Parts for Kmart 01877223: Engine Model #5P70mob Parts

This hex screw is a genuine MTD part, sold individually. This hex screw can be used as a replacement part in lawn mowers, snowblowers, tillers, leaf blowers, and wood chippers. The purpose of a screw for one of these outdoor appliances is to serve as a fastening component.This hex screw might have to be ordered as a complete replacement in a hex screw that has been lost, misplaced, or stripped as a result of general wear and tear over long-term use or due to an accidental collision with a hard object. If this occurs, the screw should be removed and replaced by this genuine OEM replacement part.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This hex screw is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, Huskee, Yard Man, and MasterCut.

This is a recoil starter assembly for lawn and garden power equipment. When the recoil starter rope is pulled, this causes the spark which starts the engine.A new recoil starter assembly will be needed if the recoil or pulley system has broken. The rope may become broken or frayed and the plastic on the pulley could crack. If the rope becomes loose and there is no tension when it is pulled, then a new recoil starter assembly will be needed.This part is a genuine MTD part and is an OEM part sourced directly from the manufacturer and it is sold individually. It is used on engines, lawnmowers, lawn tractors, and log splitters that are manufactured by MTD, Yard-Man, Yard Machines, Cub Cadet, Husky, and Troy-Bilt.

This recoil spring and pulley assembly is used in a variety of small gasoline engines that power devices such as mowers, lawn tractors, and log splitters, among other yard and landscaping devices. The assembly works by tightly coiling the spring in the starter housing. When the starter rope is pulled, the tension on the spring is suddenly released, creating a spark that fires the air/fuel mixture. The combustion starts the engine. The constant tightening and releasing of the tension at times will cause wear on the spring, resulting in the need to replace the spring and pulley assembly. To replace the recoil starter assembly, begin by removing the housing. Next, untie or starter rope and check to see if it is frayed and needs to be replaced as well. Remove the old assembly and install the new unit. Remember when re-tensioning the spring to wind the pulley in the opposite direction. Holding the pulley tightly so the spring does not release, attach the cap. Reattach the rope and coil it around the pulley. It is advisable to wear gloves for this task because the pulley and springs have sharp edges. This OEM certified replacement assembly is compatible with Yard-Man, Husky, Cub Cadet, MTD, Yard Machines, and Troy-Bilt yard equipment.

This part is a replacement shroud spacer. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a defective or broken shroud spacer in outdoor power equipment. Spacers ensure that equipment doesn't overheat or vibrate excessively by preventing too much friction from forming between moving components. They are essential to safe and proper functionality and should be replaced when no longer effective. When working on or near an enginee, it is important to ensure the equipment is powered down and completely cool before beginning repairs. For more accurate information on how and where to place this shroud spacer, the appropriate owner's manual and equipment diagrams should be referred to. As an authentic replacement part, this shroud spacer is suitable for use on outdoor power equipment manufactured by MTD, Craftsman, Troy-Bilt, and other brands. Please note that this is a genuine part made of high-quality, durable metal and is sold individually.

This brake assembly bolt is a genuine MTD part that is manufactured to be a replacement part for lawn tractors, push walk-behind mowers, log splitters, trimmers, chippers, shredders, and other engines.On engines such as these, the brake assembly helps work the brake, which stops the engine and any forward motion. It is not abnormal for brake assembly bolts to become worn over time and need to be replaced. This brake assembly bolt is designed for use with machines made by Black Max, Craftsman, Columbia, Cub Cadet, Huskee, Husky, Mastercut, MTD, Remington, Yard Machines, and Yard-Man. It is a genuine OEM part sourced directly from the manufacturer and is sold individually.

This replacement part is a nut. This is a genuine replacement part made by MTD. Nuts are small but typically an important part of many different machines. These parts allow for pieces of the machine to stay secure and in place during use. Nuts usually work with other small parts such as screws and washers to ensure the proper functioning of the machine.A new nut might be needed if the current one is visibly missing or damaged. These parts can become worn down over time due to normal wear and tear. If this is the case it is recommended that it be replaced as soon as possible. This repair should be fairly easy and only require common household tools. Be sure the engine is completely cooled down before attempting to replace this part.This part is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer to ensure a proper fit.

