Parts for Kitchenaid KFIS20XVMS11: 08 - Freezer Door Parts

This black replacement handle restores a solid, comfortable grip for opening and closing your appliance's door or drawer. Replace a cracked or loose handle to improve safety and refresh the look of the unit.

• Provides the handhold needed to open and close the door or drawer
• Direct replacement for cracked, broken, or wobbly handles
• Helps resolve difficulty opening caused by a missing or damaged handle
• Restores a clean, factory look

• Disconnect power before servicing
• Access the handle's mounting screws from the inside of the door/drawer; remove screws, swap the handle, and reinstall
• Support the door/drawer while loosening/tightening fasteners
• Do not overtighten; verify smooth operation after installation

The Freezer Door Gasket is an OEM part for Whirlpool refrigerators. It provides a secure seal around the freezer door, helping to maintain the internal temperature and ensure efficient operation by preventing warm air from entering the freezer compartment.

You should replace the freezer door gasket if it becomes worn out, torn, or damaged. Causes of a bad door gasket can include general wear and tear, frequent opening and closing of the freezer door, or exposure to extreme temperatures. 

Symptoms of a bad freezer door gasket include:

• Frost buildup inside the freezer
• The freezer not maintaining a consistent temperature
• Increased energy consumption
• The freezer door not closing properly or sealing tightly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Door Handle Mounting Screw is an OEM part for Whirlpool refrigerators. It secures the door handle to the refrigerator door.

Causes of a bad door handle mounting screw can include wear and tear over time, improper installation, or excessive force applied to the handle. These factors can result in a loose or wobbly handle, compromising the functionality and aesthetics of your refrigerator.

Symptoms of a bad door handle mounting screw may include:

• A loose or unstable handle
• Difficulty in opening or closing the refrigerator door
• The handle becoming detached

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This replacement bracket provides a secure mounting point for a designated component in your appliance. It keeps parts properly supported and aligned, helping the unit operate smoothly without vibration or shifting.

• Supports and anchors a specific part or assembly in the correct position
• Helps prevent vibration, rattling, and premature wear from movement
• Maintains alignment for consistent, reliable operation
• Replace if bent, cracked, or missing; symptoms can include loose components or unusual noise

• Disconnect power; shut off water or gas supply if applicable
• Access the bracket location per your model's service information and note the original orientation
• Transfer any screws, clips, or grommets from the old bracket to the new one
• Tighten fasteners evenly and verify alignment before restoring power

This freezer upper drawer glide replaces the worn slide that guides the upper freezer basket in and out. Restores smooth, aligned drawer movement and reduces binding or scraping caused by a cracked or damaged glide. What it does:

• Supports and guides the upper freezer basket/drawer for smooth travel
• Helps keep the drawer aligned to prevent binding or coming off track
• Replaces cracked, worn, or broken glide rails that impede movement
• Typical symptoms include stiff opening/closing, jamming, scraping noises, wobble, or visible damage

• 1 upper freezer drawer glide

• Disconnect power before servicing; remove food and freezer baskets
• Pull the drawer out and remove fasteners/clips securing the glide; note orientation
• Transfer any stops/spacers from the old glide as needed and reuse existing hardware
• Secure the new glide, reinstall the drawer, and test for smooth operation

This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.

• Fastens covers, trims, brackets, and internal parts to the cabinet/frame
• Used wherever a #8-18 x 5/8 screw is specified
• Replace if the original is missing, corroded, stripped, or will not tighten
• Symptoms: loose or rattling panels, gaps, or hardware that backs out

• Disconnect power; shut off gas/water before servicing
• Match thread and length; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly—do not overtighten
• Inspect and replace damaged clips or tabs before securing