Jered F Somerville , MA October 20, 2020 Appliance: Model DCS-RG-364GL Grill burner on DCS range would not light The grill igniter was broken and needed replacing. The igniter itself is easily accessed but the connectors for it, not nearly as much! The repair is simple, but requires patience and small fingers. 1) Turn off power to the appliance. 2) Remove the grill grates, heat diffuser panel and flame tube; these components all press or rest in position. 3) The igniter is in the lower left corner, secured by two Phillips head screws with mating nuts underneath. These may be locked in place with hardened grease and require some gentle torqueing to free. Make sure to catch the nuts from the bottom so they don't get lost into the grill. 4) The wires feed through a heat-protection sleeve to an area accessed through an opening on the front inside of the grill assembly. The grill assembly cannot be easily disassembled further. With small fingers, follow one wire to a spade connector between pieces of sheet metal and gently free. The other wire is connected via a ceramic wire nut to a loose wire; remove this wire nut and remove the igniter and sleeve. 5) On the new igniter, use a wire stripper to remove the "male" spade connector and expose 1cm of bare wire. Feed the wires through the heat-protection sleeve, and then through the channel at the front of the grill enclosure. 6) With triple-jointed fingers while hanging from the ceiling, connect the female spade connector on the new igniter to the terminal on the thermal valve control; you can feel this but not see it, and there is very little space to access. This will take between 5 minutes and 5 hours, depending on your dexterity. 7) Use the ceramic wire nut to connect the other igniter wire to the loose wire from front of stove. 8) Secure the igniter with the two screws/nuts removed in step 3; replace all removed grill components. Turn on power to the appliance. Read More... Do-It-Yourself Rating: Repair Time Estimate: 1-2 hours Tools: Screwdrivers
Robert K Cranford , NJ June 15, 2021 Appliance: Model DCS RDS-305 Oven was taking too long to heat up. The igniter in the oven needed to be replaced. My wife is happy once again. Read More... 1 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Screwdrivers
Phil L Oak Park , IL March 26, 2021 Appliance: Model RGV-366-N Oven was not lighting. Replaced igniter. Read More... Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Nut Drivers, Screwdrivers, Socket Set
Steven W Arcadia , CA September 01, 2020 Appliance: Model RTG-36 Oven taking a long time to heat up. My problem was the oven was taking a long time to heat up to proper temperatures and upon reading online, It could be 3 issues, which is the igniter, thermostat and/or circuit board. .Upon opening up the oven and checking the oven the burner seems to not open up to the fullest. So, I figured the Ignitor was not heating up enough to open the burner. After I changed the Ignitor, the oven worker perfectly and took less than 15 minutes to repair. Read More... Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Screwdrivers
Michael S Zachary , LA June 27, 2020 Appliance: Model RGU-366-N Faulty oven igniter. Simple plug in replacement part. Two screws securing the part and 6 machine screws to remove back panel. Most difficult part of the job is moving the stove to work behind it and the crouched position to access work area. The part was an exact match. Well packaged and arrived timely. Diagnosis took awhile as there are not a lot of videos explaining that although the ignitor may still glow red hot it may not draw even amperage to sufficiently function properly. Very positive experience as I’m sure this saved me $150-200. Read More... Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Nut Drivers, Pliers, Screwdrivers