Parts for Mtd 31AE6FHG705: Engine / Drive Parts

This is a flanged lock nut. It’s designed to apply tension, typically on a joint that needs to have a certain amount of flex. As such, it’s mostly used on snowblower chutes and lawnmower handles. They can remain in place, but with a forgiving connection that can take a beating. The nut size is 3/8, with a thread size of 16. A lock nut will generally last for many years. However, the silicone ring inside will wear down if it’s frequently tightened and loosened. It needs to be replaced when it will no longer reliably remain in place. Generally, this begins as a symptom of slight slippage and worsens as time goes on. Thankfully, whether it’s being used on a snowblower or a lawnmower, this nut is generally straightforward to access. Simply unscrew the old nut, then screw the new nut on until it’s nice and tight. Our flanged lock nuts are genuine OEM MTD nuts, and they are sold individually.

This part is a replacement push cap. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. If the current push cap is broken or has been misplaced, this part can be used as a replacement. It is intended for use with several lawnmower models.The push cap is attached to the wheel hub cap and fits over the end of the axle shaft. This helps to protect the end of the shaft and the attached bolt that holds the wheel into position. When working on or near an engine, always ensure that the equipment is powered off and completely cooled down before attempting to undergo any repairs. For more accurate information on how and where to install this push cap, the appropriate owner's manual and equipment diagrams should be referred to. This push cap is suitable for use on a variety of lawnmower models manufactured by MTD, Yard Machines, Craftsman, Yard Man, and Troy-Bilt. It is a genuine OEM part and thus is made of high-quality, durable materials. This part is sold individually.

This is a simple extension spring with an outside diameter of 0.38 and a slack length of 2.5. It is primarily used as an extension spring for snowblowers, but may be compatible with other lawn equipment. It’s designed to apply tension as the throttle is applied. The more gas there is, the more resistance will be present. Under most circumstances, replacement is easy. When the spring breaks or gets rusty, look at both points of attachment. Memorize where it’s attached, or take a picture, and remove the old spring using a pair of pliers if necessary. Install the new spring and the tool is ready to use. This is an OEM part sourced directly from MTD, and it is sold individually. It’s black in color and was initially designed for Troy-Bilt lawnmowers. However, because this is a versatile part, it has since been repurposed for a number of MTD and related machines in other brands. These include lawn tractors and snowblowers, as well as lawnmowers, in brands such as Ryobi, Yard Machines, Husky, and Cub Cadet.

This part is a replacement screw. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a broken, stripped, or misplaced screw in outdoor power equipment. Screws are critical for holding together parts of the equipment and can be used in many different areas. They are a standard piece of hardware that will need replaced if stripped, corroded, or otherwise defective. It's important when working on or near to any engine to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this screw, the appropriate owner's manual and equipment diagrams should be referred to. As an authentic replacement part, this screw is suitable for use on several outdoor power equipment manufactured by MTD, Craftsman, Troy-Bilt, and other brands. Please This is a genuine part made of high-quality, durable metal and is sold individually.

This genuine OEM replacement auger bearing flange fits a wide range of snowblowers. The auger is the part of a snowblower that scoops up and moves it away from the area being cleared. It is held in place by a bearing, and this flange connects to the bearing to reduce friction and motion. This flange helps prevent grinding, which would degrade the bearing and cause the auger to stop working effectively. Bearings and flanges receive a lot of wear and tear because they are built to absorb friction. Over the natural course of an appliance's life, bearings and flanges will normally wear down and need replacing. If a bearing flange snaps, the auger will no longer turn, and the snowblower will not move snow. To replace a bearing flange, use a socket wrench to gain access to the belt cover and then detach the auger housing. Remove the pulley and thread, then take the auger out of its housing. Pull out the old auger bearing flange and install the new part. This part is compatible with Yard Man, Troy-Bilt, Craftsman, Bolens, MTD, Huskee, and Yard Machines snow blowers. It comes sourced from the original manufacturer and ships individually.

