Parts for Lg LCG3611ST / 00: Exploded View Parts

This governor controls and regulates the washer's motor speed so the drum spins at the correct RPM for wash and spin cycles. Replacing a failing governor restores consistent spin behavior and helps prevent uneven agitation. What it does

• Regulates motor/drive speed so wash and spin cycles run at intended speeds
• Helps maintain consistent agitation and balanced spinning
• Can cause slow spins, no spin, or erratic drum speed when worn or faulty
• Works with the washer's motor and transmission to match cycle demands

• One governor assembly

• Disconnect power and water supply before starting any repair
• Access typically requires opening the cabinet or control panel; keep track of fasteners
• Inspect related parts (drive belt, motor coupling, wiring) for wear while replacing

This accessory assembly replaces a worn or missing component to restore proper fit and secure connections on your appliance. It helps stop loose parts and ensures the related area functions as intended. What it does:

• Replaces the original accessory assembly that secures or supports nearby components
• Stops movement, rubbing, or rattling caused by a damaged or missing assembly
• Restores correct alignment for the affected area to reduce noise and wear
• Works with the appliance's existing fasteners and mounting points

• Disconnect power (and water if applicable) before starting work
• Follow the OEM instructions for removal and installation
• Use basic hand tools; avoid over-tightening fasteners to prevent damage

This gas valve assembly controls gas flow to the appliance's burner, restoring reliable ignition and heating when the original valve fails. It replaces a faulty or leaking valve to help the unit heat safely and consistently. What it does:

• Regulates and routes gas to the burner based on the appliance's control signals
• Prevents gas flow when the appliance is off or during safety shutoff conditions
• Commonly used to address symptoms like no heat, weak heating, or a persistent gas smell when confirmed at the valve
• Works as the appliance's primary gas control component in the fuel delivery system

• One gas valve assembly

• Turn off gas supply and disconnect power before servicing; verify both are isolated
• Inspect all gas fittings and use an approved leak detection method after installation
• Do not modify the part; use proper tools and follow manufacturer service instructions

This replacement screw is a factory-style fastener used to secure components in place and restore proper fit and function. It's a direct-fit hardware piece sized and finished to match the original installation. What it does:

• Secures panels, brackets, or assemblies to prevent rattling or misalignment
• Restores original mounting strength where a stripped or missing screw causes loose parts
• Helps maintain proper panel gaps and component positioning for reliable operation
• Appropriate where the appliance requires the OEM-style screw head and thread form

• Screw

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or damage plastic parts
• Replace any damaged or corroded mating hardware for best results
• Disconnect power to the appliance and follow manufacturer safety instructions before servicing

This rigid replacement pipe routes fluid between components to restore proper flow and prevent leaks. It's a direct-fit service part when a damaged or corroded pipe is causing poor performance or visible leakage. What it does:

• Channels liquid between system components to maintain correct fluid routing
• Restores secure connection where damaged, cracked, or corroded piping causes leaks
• Helps stop drips and pooling that can lead to component damage or error conditions
• Re-establishes proper flow when an internal or external pipe is obstructed or compromised

• One replacement rigid pipe

• Turn off and unplug the appliance and shut off the water supply before starting
• Inspect mating fittings and replace damaged gaskets or clamps to ensure a leak-free seal
• Use appropriate tools and avoid over-tightening fittings to prevent cracking the pipe
• After installation, restore power/water and check carefully for leaks during a complete test cycle

This nozzle assembly directs water/ice from the dispenser to the glass, restoring a clean, controlled flow for reliable dispensing. Designed to replace a damaged, cracked, or leaking dispenser nozzle. What it does:

• Channels water or ice from the dispenser chute for proper dispensing
• Prevents leaks and messy drips caused by cracked or worn nozzles
• Helps ensure a straight, sanitary flow into cups and containers
• Restores proper alignment when the original nozzle is loose or misaligned

• Turn off water supply and unplug the appliance before attempting service
• Replace only with the exact part number to ensure fit and function
• Handle plastic components carefully to avoid cracking during installation

