Parts for Maytag JCB2585WEP01: 06 - Freezer Door Parts

Reduces contaminants for cleaner, better-tasting water and ice. Replace every 6 months or when indicator light activates. Verify fit by model number.

Replace your refrigerator's door handle if it's cracked, broken, or missing. This handle installs on the refrigerator door for easy opening and closing.

This handle stud is the mounting hardware that secures your refrigerator door handle to the door. It provides the threaded connection point that holds the handle firmly in place. Replace if your door handle is loose, wobbly, or has fallen off completely.

This replacement screw secures panels, brackets, and internal components in Whirlpool-built appliances. Use it to replace missing or stripped hardware to restore a snug fit, reduce rattling, and maintain proper alignment. What it does:

• Fastens components to the appliance cabinet or frame
• Helps maintain alignment and proper clearances
• Reduces vibration-related noises from loose or missing hardware
• Common replacement when a screw is lost, corroded, or threads are damaged

• 1 screw

• Disconnect power before service; for gas appliances, also shut off gas supply
• Start threading by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly without overtightening to prevent stripping
• Inspect and replace any worn clip/nut or damaged threads

Horizontal metal rod that secures glass shelf panels inside your refrigerator door. Replace if broken, bent, or missing to prevent shelf slippage.

Top door hinge thimble bearing supports the upper refrigerator hinge for smooth door operation. Replace if cracked, worn, or causing popping noises.

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.

The door stop bracket is a metal or plastic bracket that mounts to the appliance cabinet or door frame to physically limit how far the door can open, protecting the hinges and surrounding cabinetry. It works alongside other door stop components to keep the door from swinging past a safe angle. Replace this bracket if it is bent, cracked, missing, or your door swings open too far and is stressing the hinges.

Ice bin won't release or latch broke? This ice bin latch spring provides tension to secure the ice container properly. Easy 10-minute DIY fix.

This replacement cabinet screw secures panels, brackets, and ducts in Whirlpool-built appliances so components stay aligned and secure. Replacing missing or stripped hardware helps reduce vibration, rattling, and gaps that can affect performance.

• Fastens panels, brackets, and internal components in the appliance cabinet
• Helps maintain proper alignment and reduce vibration or rattling noises
• Restores a tight fit where original hardware is missing, damaged, or stripped
• Typical symptoms: loose paneling, buzzing/rattling sounds, or parts that won't stay fastened

• Disconnect power; for gas models, also shut off the gas supply
• Replace one fastener at a time to preserve alignment and match to the original hardware
• Use the correct driver; start threads by hand to avoid cross-threading
• Do not overtighten into sheet metal