This replacement part is a flywheel. It is a genuine replacement part made by MTD. A flywheel is commonly found in lawnmowers in the engine and was designed to help keep the engine cool during use and allow it to work for many minutes without overheating. A new flywheel might be needed if the engine is overheating more than normal. Be sure to wear working gloves while replacing this part as it can be sharp and cause injury when handled. This part is made of durable metal so that it can operate properly. This flywheel is sold individually and is sourced directly from the manufacturer. This part is a genuine OEM replacement part to ensure long-lasting use and proper fit.

This flange bolt is a genuine MTD part, sold individually. This flange bolt can be used as a replacement part for a variety of small engine outdoor appliances including lawn mowers, snowblowers, string trimmers, leaf blowers, edgers, log splitters, wood chippers, and tillers. The purpose of a flange bolt is to serve as a fastening component, in conjunction with a nut, so components can be secured and affixed to one another over time.The flange bolt might have to be replaced at some point within the standard lifespan of the appliance if it is lost, misplaced, or damaged. The flange bolt can be gradually stripped over time, in which case it should be removed and replaced by this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement.This is an OEM part sourced directly from the manufacturer. It is sold individually. This flange bolt is compatible with the following outdoor appliance brands: MTD, Troy-Bilt, Cub Cadet, Craftsman, Yard-Man, Yard Machines, MasterCut, and Huskee.

This crankcase gasket is a genuine MTD part, sold individually. This crankcase gasket can be used as a replacement part in lawnmowers, tillers, string trimmers, leaf blowers, edgers, log splitters, and wood chippers. The purpose of the crankcase gasket for one of these outdoor appliances is to seal off and protect the area surrounding the crankcase gasket from leakages and the accumulation of external materials within the infrastructure of the crankcase.The crankcase gasket might have to be replaced if the seal is broken due to damage or stripping away of the gasket. This could occur as a result of general wear and tear from long-term use or due to collision with a hard object that warps the gasket beyond functionality. If this occurs, the crankcase gasket should be removed and replaced by this genuine OEM replacement part.This component is a genuine OEM replacement part, sourced directly from the manufacturer. It is sold individually. This crankcase gasket is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Yard Machines, Yard-Man, Huskee, and MasterCut.

This fuel tank bottom bracket is a genuine MTD part, sold individually. This fuel tank bottom bracket can be used as a replacement part for small engine outdoor appliances including lawn mowers, leaf blowers, and wood chippers. The purpose of a fuel tank bottom bracket is to stabilize the placement of the fuel tank.If the fuel tank bottom bracket is compromised to the point that it can no longer bolster the placement of the fuel tank, the fuel tank bottom bracket should be removed and replaced by this genuine OEM replacement part, in accordance with the relevant instructions from an appliance manual.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This fuel tank bottom bracket is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Huskee, Yard Man, and MasterCut.

A fuel cap assembly is a component often seen on lawnmowers and other lawn and garden equipment. It is made of durable black plastic and is used to ensure that fuel doesn’t spill out of the fuel tank. Over time, fuel cap assemblies can begin to wear out and cause problems. Sometimes this results in a cap that doesn’t tighten all the way or there may be a fuel smell when using a lawnmower or snowblower. If fuel is leaking, the cap doesn’t fit right, or the cap seems damaged, it’s best to replace it with a new component. This is a simple process that involves removing the original fuel cap assembly and fitting the new assembly to the lawn machine. This fuel cap assembly is a genuine OEM component that comes directly from the manufacturer. It is an individual part that is compatible with MTD, Murray, Cub Cadet, Bolens, Yard-Man, and Yard Machines lawnmowers, snowblowers, chipper shredders, and tillers. No tools are required to replace this component.

Fuel filters are created to strain out gas before it reaches the carburetor in lawnmowers and other gardening tools. Located in the fuel line or the fuel tank, it prevents unwanted debris from reaching the carburetor, which can cause engine damage. If the fuel filter is damaged or becomes clogged with material, it no longer offers the same protection to the carburetor. This can lead to difficulty starting the lawnmower and decreased performance. Correcting this issue early can prevent damage that might require a new lawnmower. Maintenance of the lawnmower by adding fuel stabilizer, changing the oil, and replacing the air filter will increase the life of lawn care equioment. Even if no issues are present, the fuel filter should be replaced after about 200 hours of use. Disconnecting the spark plug should be done prior to installing a new fuel filter. This fuel filter is a genuine OEM component directly from the manufacturer and comes as an individual part. It can be used with various Craftsman, Cub Cadet, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and Mastercut lawnmowers, tillers, blowers, and wood chippers.

