Parts for Ge ZSEB420DYB: 04 - Freezer Section Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

Fix a refrigerator that's not cooling properly or has excessive frost buildup with this evaporator coil. Handles heat removal in side-by-side models.

This foam block fits around the refrigerator evaporator to insulate and stabilize the evaporator assembly, helping reduce vibration and limit unwanted air flow for more consistent cooling performance. What it does

• Provides cushioning and vibration dampening for the evaporator assembly.
• Helps seal gaps around the evaporator to support proper airflow and temperature control.
• Reduces rattle and noise caused by contact between the evaporator and surrounding cabinet parts.
• Supports correct evaporator placement to prevent ice buildup from air leaks.

• Disconnect power to the appliance before starting any repair.
• Handle the foam gently to avoid tearing; position it as shown in the evaporator area or OEM diagram.
• Use only OEM-recommended clips or fasteners; do not rely on solvents or non-approved adhesives unless specified by the manufacturer.

Secures the quick connect duct assembly in your refrigerator. Replace if the bracket is cracked, broken, or missing to properly mount ductwork components.

A replacement auger motor assembly that powers the ice-dispensing auger so you can reliably move ice from the bin to the dispenser. Fits 36" and 42" dispenser configurations. What it does

• Turns the auger to feed ice through the dispenser chute
• Restores ice dispensing when the auger fails to rotate
• Stops unwanted motor noise or humming when the motor is the fault
• Works with the dispenser drive components to maintain consistent ice flow

• One auger motor assembly

• Disconnect power to the appliance before starting any repair
• Remove dispenser/ice-bin components and trim panels to access the motor per model instructions
• Handle electrical connectors and wiring gently; ensure secure connections before testing
• If water is present near the motor area, dry thoroughly and verify seals to prevent electrical shorts

Halogen bulb for refrigerator light column. Replace when interior lighting fails to restore bright, even illumination. Verify fit with your model number.

Flexible drain tube that routes defrost water from the evaporator to the drain pan. Replace if cracked, split, clogged, or missing to prevent leaks.

Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.

The Lid Bumper is an OEM part for GE refrigerators. It is designed to provide cushioning and protection for the refrigerator lid, preventing damage and ensuring smooth, quiet closing. 

Causes of a bad Lid Bumper can include deterioration over time due to frequent use, exposure to temperature variations, or damage from accidental impacts. A worn or damaged bumper may no longer provide adequate cushioning, leading to potential damage to the lid or the refrigerator itself.

Symptoms of a bad Lid Bumper include:

• The refrigerator lid closing too hard
• Unusual noises when closing the lid
• Visible wear or cracks on the bumper

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Mounting screw for refrigerator interior components and panels. Replace if stripped, missing, or damaged during service to secure parts properly.

Fix loud fan noise and poor cooling with a new evaporator fan blade. Restores airflow across coils. Moderately difficult install in tight freezer space.

If your refrigerator compartment isn't cooling while the freezer stays cold, the evaporator fan motor likely failed. DIY-friendly repair with video guide.

Secures the evaporator fan motor to the refrigerator cabinet. Replace if your original bracket is bent, broken, or cracked to restore proper mounting.

Secures the evaporator fan shroud to the rear compartment frame. Replace if rusted, cracked, or broken to properly support the fan assembly and alignment.

Mounting screw for refrigerator interior components like fan brackets, ice maker assemblies, and shelving. Replace if stripped, missing, or corroded.

Rubber grommet that seals and cushions where the evaporator fan motor shaft mounts. Replace if cracked, worn, or missing to eliminate noise and vibration.

Size: 8-16 x 2 inch ss.

This cover harness organizes and protects the main wiring inside a side-by-side refrigerator, helping keep electrical connections secure and routed safely for reliable operation. Use it when wiring cover damage or wear exposes connectors. What it does

• Routes and protects internal wiring behind refrigerator panels to prevent chafing and accidental disconnection.
• Secures connector positions so components receive consistent power and signals.
• Common symptom: visible frayed wiring or loose connectors behind the fresh-food/freezer panel.
• Can be a factor when intermittent component operation or wiring-related faults are observed.

• Disconnect power to the appliance before service to avoid shock or damage.
• Remove panels per the OEM service instructions to access the old harness; note connector positions before removal.
• Inspect connectors and adjacent wiring; replace any damaged clips or grommets to prevent future abrasion.

Secures the defrost heater assembly in your refrigerator's freezer section. Replace if the original bracket is cracked, broken, or missing.

Replacement edge trim that covers and protects exposed edges on refrigerator doors or cabinets. Needed when original trim is cracked, broken, or missing.