removed, consider prying them out with a screwdriver or using a pair of needlenose pliers to rotate them out of their position. This OEM part is sold individually and is compatible with MTD brand mowers.

Fix engine oil leaks or overheating with this cylinder head gasket. Fits various walk-behind mowers, tillers, and lawn equipment. Moderate DIY repair.

This push rod kit is a genuine MTD part, sold individually. This push rod kit can be used as a replacement part in a lawnmower. This kit comes with a variety of push rods in various shapes and sizes, perfect for the replacement or repair of a push rod within the internal machinery of the lawnmower. The push rods could be dented, punctured, scraped, cracked, warped, or eroded, and if this occurs to the point of reduced or no efficacy, the push rod kit should be ordered as a genuine OEM replacement part.This is a genuine OEM replacement directly from the manufacturer. It is sold individually. This push rod kit is compatible with the following outdoor appliance brands: MTD, Bolens, Yard-Man, Yard Machines, Troy-Bilt, Cub Cadet, and Husky.

Replace a worn, broken, or damaged camshaft assembly in your lawn mower or outdoor power equipment engine. Restores proper valve timing and function.

Piston ring set seals the combustion chamber in lawn mower, snow thrower, and tiller engines. Replace when compression drops or oil consumption increases. Verify fit with your model number.

Oil drain plug with washer for lawn mowers and outdoor power equipment. Replaces cracked, stripped, or missing drain plugs to prevent leaks.

Starter rope won't retract after pulling? This recoil pulley and spring assembly fixes rope retraction issues on mowers and small engines. Direct fit.

Fuel line kit for lawn mowers. Connects fuel tank to carburetor. Replace if cracked, dry-rotted, leaking, or hardened to restore proper fuel flow.

A fuel cap assembly is a component often seen on lawnmowers and other lawn and garden equipment. It is made of durable black plastic and is used to ensure that fuel doesn’t spill out of the fuel tank. Over time, fuel cap assemblies can begin to wear out and cause problems. Sometimes this results in a cap that doesn’t tighten all the way or there may be a fuel smell when using a lawnmower or snowblower. If fuel is leaking, the cap doesn’t fit right, or the cap seems damaged, it’s best to replace it with a new component. This is a simple process that involves removing the original fuel cap assembly and fitting the new assembly to the lawn machine. This fuel cap assembly is a genuine OEM component that comes directly from the manufacturer. It is an individual part that is compatible with MTD, Murray, Cub Cadet, Bolens, Yard-Man, and Yard Machines lawnmowers, snowblowers, chipper shredders, and tillers. No tools are required to replace this component.

Oil fill tube assembly for small engines on mowers, tillers, and chippers. Replace if cracked, damaged, or leaking. Installs on engine block.

Replacement muffler stud assembly for lawn mowers, tillers, and small engines. Secures the muffler to the engine block. Replace if broken or missing.

Air cleaner housing panel attaches to the carburetor and holds the air filter in place on small gas engines. Replace if cracked, broken, or missing.

Installing a brand-new air filter keeps the engine in top running condition. When the machine is in operation, the vacuumed air goes through the air filter. Any dirt or dust is left in the filter media. Over time, the filter will become dirty and can no longer provide the same filtering efficiency as before. If left ignored, the tiny particles could clog the engine and the carburetor. You may experience misfires and no engine start-up. An air filter replacement is cheap and easy to do. Simply remove the air cleaner cover and take out the dirty filter. Insert the new filter into the housing. This replacement will take less than 5 minutes. A screwdriver will be needed. The MTD 951-10298 Air Cleaner Kit is a genuine air filter from MTD. Each kit comes with one paper filter and one foam filter. The foam filter can be cleaned with water and detergent. The paper filter, however, needs replacement at least once a year. This air filter kit is compatible with Cub Cadet, PowerMore, and Troy-Bilt. It can also work with other garden equipment like wheel string trimmers, chipper-shredder vacuums, and log splitters.