Parts for Ge CFE29TSDBSS: Freezer Shelves Parts

Removes contaminants from your refrigerator's water and ice. Replace every 6 months or when the filter indicator activates. Confirm fit with your model.

Secures components to your appliance chassis for a rattle-free fit. Replace missing, stripped, or corroded screws to keep panels and brackets aligned.

Bottom freezer basket assembly for refrigerators. Installs in lower freezer compartment for organized frozen food storage. Replace if cracked or broken.

Fix a stuck or hard-to-open freezer drawer with this lower drawer gear. Replaces broken teeth causing drawer issues. Easy DIY repair, no tools needed.

Lower drawer gear for bottom-mount refrigerators. Installs on the left side of the freezer drawer assembly. Replace if cracked, broken, or damaged.

The Connector Gear Pinion is an OEM part for GE refrigerators. It is integral to the smooth operation of the freezer drawer, connecting the rail system and allowing the drawer to open and close effortlessly.

Causes of a bad connector gear pinion can include general wear and tear over time, excessive force applied during operation, or debris causing obstructions within the mechanism.

Symptoms of a bad Connector Gear Pinion include:

• Difficulty in opening or closing the freezer drawer
• Unusual noises such as grinding or clicking when operating the drawer
• The drawer not staying aligned or properly seated on the rails
• The drawer getting stuck or not moving smoothly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

If ice isn't ejecting from your ice maker, this crossbar pinion drives the ejector mechanism during harvest. Slides into place and secures with pin.

Secures the crossbar in your refrigerator's interior for stable shelving support. Replace if pin is broken, missing, or worn to restore proper fit.

Secures freezer door panels and trim to prevent rattling and maintain proper seal. Replace when screws are worn, missing, or stripped. Confirm fit with model.

Bottom freezer basket assembly for refrigerators. Installs in lower freezer compartment for organized frozen food storage. Replace if cracked or broken.

This support component helps freezer drawers or shelves slide smoothly in and out of the freezer compartment. Located inside the freezer on the side walls or bottom, replace it when drawers stick, won't slide properly, or have become loose and unstable.

This replacement stopper secures the freezer divider so bins and shelves stay aligned, preventing shifting and gaps that can affect storage. Simple, direct fit for restoring proper divider positioning. What it does:

• Holds the freezer divider in place to keep bins and shelves aligned
• Prevents the divider from sliding or dropping during normal use
• Helps maintain organized cold storage and reduces shifting of contents
• Commonly replaced when cracked, broken, or missing

• One freezer divider stopper

• Remove food and empty the affected bin before starting
• Usually snaps into the divider track or mounting slot; inspect mating surfaces for damage
• Use basic hand tools only if needed; do not force the part into place

This push-in fastener secures trim, panels, and plastic components on compatible appliances to prevent rattling and hold parts in place. Simple clip design keeps panels aligned without screws or specialized hardware. What it does

• Holds plastic trim, interior panels, and lightweight assemblies in place
• Replaces worn or broken push retainers that cause loose or vibrating panels
• Helps restore proper fit of door liners, kick plates, and interior housings
• Commonly used where a snap-in plastic retainer is required

• Push into the matching hole until the head seats flush; no tools typically required
• Inspect mating hole and surrounding material for damage before installation
• Remove power and follow appliance safety instructions when working near electrical components
• If fastener does not seat correctly, confirm correct part and hole size before forcing

Right-hand slide bracket assembly that mounts to the cabinet side to support and guide refrigerator or freezer drawers. Replace if cracked or worn.

Left slide bracket assembly supports and guides refrigerator drawers for smooth operation. Replace when drawers stick, misalign, or won't close properly. Confirm fit with your refrigerator model number before ordering.

Right-hand slide bracket for refrigerator freezer baskets. Replace if cracked, broken, or basket won't slide smoothly. Secures with two screws.

Supports and guides your upper freezer basket for smooth sliding. Replace when cracked or worn to restore easy access and proper alignment. Easy install.

Left-hand bracket that secures the freezer basket slide rail in top freezer refrigerators. Replace if cracked, broken, or missing to restore stability.

Lower freezer drawer slide enables smooth gliding access to your freezer compartment. Replace if drawer sticks, wobbles, or doesn't glide properly. Confirm fit with your model number before ordering.

Left-side lower freezer drawer slide for bottom-mount refrigerators. Replaces worn or damaged slides with seized bearings, broken tabs, or missing parts.

Right-hand freezer drawer slide holder that secures and guides the drawer for smooth operation. Replace if cracked, broken, or worn to restore alignment.

Left-side freezer drawer slide holder secures and guides your refrigerator's freezer drawer. Replace if cracked, broken, or worn to restore alignment.

8-18 x 9/16-inch hex washer head screw secures panels, brackets, and trim in appliances. Replace missing, damaged, or stripped screws for proper fit.

This is a single #10-18 x 3/4 inch flat-head screw used to secure panels and components in appliances. It replaces worn or missing fasteners so parts stay properly mounted and aligned. What it does:

• Fastens appliance panels, brackets, and components with a flat-head finish for flush mounting
• Replaces stripped, rusted, or missing screws that cause loose or rattling parts
• Provides a secure threaded connection for consistent operation
• Compatible where a #10-18 thread, 3/4" length flat-head screw is specified

• One (1) screw, #10-18 x 3/4 in., flat head

• Use the correct screwdriver bit (flat or Phillips depending on head style) and avoid over-tightening to prevent stripped threads
• Disconnect power to the appliance and follow manufacturer safety procedures when accessing internal components
• Dispose of damaged hardware and replace with matching specifications for safe operation

This is a small plastic striker that activates the door light switch when the refrigerator door is closed. It presses against the light switch mechanism to turn the interior light off when the door shuts. Replace this part if your refrigerator light stays on constantly or fails to turn off when the door is closed, which can cause excess heat buildup and higher energy usage.