Parts for Ge GBSC0HCXARBB: 02 - Freezer Section Parts

8-18 CA HX 1/2 S

Sheet metal screw secures refrigerator panels, trim, and brackets. Replace missing, stripped, or corroded screws to restore proper fit and assembly.

This evaporator cover protects the refrigerator evaporator assembly and helps direct airflow for consistent cooling. It replaces a cracked, warped or missing cover to reduce interference with airflow and help prevent ice build-up on the evaporator. What it does

• Shields the evaporator coil and related components from damage and debris
• Helps direct airflow from the evaporator to the freezer/refrigerator compartments
• Can reduce frost buildup caused by a damaged or missing cover
• May stop rattle or contact noises caused by a loose or broken cover

• One evaporator cover

• Disconnect power to the appliance before starting any repair
• Remove interior panels and any mounting screws or clips to access the evaporator housing
• Handle the cover carefully—plastic tabs can be brittle on older units
• If clips or screws are corroded or broken, replace them separately

This self-adhesive foam strip replaces worn or missing foam used to seal gaps and reduce vibration in refrigerators and freezers. It helps improve insulation and quiet operation by filling small openings where air or moisture can pass. What it does:

• Provides a compressible seal to reduce air leaks that can cause frost buildup or uneven cooling
• Dampens vibration and rattling between panels or trim pieces
• Helps block dust and moisture from entering cabinet seams
• Can restore proper door and panel contact where original foam has deteriorated

• Unplug the appliance before starting any repair
• Clean and dry the mounting surface; remove backing and press strip firmly in place
• Trim to fit with scissors or utility knife as needed; avoid stretching the foam
• Only replace foam where original is missing or damaged; follow OEM placement for best seal

Self-adhesive foam strip seals gaps along doors and panels to reduce air leaks and vibration. Replace when worn or compressed to restore efficiency.

Rubber grommet that mounts and cushions the evaporator or condenser fan motor. Replace if cracked, worn, or missing to prevent vibration and noise.

Secures water tubing to fittings in refrigerators and dishwashers. Replace if leaking, tubing slips off, or clamp is cracked. Confirm fit with model number.

Mounting screw for refrigerator and freezer internal components. Replace if stripped, missing, or damaged during repairs. Secures panels and parts.

Refrigerator freezer light shield cover protects the bulb and diffuses light. Replace if cracked, yellowed, or broken to restore proper illumination.

Mounting screw for dryers, refrigerators, and side-by-side units. Replaces lost, stripped, or damaged screws during appliance repairs or maintenance.

The GE Door Light Switch is an OEM Replacement Part that serves as the Freezer Door Fan and Light Switch. The switch is made from metal, wiring, and plastic. It plays an essential role in energy conservation by turning off the light when the refrigerator or freezer door is closed

Over time, the door light switch can wear out or fail due to frequent use, exposure to moisture, or electrical issues. When this happens, the interior light may not function correctly, which can hinder visibility inside the refrigerator.

Symptoms of a bad door light switch may include:

• Interior light not turning on when the door is opened
• Interior light not turning off when the door is closed
• Flickering or intermittent operation of the interior light

This switch is compatible with select GE and Hotpoint models.

The Light Bulb (40W) is an OEM component for GE refrigerators. As an essential task lamp, it illuminates the interior of the refrigerator and freezer compartments. 

All light bulbs will eventually burn out with consistent use over many years. Vibration during compressor cycles can also potentially disrupt bulb filaments faster. 

Symptoms of a burnt out refrigerator light bulb include:

• Dim or no light illuminating inside refrigerator shelves  
• Shadows and dark spots making it difficult to find items
• Higher utility costs from leaving the door open to see inside

This bulb is also compatible with refrigerators from brands like Hotpoint, RCA, and some Kenmore models. 

The Light Socket is an OEM part for GE refrigerators. It is responsible for holding the refrigerator's light bulb and ensuring it receives power to illuminate the interior when the door is opened.

You should replace the light socket if it becomes faulty. Causes of a bad light socket can include wear and tear from regular use, electrical issues such as short circuits or power surges, and corrosion from moisture exposure.

Symptoms of a bad light socket include:

• The refrigerator light not turning on when the door is opened
• Flickering or intermittent light operation
• Visible damage or corrosion on the socket
• The light bulb not fitting securely or falling out

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Rattling noise or warm temps? A broken evaporator fan blade disrupts air circulation. This repair takes 30-45 minutes with basic tools and our video guide.

Wire tie retainer for refrigerators. Secures and organizes internal wiring. Replace if cracked, broken, or missing to keep wires properly bundled.

Rubber grommet that mounts and cushions the evaporator or condenser fan motor. Replace if cracked, worn, or missing to prevent vibration and noise.

Secures the evaporator fan assembly to the freezer compartment wall. Replace this mounting bracket if cracked, broken, or missing hardware slots.

Mounting screw for freezer interior components and panels. Replace if stripped, corroded, or missing to secure shelves, racks, or trim properly.

Fix a warm fridge or freezer ice buildup. This defrost heater melts frost on evaporator coils to restore cooling. Moderate DIY repair, 1-2 hours.

Ice maker not filling or water spilling? This fill cup directs water into the ice maker mold for proper ice production. Simple clip-on install.

Freezer working but fridge not cooling? Coils frozen solid? Replace your defrost thermostat. Mounts on evaporator to control defrost heater cycle.

Freezer cold but fridge warm? This evaporator fan motor circulates air across coils to maintain even cooling. DIY-friendly repair, typically 30 minutes.

The Lid Bumper is an OEM part for GE refrigerators. It is designed to provide cushioning and protection for the refrigerator lid, preventing damage and ensuring smooth, quiet closing. 

Causes of a bad Lid Bumper can include deterioration over time due to frequent use, exposure to temperature variations, or damage from accidental impacts. A worn or damaged bumper may no longer provide adequate cushioning, leading to potential damage to the lid or the refrigerator itself.

Symptoms of a bad Lid Bumper include:

• The refrigerator lid closing too hard
• Unusual noises when closing the lid
• Visible wear or cracks on the bumper

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

Secures the condenser fan motor in position. Replace this bracket if cracked, bent, or causing excessive vibration to restore stable mounting.