This crankcase cover gasket is a genuine MTD part. It is made for use on several models of log splitters, chippers-shredders, leaf blowers, lawn mowers, wood chippers, and similar machines. This part seals the halves of the crankcase. It is not abnormal for the crankcase cover gasket to become worn over time, but it can also be important to replace it whenever it is disassembled for another engine repair. This ensures that the seal is fresh and complete. This crankcase cover gasket is a genuine OEM part sourced directly from the manufacturer. It is sold individually. It is compatible with machines manufactured by Craftsman, Cub Cadet, Huskee, Husky, Mastercut, MTD, MTD Gold, Troy-Bilt, and Yard-Man.

The flywheel key keeps the engine flywheel and the crankshaft connected. In the event that the engine is forced to a sudden stop, the flywheel key could be sheared off, making it impossible for the engine to start back up again. Replacing the flywheel key is a part of routine maintenance for many modern engines, so it should be inspected and replaced as needed. This sturdy metal flywheel key is easy to install, but remember to choose the right torque setting when doing the replacement. Always disengage the spark plug and wear gloves when replacing engine parts. This genuine flywheel key is designed to be used in a number of lawn and garden equipment products from MTD, Troy-Bilt, Yard Machines, Cub Cadet, Yard-Man, Husky, and Bolens. It can be used as a replacement for many models of snowblowers, lawnmowers, and log splitters. Sold individually.

This dipstick oil fill o-tube ring is a genuine MTD part. It is manufactured as a replacement part for various push walk-behind mowers, self-propelled walk-behind mowers, tillers, snowblowers, leaf blowers, log splitters, wood chippers, and other small engines.This part is used to check the level of oil in these machines. Dipstick o-rings especially may become too dirty or damaged to be useful anymore. They may also become lost or damaged. Being able to check the oil is an important maintenance step, so this part must be replaced if necessary. This is a genuine OEM part sourced directly from the manufacturer and sold individually. It is compatible with machines made by many brands, including Huskee, Husky, Yard Machines, MTD, Remington, Yard-Man, Cub Cadet, Craftsman, and MasterCut.

This oil fill tube assembly is a genuine MTD part, sold individually. This oil fill tube assembly can be used as a replacement part in lawn mowers, tillers, leaf blowers, and wood chippers. The purpose of the oil fill tube assembly in a small engine outdoor appliance is to allow the operator of the appliance to channel oil into the appliance so that the oil can be used to ignite the spark plugs and power on the engine for standard use of the appliance.This oil fill tube assembly might have to be ordered as a complete replacement part in an oil filler tube assembly that has been sufficiently damaged as to permanently affect its typical functionality for the appliance. If the oil fill tube assembly has been punctured, dented, torn, ripped, scraped, cracked, or eroded to the point of no efficacy, the oil fill tube assembly should be removed and replaced by this genuine OEM replacement part.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This oil fill tube assembly is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Yard Machines, Huskee, Yard Man, and MasterCut.

This replacement part is a crankshaft seal. This is a genuine replacement part made by MTD. This part is able to act as a seal between the part and the space around it. This ensures that the engine is able to operate properly.A new crankshaft seal might be needed if air or fuel is escaping from around this part. If the current part is damaged such as being stripped or cracked, it is recommended that it be replaced. Be sure that the engine is completely down. Refer to the appropriate user guide for more information on how to replace this specific crankshaft seal.This crankshaft seal is sold individually and is sourced directly from the manufacturer to ensure proper fit. This part is a genuine OEM replacement part for long-lasting use.

This is a genuine replacement for the air cleaner thumb screw found on select engines used in lawn mowers. The thumb screw is a specialty part that is used to secure the air cleaner in a stable position. Over time, the screw can become damaged or worn because of the constant engine vibrations or exposure to high heat. This screw may also be lost during air filter replacements or other repair work. In either case, it should be replaced with a genuine part like this one to ensure the air cleaner remains secure and the machine can continue to be used. This genuine OEM thumb screw is manufactured by MTD and is compatible with several machines from the brand. It can also be used with models from Bolens, Yard Man, Yard Machines, HUSKEE, Cub Cadet, and Troy-Bilt. There are hundreds of compatible models that can use this thumb screw. The part is made of durable metal with a black plastic grip for easy installation with no tools required. This item is sold individually and does not include additional hardware or parts. Always allow the engine to cool completely and wear gloves when working on lawn and garden equipment.

