Parts for Ge GTS18DCMCRWW: 02 - Freezer Section Parts

Plastic extension tube that connects the water valve to your ice maker. Replace if cracked, broken, or missing to restore proper water flow path.

Ice overflowing freezer or ice maker won't shut off? Replace the missing or broken ice bucket. Installs in minutes, no tools required.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

This plug housing switch is the molded connector that secures and protects the appliance power cord where it plugs into the appliance. It restores a stable, insulated connection and helps prevent arcing or intermittent power. What it does:

• Houses and secures the power cord terminals to maintain a reliable electrical connection
• Protects exposed terminals from moisture and debris to reduce shorting or arcing risk
• Replaces cracked, melted, or loose housings that can cause intermittent power or appliance failure
• Commonly used when the appliance won't power on or power is intermittent at the cord connection

• One plug housing switch

• Disconnect power at the breaker or unplug the appliance before servicing
• Inspect the power cord and terminal screws for damage; replace cord if terminals are burned or wires are compromised
• Hand tools typically required; ensure terminals are fully seated and screws tightened to secure the cord

Refrigerator not cooling but freezer works? A failed evaporator fan motor stops cold air circulation. DIY-friendly repair with basic tools in 30-60 minutes.

Freezer fan loud or not spinning? This evaporator fan blade circulates cold air over the coils. DIY-friendly repair with our video guide.

The Lid Bumper is an OEM part for GE refrigerators. It is designed to provide cushioning and protection for the refrigerator lid, preventing damage and ensuring smooth, quiet closing. 

Causes of a bad Lid Bumper can include deterioration over time due to frequent use, exposure to temperature variations, or damage from accidental impacts. A worn or damaged bumper may no longer provide adequate cushioning, leading to potential damage to the lid or the refrigerator itself.

Symptoms of a bad Lid Bumper include:

• The refrigerator lid closing too hard
• Unusual noises when closing the lid
• Visible wear or cracks on the bumper

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Rubber grommet cushions and stabilizes the evaporator fan motor in your refrigerator. Replace if cracked, worn, or missing to reduce vibrations and noise.

Fix a warm fridge or freezer ice buildup. This defrost heater melts frost on evaporator coils to restore cooling. Moderate DIY repair, 1-2 hours.

This replacement defrost heater warms the freezer's evaporator area during the automatic defrost cycle. It melts accumulated frost so air can circulate, helping maintain stable temperatures and preventing ice buildup on the back wall.

• Heats the evaporator to clear frost and ice during defrost
• Helps keep airflow passages and the defrost drain path open
• Common symptoms of a failed heater: heavy frost on the back panel/coils, poor cooling or warm sections, fan noise from ice contact, cooling returns temporarily after a manual defrost
• Typically located behind the rear freezer panel

• Disconnect power before servicing; wear cut-resistant gloves
• Access the evaporator by removing the freezer's rear panel; thaw heavy ice before removal
• Transfer any clips/brackets and route wires exactly as original, keeping them away from plastic parts
• After installation, ensure wiring connections are secure and the heater is not contacting plastic surfaces

Fixes warm fridge with cold freezer caused by frosted evaporator coils. This defrost thermostat regulates defrost cycles. Moderate DIY repair, 1-2 hours.

This holder element assembly secures the appliance's heating element in the correct position so the element stays stable for consistent operation and safe performance. It's a direct-fit replacement for worn or damaged holders. What it does:

• Secures and supports the heating element inside the appliance to maintain proper alignment
• Prevents element sagging or contact with other components that can cause noise or arcing
• Helps reduce vibration and movement that can lead to intermittent heating
• Common symptom: visible holder damage, loose or shifted element, unusual noise during operation

• Disconnect power (unplug or switch off breaker) before starting any repair
• Allow appliance and element to fully cool before handling
• Handle the element and holder carefully to avoid bending or damaging the element

Drain trough that channels defrost water to the drain pan in your top-mount refrigerator. Replace if cracked, warped, or missing to prevent leaks.

Replacement mounting screw for securing panels, trim, and internal brackets. Needed when original fasteners are missing, stripped, or damaged.

Ice maker not filling or water dispenser not working? This refrigerator water inlet valve controls water flow to both. DIY install in 10 minutes.

Secures trim and panels in your refrigerator. Replace when broken clips cause loose parts or rattling. Verify fit with your model number.

Secures refrigerator wiring to prevent chafing and vibration noise. Replace when damaged or missing to keep harnesses organized. Confirm fit by model.

Plastic water line that connects the water inlet valve to the ice maker. Replace if cracked, leaking, or damaged. Includes installation video.

Secures water tubing or wiring to your refrigerator cabinet. Replace if missing or damaged to prevent vibration, rubbing, or leaks. Confirm fit.

Ice maker not filling or water spilling? This fill cup directs water into the ice maker mold for proper ice production. Simple clip-on install.

Ice maker not producing ice or stopped working? This ice maker kit restores ice production. Includes full assembly for harvesting and ejecting ice.