A ball bearing is a rolling element bearing that uses balls to maintain the separation between the bearing races. This part is designed for use with outdoor lawn and garden power equipment such as snowblowers, chippers, shredders, and tillers. It is compatible with products by brands such as Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, and MasterCut.The ball bearing part is crucial because its purpose is to reduce rotational friction while supporting radial and axial loads. Without functioning ball bearings, valuable outdoor equipment would fall apart and quickly stop working. That is why it is important to get any ball bearings replaced if they are worn out or malfunctioning.This ball bearing is made out of metal. The ball bearing is an original OEM part sourced directly from the manufacturer, MTD. It is sold individually.

The drive clutch cable is a clutch or engagement cable that tightens the drive belt or lifts the spinning friction disc contained within the drive housing. It will cause contact between the driveshaft and turn the wheels. If the wheels refuse to turn, it may be due to a cable that is damaged, loose, or snapped. If tightening the tension fails to yield results, this OEM replacement cable is needed. Replacing a drive clutch cable is fairly easy. Remove the original and use pliers and a socket set to install and tighten the new one. "This is a drive clutch cable designed for use in snowblowers produced by MTD, Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, Huskee, Yard-Man, and others. It ships individually and is made of rubber, wire, and metal.

The snowblower auger cable initiates operation of the snowblower’s auger similar to the cable on the handle of a push mower. To start the snowblower, the control handle must be squeezed. This engages the snowblower auger cable to allow the auger to begin turning. When the snowblower auger cable is broken, the snowblower cannot work because the auger will not turn. The length of this snowblower auger cable is 47.48 inches. It is made from high-quality rubber insulation of a metal wire. A pair of pliers and a wrench are needed to complete the repair. If the snowblower still does not work after replacing the snowblower auger cable, check the shear pin as these are prone to breaking and will also prevent the auger from turning. This genuine OEM snowblower auger cable is compatible with snowblowers manufactured by Craftsman, Cub Cadet, Husky, MTD, Troy-Bilt, Yard Machines, and Yard-Man. This part is sold individually. You will need to order any hardware, housing, and the trigger separately if these items also need repair or replacement.

This spacer is a genuine MTD part, sold individually. This spacer can be used as a replacement part in lawnmowers, snowblowers, and wood chippers. This part assists in fastening two components together by creating a slight gap that reduces friction.The spacer might have to be replaced if it is lost, misplaced, or damaged from general wear and tear with long-term use. If the spacer is lost at some point within the typical operation of the appliance and its absence is noticed by the operator, the spacer should be replaced by this genuine OEM replacement part. If the spacer is damaged beyond functionality, the spacer should be immediately replaced. This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This spacer is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Huskee, Yard Machines, Montgomery Wards, Yard-Man, Turf King, and MasterCut.

The roller cable guide is designed for use with lawnmowers. It supports and guides cables to the lasher in the mower.This roller cable guide is a genuine OEM part sourced directly from the manufacturer and is sold individually. This roller cable guide is compatible with the following brands: Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, and Yard-Man.

This replacement clutch drive is a part of the drive system and wheel assembly on snowblowers. The clutch drive engages the transmission when the engine is turned on so that the snowblower auger will rotate as the machine is pushed forward. This part is subject to repetitive motion and constant use so it sometimes just wears down with regular use. If something gets into the snowblower auger or other areas, that could damage the clutch drive, as well. In the event there is damage or the clutch drive no longer works as it should, it will need to be replaced with an OEM part like this one. This is a genuine replacement part made to OEM standards. It can be used in compatible machines from MTD, Craftsman, Troy-Bilt, and Yard-Man. The clutch drive is sold individually. It will not contain any additional parts or components. Disconnect the power supply or disengage the engine before working on outdoor power equipment. Allow the unit to cool and be cautious working around the auger as the blades can be quite sharp.

This tubeless air valve attaches to wheels, allowing air into and out of the tires on various lawn equipment. Regularly replacing this part is considered a part of routine maintenance. Make sure that you use appropriate pliers and other tools for easy installation. Be sure to use gloves when replacing these valves and work with caution so as not to damage the sensitive parts. This OEM tubeless air valve can be the perfect fit for compatible wheels on equipment such as lawn mowers, snowblowers, tillers, edgers, log splitters, and wood chippers. It is designed for use with select models from MTD, including Craftsman, Troy-Bilt, Bolens, Remington, Yardman, RYOBI, Husky, Power Pro, and many others. There is a limited parts warranty on this valve, which is made of durable rubber and metal and designed to offer a high-quality replacement. Sold individually.