This air cleaner housing is a genuine MTD part, sold individually. This air cleaner housing can be used as a replacement part for lawn mowers and leaf blowers. The air cleaner housing provides a casing for the air cleaner so that it can shield the internal engine from dirt, debris, and pebbles. Check the air cleaner housing regularly to ensure that it is intact and no debris is getting into the engine. Remember to wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This air cleaner housing is compatible with the following brands: MTD, Huskee, and Yard-Man.

Installing a brand-new air filter keeps the engine in top running condition. When the machine is in operation, the vacuumed air goes through the air filter. Any dirt or dust is left in the filter media. Over time, the filter will become dirty and can no longer provide the same filtering efficiency as before. If left ignored, the tiny particles could clog the engine and the carburetor. You may experience misfires and no engine start-up. An air filter replacement is cheap and easy to do. Simply remove the air cleaner cover and take out the dirty filter. Insert the new filter into the housing. This replacement will take less than 5 minutes. A screwdriver will be needed. The MTD 951-10298 Air Cleaner Kit is a genuine air filter from MTD. Each kit comes with one paper filter and one foam filter. The foam filter can be cleaned with water and detergent. The paper filter, however, needs replacement at least once a year. This air filter kit is compatible with Cub Cadet, PowerMore, and Troy-Bilt. It can also work with other garden equipment like wheel string trimmers, chipper-shredder vacuums, and log splitters.

The carburetor gasket plate creates a seal between the air cleaner base and the carburetor body. This plate is made of durable material but it is exposed to constant pressure and heat, which can cause it to degrade over time. It can also become damaged or broken, which would require a replacement. If the gasket is degraded or damaged, it could allow air to leak out of the engine, reducing compression and affecting performance. Severe cases could result in total engine failure, which is why replacement should be done as soon as possible. This genuine OEM gasket plate is designed to be used in a variety of log splitters, tillers, and lawn mowers from brands like Yard Machines, MTD, Yard Man, Cub Cadet, Troy-Bilt, and Husky. This carburetor gasket plate is made of durable materials and sold as an individual piece. No hardware is included for this part and will require an additional purchase if needed. Always allow the engine to cool before performing repairs and wear gloves for hand protection.

It's best to have spare O-ring gaskets on hand to rebuild a carburetor when the need arises. Use this manufacturer-approved replacement part to complete the process. When outdoor power equipment shuts off just after starting or won't start altogether, there may be a problem with the carburetor. It could be a leak that causes compression problems keeping the machine's engine from starting. Gasoline may drip from the float bowl because of an O-ring that won't seal or seat evenly all around, or one that has become brittle over time. This is a genuine OEM part compatible with specific lawnmowers, snowblowers, wood chippers, log splitters, tillers, and other garden maintenance machines from Craftsman, MTD, Cub Cadet, MasterCut, Troy-Bilt, and Yard Machines. It is sold individually.

The fuel bowl gasket provide an airtight seal to the fuel bowl. This will ensure that air, along with dirt and debris, do not make their way into the fuel. Gaskets will wear out over time. They will start to crack and fall apart, and they will no longer be capable of providing you with the necessary seal for the fuel bowl. The repair is easy and should only take between half an hour and an hour. This is an OEM replacement fuel bowl gasket part that is made from high-quality, durable rubber. Each of the fuel bowl gaskets is sold individually. The gasket can work well with many different types of outdoor power equipment, including snowblowers, chipper-shredders, tillers, lawn tractors, mowers, and other small engines. The fuel bowl gasket is compatible with many brands, including MTD, Yard Machines, Yard-Man, Troy-Bilt, Huskee, Cub Cadet, and Mastercut.

This is a genuine OEM replacement fuel bowl bolt for a snowblower, tiller, or chipper engine. The fuel bowl is a part of the fuel filtration system designed to prevent sediment from clogging up the carburetor. Fuel moves from the fuel tank and passes through the fuel bowl to catch any debris. It is essentially a particle filter. This bolt mounts the fuel bowl in place. The two most likely reasons why a fuel bowl bolt might need replacing are general wear and tear or loss. This bolt is located fairly close to the outside of the engine, making it more susceptible to the elements. Over time, the bolt may corrode and will need replacing. If lost while making a repair to the fuel bowl itself, the fuel bowl bolt will need to be replaced. Use a wrench to make the repair. This fuel bowl bolt is a top of the line replacement part for Bolens, Yard Machines, MTD, Troy-Bilt, Huskee, and Yard Man appliances. This part does not include any additional hardware, as it ships individually.