Restore precise heat control on your range or cooktop. This knob assembly replaces a worn or broken control knob so you can smoothly turn the burner or element on, off, and adjust heat to the setting you need. What it does:

• Attaches to the burner valve or element switch to control on/off and heat level
• Restores proper engagement and alignment when the original knob is cracked or stripped
• Helps ensure accurate position indication for consistent settings
• Common symptoms: knob loose, cracked, missing, or spins without engaging; burner/element doesn't respond or is hard to adjust

• 1 knob assembly

• Disconnect power and, for gas units, shut off the gas supply before servicing
• Pull the old knob straight off the control stem; avoid prying against the panel
• Align the new knob with the stem and press firmly until fully seated
• Verify smooth operation and correct pointer alignment through all settings

This burner is the cooktop surface flame assembly that produces heat for cooking. It replaces a damaged or worn surface burner to restore proper flame and even heating on the cooktop. What it does

• Provides the primary flame source for a gas cooktop burner
• Restores consistent flame distribution when the original burner is warped, cracked, or clogged
• Can resolve symptoms such as weak or uneven flame, burner that won't sustain a flame, or visible damage to the burner head
• Works with the igniter/safety valve assembly to light and maintain the burner

• One surface burner

• Turn off gas supply and power to the appliance before servicing
• Use basic hand tools; handle the burner carefully to avoid bending or damaging the ports
• Clean burner ports of debris before installation to ensure proper flame pattern

The Burner Cap is an OEM component specifically designed for LG gas ranges. This cap sits atop each burner element and functions to safely contain the burner flame during cooking. 

The burner cap regulates burner temperature and optimizes heat conduction. It distributes the flame evenly across the bottom of the cookware for rapid, consistent cooking results. 

Symptoms of a bad burner cap include: 

• Warping, cracks, or holes that allow flame to escape 
• Discoloration or material fatigue affecting flame quality
• Loose fit that impacts flame control or introduces safety issues

Causes may include normal wear over time exposed to heat, burns, or bending from heavy pots/pans.

Replacing this OEM LG burner cap will restore your range's heating performance, avoid potential safety hazards, and maintain proper cooking temperatures.

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

This burner tube directs gas from the valve to the oven's burner assembly for proper flame distribution and heat during baking and broiling. Replacing a damaged tube restores safe, even combustion and consistent cooking performance. What it does

• Channels gas to the oven burner so the flame lights and stays steady
• Helps maintain even heat for reliable cooking and browning
• Prevents gas leaks caused by cracks, holes or severe corrosion
• Can resolve symptoms like weak or uneven flames, flame blowouts, or visible tube damage

• Turn off gas supply and electrical power before beginning any service.
• Inspect mounting hardware, gaskets and alignment; replace any worn seals to ensure a proper fit.
• Do not force, bend, or dent the tube during installation; handle carefully to avoid leaks.

This glass turntable plate replaces a cracked or missing microwave cooking surface to restore stable, even rotation and safe food support. Designed to fit the oven's turntable system and help prevent uneven heating and spills. What it does:

• Provides a flat, heat-resistant surface for cookware and food while the microwave runs
• Sits on the roller ring/drive coupler so food rotates for even cooking and reheating
• Replaces chipped, cracked or missing plates that can cause wobbling, noise or uneven heating
• Helps prevent direct contact between food and the microwave cavity floor

• One glass plate assembly

• Unplug the appliance or disconnect power before servicing
• Handle glass carefully; replace if chipped or cracked to avoid breakage during use
• Set the plate onto the roller ring/drive support so it seats securely before operating
• No special tools typically required;

The Burner Cap is an OEM part for LG ranges. It covers the burner assembly on the cooktop and directs flame for efficient cooking. Burner caps allow heat to be spread evenly across pans while containing dangerous flames and sparks.

Causes of a bad burner cap generally include cracks, warping, or damage from high heat over time. Accidental mishandling or impact can also weaken burner caps.

Symptoms of a bad burner cap include:

• Inefficient or uneven heating of cookware
• Visible flames escaping outside the burner area
• Cracks or holes in the burner cap surface
• Looseness, wobbling, or inability to properly secure the cap

This OEM LG part is also compatible with some Kenmore models.