A ball bearing is a common type of rolling-element bearing. It will use balls to keep space between the bearing races and eliminate friction and contact between moving parts. Ball bearings used in lawn and garden equipment ensure that axial loads and radial loads are evenly supported and that there is only a limited amount of rotational friction on the component. It distributes weight evenly, but will undergo constant wear and tear from vibration, heat, and friction and will need replacement regularly. This ball bearing is a genuine OEM part suited to use in Craftsman, Cub Cadet, Ryobi, Troy-Bilt, MTD, Huskee, Yard Machines, Bolens, Mastercut, and Yard-Man equipment. It may be needed for repair work done on a lawnmower, snowblower, tiller, edger, or a log splitter.

This hex screw and lock washer are commonly used with lawn mowers and other small engines to secure a motor to the housing of the equipment. It is machined in such a way that it binds the manifold and frame permanently. There are occasions when these bolts have to be removed, typically when major repairs are performed on the engine. In those cases, users often find it advisable to replace the hex bolts and washers with new ones. It happens as well that these screws are so tightly fastened that they cannot be unscrewed and must be cut off. In those cases, it is necessary to replace the original screws. These replacement screws and lock washers are genuine OEM certified replacements that are manufactured to be identical to the hardware they are replacing. In addition to mowers, these hex screws are used to secure engines to devices such as log splitters, edgers, shredders, trimmers, and snowblowers. This screw is compatible with devices made by Husky, Yard-Man, Cub Cadet, Troy-Bilt, Ryobi, Bolens, and Yard Machines.

A flange lock nut, also known as a flange lock or a lock nut, is created to be used in various types of lawn and garden equipment. This flange lock nut holds other parts in place and, when properly threaded, will resist loosening. Over time, a flange lock nut may begin to weaken and may become loose or break. If it appears to be broken or weak, a replacement is required. Flange locks can be adjusted and uninstalled after use. When replacement is required, you may need a socket set, screwdriver, hacksaw, and butane torch. The socket wrench will loosen the bolt it is connected to, while the torch is used to heat the lock nut. A socket wrench may remove the nut, but sometimes cutting it with a hacksaw is required. This flange lock nut is a genuine OEM component directly from the manufacturer and comes in an individual unit. It is made of metal, a gold color, and can be found in various areas of lawn equipment. It works with lawnmowers, trimmers, snowblowers, cultivators, tillers, and leaf blowers by Poulan, MTD, Toro, Cub Cadet, Murray, Troy-Bilt, Bolens, Yard Machines, Craftsman, and Yard-Man.

A flat washer is used with many types of lawn and garden equipment, such as lawnmowers and log splitters. In many cases, the washer is used to hold a bolt in place on a blade. It will often be found between the blade surface and the bolt. The washer is flat with a center hole and ensures the main components of the equipment stay stable and held together when the machine is being used.Over time, the washers on lawn equipment can start to become damaged or break which can result in subpar performance. If a visual inspection shows that the flat washer has warped or is broken, it will need to be replaced. The process is fairly easy and will require nothing more than a screwdriver or socket wrench. The screw or bolt near the washer will need to be removed so the washer can be replaced.This washer is a genuine OEM replacement part that comes as an individual component sourced directly from the manufacturer. It fits lawnmowers, wood chippers, snowblowers, and log splitters by MasterCut, Craftsman, Yard-Man, Toro, Bolens, Cub Cadet, Bolens, Ryobi, Montgomery Wards, Troy-Bilt, Huskee, Murray, MTD, and Yard Machines.

The auger belt is a rubber v-belt that goes around the auger on two-stage snow throwers. The belt is responsible for helping ensure smooth rotation of the auger. Since it is made from rubber, it can wear out over time and snap off or become so damaged that it doesn’t work effectively. Replacement of the belt is a part of routine maintenance that comes with snowblower ownership. The belt can be replaced in no time using a basic wrench set. This auger belt is compatible with several snow throwers, including models from MTD, Cub Cadet, Husky, Troy-Bilt, Yard Machines, and Yard-Man. It works with hundreds of different machines and is made from a durable rubber material.

