Parts for Ge ZISS48NCBSS: 01 - Freezer Door Parts

This .030-inch shim is a thin leveling spacer used to correct small height and alignment gaps. It helps stabilize and align appliance components for proper fit and reduced vibration during operation. What it does:

• Provides a precise 0.030-inch thickness to raise or level panels, doors, or chassis components
• Helps eliminate small gaps that can cause rubbing, misalignment, or uneven sealing
• Reduces vibration or rocking by evening out contact points and load distribution
• Useful during cabinet installation or when replacing worn leveling feet or brackets

• Disconnect power (and water if applicable) to the appliance before performing service
• Use appropriate hand tools and keep shims flat and properly seated under the component being adjusted
• Add shims incrementally—do not force parts into position or over-tighten fasteners after shimming

This pack contains twelve replacement screws used to fasten appliance panels, trim, and components. They restore secure mounting and help stop rattling, loose panels, and gaps for a safer, quieter appliance. What it does:

• Secures exterior and interior panels, brackets, and trim pieces
• Restores proper fit where missing or stripped screws cause movement or noise
• Helps maintain appliance alignment and prevents parts from vibrating loose
• Used for general-purpose repairs on compatible GE appliances

• Disconnect power or unplug the appliance before performing any internal repairs
• Use the correct screwdriver bit and avoid overtightening to prevent stripping threads
• Keep remaining screws in a labeled container for future service
• If a screw does not seat easily, stop and verify correct fit to avoid damage

This euro standoff kit provides the mounting hardware used to secure trim panels and components on compatible appliances, restoring proper panel alignment and preventing rattles or loose trim. It's a direct-fit replacement for the listed part number. What it does:

• Replaces worn or damaged mounting standoffs that hold panels or trim in place
• Restores secure panel attachment to reduce vibration, rattling, or misalignment
• Helps maintain proper spacing between panels and cabinet for correct fit and finish
• Designed to match the original part's fit and function for reliable repair

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove affected trim/panel carefully to access standoffs; retain screws and hardware
• Install standoffs in the original locations and tighten screws until snug — do not overtighten
• If alignment issues persist after replacement, check adjacent clips, fasteners, and mounting surfaces

This is a refrigerator handle kit. This kit includes one handle that has a stainless steel finish. The purpose of the handle is to provide a piece to hold onto to open the refrigerator door. The handle could become damaged if it comes into forceful impact with another object. It can become dented or scratched. If the stainless steel finish begins to wear over time, this part will be a high-quality replacement. Save the screws from the original handle to install the one one. Replacing this part is very easy and can be done quickly by following the installation instructions. Some people may wish to wear work gloves to protect their hands during the replacement process.This specific handle kit is compatible with refrigerator units that are manufactured by the General Electric brand, including Hotpoint and RCA. It is sold individually and is sourced directly from the manufacturer.

This is a #10-32 x 3/4 truss-head screw designed to fasten small appliance panels and components securely. It replaces missing or worn fasteners to restore stable mounting and reduce rattles or movement. What it does:

• Secures trim, control panels, brackets, and small assemblies
• Restores tight mounting to stop panel vibration or rattling
• Keeps electrical and mechanical components properly aligned
• Works where a #10-32 machine screw with a short 3/4" length and truss head is required

• Disconnect power before working on the appliance
• Use the correct screwdriver or nut driver to avoid stripping the head
• Tighten until secure; avoid over-tightening which can strip threads or crack plastic
• Keep removed hardware organized for reinstallation

This screw set contains #10-32 thread fasteners used to secure appliance panels and components. It provides direct-fit replacement screws to restore proper fastening and stop loose or rattling parts. What it does:

• Replaces missing or damaged #10-32 screws used on appliances
• Secures panels, brackets, trim pieces, and internal components
• Helps eliminate rattling, vibration noise, and loose fittings
• Restores factory fastening for safe, stable operation

• Disconnect power and water before servicing the appliance
• Keep small parts organized and use a magnetic tray to avoid loss
• Use the correct driver to avoid stripping screw heads; do not overtighten

This refrigerator door gasket creates an airtight seal between the door and cabinet to keep cold air in and moisture out. Replace a torn, warped, or leaky gasket to restore proper sealing and consistent temperatures around the door opening. What it does:

• Seals the door perimeter against the cabinet to limit air leaks
• Helps maintain interior temperature and reduce condensation or frost near the door
• Supports proper door closing and alignment
• Common symptoms of a failed gasket: visible cracks/tears, door not sealing, condensation or frost at the door edge, warm spots near the door

• One door gasket

• Disconnect power before servicing
• Warm the new gasket (soak in warm water or use low heat) to make it pliable
• Remove the old gasket and clean the retainer/channel thoroughly
• Press the new gasket fully into the retainer; square corners, check for even contact all around, and use gentle low heat to relax waves; allow up to 24 hours for the gasket to conform

Freezer side top hinge shim. For bottom hinge shim use WR2X8593.

Freezer side bottom hinge shim. For top hinge shim use WR2X8592.