Parts for Ge PDSF0MFXBRCC: 02 - Freezer Section Parts

Purifies water before reaching your dispenser and ice maker. Replace every 6 months for clean, safe drinking water. Verify fit with your model number.

8-18 CA HX 1/2 S

Sheet metal screw secures refrigerator panels, trim, and brackets. Replace missing, stripped, or corroded screws to restore proper fit and assembly.

This evaporator cover protects the refrigerator evaporator assembly and helps direct airflow for consistent cooling. It replaces a cracked, warped or missing cover to reduce interference with airflow and help prevent ice build-up on the evaporator. What it does

• Shields the evaporator coil and related components from damage and debris
• Helps direct airflow from the evaporator to the freezer/refrigerator compartments
• Can reduce frost buildup caused by a damaged or missing cover
• May stop rattle or contact noises caused by a loose or broken cover

• One evaporator cover

• Disconnect power to the appliance before starting any repair
• Remove interior panels and any mounting screws or clips to access the evaporator housing
• Handle the cover carefully—plastic tabs can be brittle on older units
• If clips or screws are corroded or broken, replace them separately

This self-adhesive foam strip replaces worn or missing foam used to seal gaps and reduce vibration in refrigerators and freezers. It helps improve insulation and quiet operation by filling small openings where air or moisture can pass. What it does:

• Provides a compressible seal to reduce air leaks that can cause frost buildup or uneven cooling
• Dampens vibration and rattling between panels or trim pieces
• Helps block dust and moisture from entering cabinet seams
• Can restore proper door and panel contact where original foam has deteriorated

• Unplug the appliance before starting any repair
• Clean and dry the mounting surface; remove backing and press strip firmly in place
• Trim to fit with scissors or utility knife as needed; avoid stretching the foam
• Only replace foam where original is missing or damaged; follow OEM placement for best seal

Self-adhesive foam strip seals gaps along doors and panels to reduce air leaks and vibration. Replace when worn or compressed to restore efficiency.

Rubber grommet that mounts and cushions the evaporator or condenser fan motor. Replace if cracked, worn, or missing to prevent vibration and noise.

Secures water tubing to fittings in refrigerators and dishwashers. Replace if leaking, tubing slips off, or clamp is cracked. Confirm fit with model number.

Protective insulation sleeve for refrigerator wiring harnesses. Installs around electrical wiring to prevent heat damage and wear. Replace if cracked or torn.

Mounting screw for refrigerator and freezer internal components. Replace if stripped, missing, or damaged during repairs. Secures panels and parts.

Refrigerator freezer light shield cover protects the bulb and diffuses light. Replace if cracked, yellowed, or broken to restore proper illumination.

Mounting screw for dryers, refrigerators, and side-by-side units. Replaces lost, stripped, or damaged screws during appliance repairs or maintenance.

The Temperature Sensor Seal is an OEM part for GE refrigerators. This seal is designed to protect the temperature sensor from moisture and other environmental factors that could affect its accuracy and longevity. By providing a barrier against the hars

Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.

The GE Door Light Switch is an OEM Replacement Part that serves as the Freezer Door Fan and Light Switch. The switch is made from metal, wiring, and plastic. It plays an essential role in energy conservation by turning off the light when the refrigerat

The Light Bulb (40W) is an OEM component for GE refrigerators. As an essential task lamp, it illuminates the interior of the refrigerator and freezer compartments. 

All light bulbs will eventually burn out with consistent use over many yea

The Light Socket is an OEM part for GE refrigerators. It is responsible for holding the refrigerator's light bulb and ensuring it receives power to illuminate the interior when the door is opened.

You should replace the light socket if it b

Rattling noise or warm temps? A broken evaporator fan blade disrupts air circulation. This repair takes 30-45 minutes with basic tools and our video guide.

Wire tie retainer for refrigerators. Secures and organizes internal wiring. Replace if cracked, broken, or missing to keep wires properly bundled.

Rubber grommet that mounts and cushions the evaporator or condenser fan motor. Replace if cracked, worn, or missing to prevent vibration and noise.

Secures the evaporator fan assembly to the freezer compartment wall. Replace this mounting bracket if cracked, broken, or missing hardware slots.

Secures the evaporator fan assembly behind the rear freezer panel. Replace if cracked, rusted, or missing to restore proper fan mounting and clearance.

Mounting screw for freezer interior components and panels. Replace if stripped, corroded, or missing to secure shelves, racks, or trim properly.

Fix a warm fridge or freezer ice buildup. This defrost heater melts frost on evaporator coils to restore cooling. Moderate DIY repair, 1-2 hours.

Ice maker not filling or water spilling? This fill cup directs water into the ice maker mold for proper ice production. Simple clip-on install.

The Defrost Thermostat is an OEM replacement part designed for use in GE refrigerators. This component acts as a safety device in the refrigerator's defrost system, preventing the freezer from overheating during the defrost cycle. It works by monit

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Fridge warm but freezer cold? Your evaporator fan motor likely failed. Fixes air circulation issues. Moderate DIY repair with basic tools.

The Lid Bumper is an OEM part for GE refrigerators. It is designed to provide cushioning and protection for the refrigerator lid, preventing damage and ensuring smooth, quiet closing. 

Causes of a bad Lid Bumper can include deterioration o

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.