This belt is used for snowblowers. When the machine is running, the belt turns and propels the auger, which then blows the snow through the chute. If the belt is broken or otherwise not functioning properly, the snowblower will not work.The belt may need to be replaced for any number of reasons. It could become damaged while in use, although this is rare. Over time, the belt could start to stretch and weaken. It may not longer provide the same level of efficiency as when it was new. There is also the chance that the belt could snap. When replacing the belt, it is recommended that the owner also clean the pulleys. This can prevent premature wear and tear.This snowblower belt is for use with many models from MTD, Yard Machines, Cub Cadet, and Troy-Bilt. The belt is a genuine OEM replacement part sourced from the manufacturer. It is sold individually.

This replacement part is an auger pulley, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This auger pulley is generally found in snowblowers and is an important part of the appliance. The auger pulley causes a rotating motion and helps the engine expel the air used to blow snow. A new auger pulley might be needed if the user notices that the auger is no longer rotating properly or is slower than before. It is common for this part to be replaced after a while of normal use as the pulley and auger can both become stripped due to friction overtime. Be sure to wear work gloves while replacing this part.This auger pulley is sold individually. This part is also genuine OEM replacement part sourced directly from the manufacturer. Be sure to refer to the specific owner's manual for more detailed instructions on how to replace this auger pulley.

This part is a replacement friction wheel assembly. It is intended to replace a defective or broken friction wheel assembly in snow blowers.The friction wheel works with the friction disc to turn the drive wheel axle. This part is essential to proper equipment functionality but may be damaged with regular equipment usage. Before beginning this repair job, disconnect spark plug. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before beginning. This friction wheel assembly is a genuine MTD OEM part made of durable materials and is sold individually. It is suitable for use with snow blower models that have been manufactured by MTD, Craftsman, Troy-Bilt, and some other brands.

This part is a hex cap screw that is used on a variety of outdoor power equipment. A hex cap screw is used to fasten components together securely. The head of the screw is shaped like a hexagon, hence the name "hex cap screw."A new hex cap screw may be needed if the current one is stripped, broken, or missing. Since screws are such a small component, it is important to place them in a safe place so that they are not lost. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment.This hex cap screw is a genuine Husqvarna part. It is sold individually. This particular hex cap screw is compatible with chippers, shredders, lawnmowers, lawn tractors, snowblowers, and vacuums that are manufactured by the following brands: Husqvarna, Craftsman, Bolens, Husky, Yard Machines, Yard-Man, MTD, and Troy-Bilt.

A flange nut's unique wide flange design distributes the nut's pressure over the part it is securing. In return, it creates an even fastening surface, which reduces part damage and nut loosening. This one-piece all-metal fastener has a lock nut version that features a protruding circular flange. This drastically increases bearing surface, compatibility either for irregular or oversized holes, and surface tension reduction. Flange lock nuts are the preferred type of fastener for many lawnmower models because it can provide better fastening than regular screws, which are known to loosen under extreme vibration. However, it’s important to know that flange lock nuts are susceptible to wear and tear due to constant vibration exposure. It is essential to replace the broken flange lock nut immediately to prevent serious damage to the lawnmower. The MTD 712-04063 Flange Lock Nut OEM replacement can be used with Craftsman, White Outdoor, Yard Machines, MTD, or Columbia lawnmowers. It is a genuine or OEM MTD replacement part that measures 5/16-18. It is threaded and requires the use of a wrench. This replacement flange lock nut is sold individually. An MTD bolt carriage may also be needed and is sold separately.

This lock washer is used frequently for a number of applications on power yard equipment. The size, 5/16, is the default for many small engine housing and manifold applications. Lock washers are used with machined bolts to fasten engine blocks to the housing of the equipment being used. The compressed washer is able to handle the constant vibration of the small gasoline engine without losing the seal between the screw or bolt and the housing. Typically these lock washers only need to be replaced when they are misplaced during repairs or when the screws that attach them have to be chiseled or cut away, meaning the washers are destroyed as well. These OEM certified replacement washers have been manufactured to the same specifications as the originals they are replacing. In addition to lawn mowers, lock washers of this type and size are frequently used on blowers, lawn tractors, cultivators, snowblowers, and trimmers. Brands compatible with this type of washer are Murray, Husky, Poulan, Bolens, Yard-Man, Cub Cadet, Troy-Bilt, Yard Machines, MTD, and Ryobi.