Parts for Ge XSS25GGPECBB: Freezer Section Parts

Refrigerator plenum gasket seals air duct between fresh food and freezer sections. Replace if torn, cracked, or causing temperature issues. Verify fit with your model number before ordering.

Molded housing that channels cold air from the evaporator across refrigerator compartments. Replace if cracked, damaged, or warped to restore airflow.

Freezer air duct plenum extension that clips into the duct opening to direct airflow. Replace if cracked, broken, or missing to restore proper air circulation.

Seals the evaporator cover to prevent cold air leaks and maintain cooling efficiency. Replace if worn, cracked, or loose. Verify fit with your model number.

Fix frost buildup in your freezer with this evaporator defrost heater. Restores automatic defrost when ice accumulates on coils. Moderate DIY.

Drip trough assembly catches defrost and condensation water in your side-by-side refrigerator. Replace if cracked, broken, or causing leaks.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.

Fix inconsistent temps or ice buildup on evaporator coils? This sensor seal protects accuracy. DIY-friendly with wire splicing. Video guide available.

Replace your refrigerator plenum gasket to restore proper airflow and temperature control. Install when torn, compressed, or causing air leaks. Verify fit with your model number.

Replace your refrigerator's insert plenum if it's cracked, broken, or missing. This internal air distribution component installs in the fresh food section.

Fixes weak airflow and ignition issues in side-by-side refrigerators. This orifice and fan motor assembly restores proper combustion air movement.

Bottom hinge and pin assembly secures the lower refrigerator door, enabling smooth pivoting and alignment. Replace if worn, bent, or broken to restore stability.

Secures mobility components and wheel brackets on side-by-side refrigerators. Replace if screw is missing, stripped, or worn to restore stable mounting.

Front caster assembly that mounts to the bottom of your refrigerator. Replace if cracked, broken, or worn to restore smooth rolling and stability.

White corner cap cover for side-by-side refrigerators. Replaces cracked, broken, or missing corner trim pieces. Restores clean appearance.

Decorative base grille panel that covers the condenser area at the bottom front of your refrigerator. Replace if cracked, broken, or missing.

LED light board assembly illuminates refrigerator interior. Replace when lights dim, flicker, or fail. Verify fit using your model number for compatibility.

Black hinge cover for side-by-side refrigerator doors. Replace if cracked, broken, or missing to restore proper hinge appearance and protection.

Upper hinge pivot pin for side-by-side refrigerator freezer doors. Replace if bent, worn, or missing to restore proper door alignment and swing.

Hex head screw for refrigerator panels, brackets, and assemblies. Replaces missing, stripped, or rusted fasteners to secure components properly.

Freezer light stays on or won't turn on? This door light switch restores interior lighting control. Simple DIY fix in about 15 minutes.

Secures the lower edge of the evaporator assembly inside your refrigerator. Replace if cracked, broken, or missing to restore proper alignment.

Replace missing or stripped #8-18 x 5/8-inch Torx T20 screws in your side-by-side refrigerator. Secures panels, brackets, drawer rails, and trim.

Rattling noise or warm temps? A broken evaporator fan blade disrupts air circulation. This repair takes 30-45 minutes with basic tools and our video guide.

Rubber bumper that cushions and mounts the evaporator fan motor assembly. Replace if cracked, deteriorated, or missing to reduce vibration and noise.

Rubber grommet that seals and cushions where the evaporator fan motor shaft mounts. Replace if cracked, worn, or missing to eliminate noise and vibration.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

Protective cap that covers the evaporator fan motor bearing and housing in freezers and refrigerators. Replace if cracked, broken, or missing to prevent debris.

Replaces the freezer door lever assembly on side-by-side refrigerators. Installs on freezer door. Needed when original lever is broken or cracked.

Replacement door closure spring for refrigerator hinges. Installs on door hinge assembly to provide tension for proper closing. Needed when broken or worn.

Fastens refrigerator panels, brackets, and internal components. Replace this screw if the original is missing, stripped, or damaged to restore secure mounting.