The fuel drain plug gasket creates a solid, leak-proof seal in the fuel drain. The gasket goes into the connection between the drain and the fuel tank. In the event that this gasket fails, there could be fuel leakage from the equipment that could be costly or even dangerous. Make sure to inspect and replace all gaskets regularly to ensure that the engine is working efficiently. This gasket is made of durable rubber material and is simple to install. drain the fuel to provide access to the drain plug and the fuel line without spilling fuel everywhere. Always wear gloves and make sure to disconnect the spark plug or disable the engine before working on any outdoor power equipment. This OEM replacement fuel drain plug is compatible with several tillers, snowblowers, lawnmowers, tractors, and other outdoor power equipment made by Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, MTD, Huskee, Yard-Man, and MasterCut. Sold individually.

This carburetor insulator is a genuine MTD part sold individually. This carburetor insulator can be used as a replacement part in lawnmowers, leaf blowers, and wood chippers. The purpose of the carburetor insulator for one of these small engine outdoor appliances is to ensure that the air and fuel taken in by the carburetor is properly cooled and does overheat.If the carburetor insulator is no longer keeping heat away from the area of the carburetor when intaking fuel and air, the carburetor insulator should be removed and replaced by this genuine OEM replacement part.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This carburetor insulator is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Huskee, Yard-Man, and MasterCut.

This part is a replacement carburetor insulator gasket. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a defective or worn carburetor insulator gasket in outdoor power equipment. Gaskets are essential, as they ensure that the space where components join together is sufficiently sealed, which helps to prevent leaks. Gaskets are subject to wear and tear over time, causing them to become brittle, worn, and ineffective. Thus, this part will need to be replaced. When working on or near an engine, it's important to ensure that the equipment is powered off and completely cool before beginning any repairs. For more accurate information on how and where to place this carburetor insulator gasket, the appropriate owner's manual and equipment diagrams should be referred to. As an authentic replacement part, this carburetor insulator gasket is suitable for use on outdoor power equipment manufactured by MTD, Craftsman, Troy-Bilt, and other brands. Please note that this is a genuine part made of high-quality, durable materials and is sold individually.

This is a small engine spark plug positioned in the engine cylinder head. It supplies the spark that will ignite the air-fuel mixture to enable an engine to produce power. This particular spark plug is designed with superior corrosion resistance and dependable performance. Small but mighty, this component allows for increased conductivity and heat control. If the spark plug is damaged or in poor condition, many problems may arise in equipment, including sudden stop while running, overheating, and excessive gas consumption. Replace the spark plug by disconnecting the spark plug wire first, then use a socket driver or wrench to remove the spark plug. Install the new spark plug by turning it by hand initially to avoid cross-threading. If it doesn't twist anymore, use a deep socket wrench or socket driver to tighten the plug until snug. The spark plug can also be used to tune up outdoor power equipment or improve a small engine. This part is recommended to be replaced once per season. This part works with lawn mowers, snowblowers, tillers, leaf blowers, log splitters, wood chippers, and others with small engines. It is compatible with brands such as Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and MasterCut. This is a genuine OEM part directly from the manufacturer and is sold individually.

This part is a replacement push rod guide. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part is intended for use as a replacement for a broken or defective push rod guide on various lawnmower models. The push rods themselves are what transfer oil to the equipment's cylinder head. They also help to locate the rocker arms, and the push rod guide plate is necessary for securing and locating the pushrods. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to install this push rod guide, the appropriate owner's manual and equipment diagrams should be referenced. This push rod guide is a genuine OEM part made of durable materials and is sold individually. It is suitable for use with lawnmowers that have been manufactured by MTD, Yard Man, Cub Cadet, Husky, and Troy-Bilt.

This part is a replacement rocker arm stud. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part is intended for use as a replacement for a broken or defective rocker arm stud on various types of outdoor small engine power equipment. This rocker arm stud works by securing the cylinder head. The rocker itself slides over the stud and is then held securely by the nut that locks it into place. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to install this rocker arm stud, the appropriate owner's manual and equipment diagrams should be referenced. This rocker arm stud is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with lawnmowers, blowers, and tillers that have been manufactured by MTD, Yard Machines, Cub Cadet, Bolens, Husky, and Troy-Bilt.

