Parts for Ge ZISB36DTE: 01 - Freezer Door Parts

This part has been discontinued by the manufacturer and is no longer available.

Spring for recess duct. For spring sleeve use WR2X4822.

This part has been discontinued by the manufacturer and is no longer available.

Lanyard for dispenser door.

Dispenser selector lever for refrigerators. Installs on selector switch assembly. Replace if cracked, broken, or missing to restore proper operation.

Molded housing that supports and aligns refrigerator dispenser components. Replace if cracked, broken, or no longer holding chute and actuator securely.

Color: clear. It's 7 watts 130 volts.

Ice maker dispenser door.

Time delay display arm.

Includes 12 washers.

Ice chute door lever for refrigerator dispensers. Replaces broken, cracked, or missing levers that control ice door opening and closing.

This is the right side duct gasket. For left side use WR14X247.

This is the left side duct gasket. For right side use WR14X246.

Support bracket that holds the cradle switch in your refrigerator. Replace if the original is cracked, broken, or missing to properly secure the switch.

Includes 12 screws.

Mounting screw for refrigerators and freezers. Secures internal components and panels. Replace if stripped, missing, or damaged during maintenance.

This pack contains twelve replacement screws used to fasten appliance panels, trim, and components. They restore secure mounting and help stop rattling, loose panels, and gaps for a safer, quieter appliance. What it does:

• Secures exterior and interior panels, brackets, and trim pieces
• Restores proper fit where missing or stripped screws cause movement or noise
• Helps maintain appliance alignment and prevents parts from vibrating loose
• Used for general-purpose repairs on compatible GE appliances

• Disconnect power or unplug the appliance before performing any internal repairs
• Use the correct screwdriver bit and avoid overtightening to prevent stripping threads
• Keep remaining screws in a labeled container for future service
• If a screw does not seat easily, stop and verify correct fit to avoid damage

Replacement mounting screw that secures panels and internal components in your freezer. Replace stripped, rusted, or missing fasteners to restore stability.

Replacement .060 shim for refrigerator door alignment. Installs between door and cabinet to ensure proper spacing and seal. Needed when worn or missing.

Thin leveling spacer that corrects height and alignment gaps in refrigerator components. Replace when worn, missing, or needed for proper fit.

Includes 12 screws.

Size: 1/4 inch diameter.

Magnetic door gasket seals the refrigerator compartment to maintain temperature and reduce energy loss. Replace when worn, cracked, or loose. Confirm fit by model.

For fresh food door top handle endcap or freezer door bottom handle endcap.

Freezer door handle.

Freezer door top trim.

Freezer door side trim.

Freezer door bottom trim.

Replace your refrigerator's door hinge to restore proper door alignment and operation. Needed when the existing hinge is cracked, broken, or worn out.

Freezer side bottom door hinge.

Freezer side top hinge shim. For bottom hinge shim use WR2X8593.

Freezer side bottom hinge shim. For top hinge shim use WR2X8592.

For fresh food door top handle endcap or freezer door bottom handle endcap.

Connects water supply tubing sections in your refrigerator. Replace this plastic compression union if it's cracked, leaking, or broken. Installs inline.

This fiberglass sleeve protects and insulates tubing and wiring, helping prevent chafing and damage where lines pass through openings or near sharp edges. It's a simple, durable way to extend component life and reduce noise from rubbing. What it does:

• Provides abrasion protection for water lines, hoses, and electrical wiring
• Adds thermal insulation to help reduce condensation and exposure to temperature extremes
• Cushions components where they pass through metal or plastic panels to prevent wear
• Helps reduce rubbing noises caused by vibration or movement

• Disconnect power and water supply before starting
• Inspect surrounding areas for sharp edges or corrosion; replace sleeve if frayed or damaged
• Slide sleeve over the hose or wire; trim to length with scissors if needed and ensure full coverage of exposed areas
• Use appropriate clamps or zip-ties as required to secure the sleeve without compressing it