This is a valve adjusting nut that is an integral part of many different types of lawn and garden equipment, such as lawnmowers, trimmers, and snowblowers. The location of the part will vary based on the model. Users can refer to the equipment's diagram to determine where the component is located. The nut acts as a fastener and is made of durable metal. However, it can be damaged, may break, or become lost and will need to be replaced.If the valve adjusting nut is damaged or missing, it will need to be replaced. A pair of work gloves and basic tools will be needed for the process. Take the lawn and garden equipment and place it on a level surface before removing the spark plug wire. Access the location of the nut and remove it before installing the new replacement part.This is a genuine OEM replacement part that is directly sourced from the manufacturer. The valve adjusting nut is sold as an individual item. The part is made to be compatible with snowblowers, lawnmowers, string trimmers, leaf blowers, edgers, log splitters, wood chippers, and tillers manufactured by MTD, Troy-Bilt, Yard Machines, Craftsman, Cub Cadet, Huskee, MasterCut, and Yard-Man.

This replacement part is a stud. This is a genuine replacement part made by MTD. This part is commonly used inside the engine and works with the cylinder to ensure that the different parts in the machine are running smoothly and effectively.A new stud might be needed if the current one is missing or damaged in any way. This can include being dented, cracked, or bent. It is common that after years of normal wear and tear this part can need replacing. Be sure to wear work gloves while replacing this part as other parts around it can cause injuries.Reference the equipment's manual to ensure a proper repair. This stud is sold individually and is sourced directly from the manufacturer to ensure proper fit. This part is a genuine OEM replacement part made for long-lasting use.

This is a muffler assembly that is used with many types of lawn and garden equipment from major manufacturers. The part is connected to the exhaust tube and is tasked with reducing the noise made by the exhaust. As time goes on, the muffler assembly can start to become damaged or malfunction and may need to be replaced. When replacing the muffler assembly, make sure the spark plug is removed and the equipment is powered off. It should be placed on a stable surface during the replacement process. Take the bolts out of the muffler and remove them from the engine. Take the bolts from earlier and install them into the replacement muffler. Install the gaskets, heat shield, and other parts before placing the new muffler into the lawn equipment. Reassemble all parts before using the tool.The muffler assembly is an authentic OEM replacement part that is directly sourced from the manufacturer. It is made to be used with lawnmowers, tillers, leaf blowers, log splitters, and wood chippers manufactured by MasterCut, Craftsman, Yard-Man, Cub Cadet, Huskee, MTD, and Yard Machines. This component is sold as an individual item.

This spark arrestor is a genuine MTD part. It is a replacement part for lawn mowers, log splitters, and walk-behind mowers. The spark arrestor is an important safety feature, and it is illegal to sell or operate a machine without one.This part arrests or extinguishes sparks that are created by the engine and other components while the mower is in use. It prevents fires, and mowers should never be used without one.This spark arrestor is a genuine OEM part sourced directly from the manufacturer. It is sold individually. It is compatible with machines made by Craftsman, MasterCut, Bolens, Cub Cadet, Husky, MTD, Troy-Bilt, and Yard-Man.

This genuine replacement part is a self-tapping screw. A self-tapping screw is a small screw that taps into place with relative ease. Lawnmowers have many screws that secure a variety of different parts. Whether they hold the housing of the various mechanical components or are used as mounting screws for other various parts, self-tapping screws are essential in holding all the different parts of the mower together. Over time, self-tapping screws that are exposed to the elements can rust and deteriorate. If they become too damaged, they might no longer do their job effectively and will need to be replaced. Luckily replacing these screws is a very simple process. To replace the screws, simply unthread the damaged screws and replace them with the new self-tapping screws. If the screws are stripped or too corroded to be removed, consider prying them out with a screwdriver or using a pair of needlenose pliers to rotate them out of their position. This OEM part is sold individually and is compatible with MTD brand mowers.

This replacement part is a piston pin. This is a genuine replacement part made by MTD. This part is small but important to ensure that the piston is working properly during use. A new piston pin might be needed if the current one is missing or damaged. It is not uncommon for the pin to be stripped down over time due to normal wear and tear. The pin may also become lodged in place and should be replaced if this happens. Wear work gloves when completing this repair to prevent injury during the job. The engine should be completely turned off and cooled down before beginning repairs.This part is sold individually and is sourced directly from the manufacturer. This is a genuine OEM replacement part.