Parts for Electrolux E23BC79SPS7: Fresh Food Door Parts

The Fresh Food Door Gasket is an OEM replacement part for Frigidaire refrigerators. It creates a seal around the refrigerator door to maintain a consistent temperature by keeping cold air in and warm air out. This helps ensure proper refrigerator conditions and prevents energy loss.

Over time, gaskets can degrade due to wear, exposure to extreme temperatures, or cleaning with harsh chemicals. A damaged or worn gasket may fail to seal properly, affecting the freezer's efficiency and potentially leading to increased energy consumption.

Symptoms of a bad gasket include:

• Frost or ice buildup inside the refrigerator
• Difficulty keeping the refrigerator door fully closed
• Warm air entering the refrigerator, causing temperature fluctuations
• Increased energy bills due to inefficient operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

NOTE: GASKET NOW GRAY, NOT WHITE

This piece replaces the flip-up cover for the cheese/butter compartment on your refrigerator door. It restores a tidy, enclosed spot for butter and small dairy items, helping keep contents contained and easy to access.

• Covers the dairy bin on the fresh food door; flips up for quick access
• Helps contain and protect butter/cheese items to reduce spills and mess
• Replace when cracked, warped, missing, or no longer stays attached/closed
• Designed to fit the designated hinge points for the dairy compartment on applicable models

• Disconnect power before servicing
• Allow plastic parts to warm to room temperature to reduce risk of cracking
• Align door tabs with the hinge posts on the compartment and press until fully seated
• Open and close the door to ensure smooth operation

This door stop is the replacement part that limits door travel and cushions the refrigerator door for smoother closing and reduced impact. It helps restore proper door alignment and prevents the door from hitting the cabinet. What it does:

• Stops or limits door travel to prevent over-opening and cabinet damage
• Cushions door movement to reduce slamming and wear on hinges
• Helps maintain correct door alignment so the seal engages properly
• Commonly used when the door hangs unevenly, slams, or won't stay aligned

• Disconnect power or unplug the appliance if accessing electrical components is required.
• Support the door or remove it before replacing hinge or stop hardware.
• Basic hand tools usually required; keep track of small screws and clips.
• Test door operation and alignment after installation; adjust as needed.

The Door Stop is an essential OEM replacement part for Frigidaire bottom-mount refrigerators. It functions to securely hold the refrigerator door fully open during loading and unloading of food items. 

Causes of a faulty door stop include cracking or warping due to years of resisting door closure force during access. Friction might also wear down moving lever components over time.

Symptoms of a bad door stop are:

• Refrigerator door unable to safely prop fully open  
• Door slowly closing partially while items are retrieved
• Visible wear marks or loss of lubrication where door pivots

This authentic OEM replacement is compatible for Frigidaire, Electrolux and Kenmore models. 

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

Replace the worn bearing that supports your refrigerator's ice-dispenser auger. This bearing helps the auger spin smoothly so cubes travel to the chute, restoring steady ice dispensing and reducing grinding or jamming.

• Supports the auger shaft within the ice bin/dispenser assembly
• Enables smooth rotation to move ice toward the chute
• Wear can cause slow or failed dispensing and squealing/grinding noises
• Fixes issues with a cracked, worn, or seized auger support

• Disconnect power and remove the ice bin before servicing
• Separate the bin front/cover and auger assembly; note the bearing's orientation
• Transfer the new bearing and reuse existing screws/retainer if present
• After reassembly, confirm the auger turns freely by hand before restoring power

This retainer is a small mounting clip that secures interior components so they stay in place and operate reliably. It prevents parts from shifting or rattling during normal use and restores proper alignment. What it does:

• Holds trim, shelves or small appliance components securely to the cabinet or frame
• Prevents rattling, movement, or dislodging of the secured part
• Helps maintain correct alignment for smooth operation
• Common symptom: loose or wobbling trim, shelf, or component that won't stay seated

• Retainer mounting clip

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use appropriate hand tools; this part typically snaps or slides into place but may require a screwdriver or nut driver
• Inspect mating surfaces and surrounding fasteners; replace any damaged clips or broken mounting features

This bin door replaces a damaged or cracked refrigerator storage-drawer door to restore a sealed, secure drawer and keep food organized. It fits the compatible drawer frame and provides a clear, durable cover for the bin. What it does:

• Replaces a broken, cracked, or missing bin door to restore proper storage function
• Helps keep produce and stored items contained and visible
• Prevents drafts and helps maintain interior organization
• Restores the smooth open/close action of the storage drawer

• One replacement bin door

• Disconnect power to the appliance before servicing to avoid electrical hazard
• Remove the drawer and lift or unclip the old door per your model's instructions; installation typically reverses removal
• Handle part carefully to avoid cracking the plastic; use a soft surface when setting the door down

This replacement bin door restores the front panel of a refrigerator crisper or deli drawer, keeping contents contained and improving appearance. It's a direct-fit part when the original door is cracked, broken, or detached. What it does:

• Replaces a cracked, broken, or missing crisper/drawer front to restore proper enclosure and appearance
• Helps keep produce and groceries contained and easier to access
• Reinstates the drawer front's mounting points so the drawer opens and closes correctly
• Matches the OEM shape and fit for a proper seal and alignment when installed

• One bin door (front panel) as shown

• Disconnect power to the appliance or unplug the refrigerator before starting any repairs
• Remove the drawer and any clips or screws holding the door; handle plastic parts carefully to avoid damage
• Reinstall in reverse order, ensuring mounting tabs engage and the door aligns with the drawer

This door bin mounts to the refrigerator door to hold bottles, jars, and condiments. Replacing a cracked or missing bin restores secure on-door storage, prevents spills, and keeps frequently used items organized and easy to access. What it does:

• Provides on-door storage for beverages, condiments, and small items
• Keeps contents more secure when opening and closing the door
• Replace if the bin is cracked, broken, warped, discolored, or missing
• Common symptoms include: bin falls off, won't stay seated, loose fit, or items tipping over

• Remove contents, then lift the old bin straight up to release it from the door tabs/rails
• Align the new bin with the mounting slots and press down until it locks firmly in place
• Check for secure engagement before loading; distribute weight evenly and avoid overloading
• If working near any electrical components, disconnect power for safety

This piece replaces the flip-up cover for the cheese/butter compartment on your refrigerator door. It restores a tidy, enclosed spot for butter and small dairy items, helping keep contents contained and easy to access.

• Covers the dairy bin on the fresh food door; flips up for quick access
• Helps contain and protect butter/cheese items to reduce spills and mess
• Replace when cracked, warped, missing, or no longer stays attached/closed
• Designed to fit the designated hinge points for the dairy compartment on applicable models

• Disconnect power before servicing
• Allow plastic parts to warm to room temperature to reduce risk of cracking
• Align door tabs with the hinge posts on the compartment and press until fully seated
• Open and close the door to ensure smooth operation

This replacement part is a set screw, and it is intended for use in different types of appliances. This is a genuine replacement part made by Frigidaire. This screw set is compatible in many different areas of the appliance. Screws are typically used for keeping parts of the machinery secure and in place. It is possible that screws can become loose over time and need to be replaced. A new screw set might be needed if the user notices parts of the appliances are becoming loose or are falling off. This can be due to screws becoming stripped over time or if the appliance is bumped during transport. It is typically easy to replace screws. Simply remove the old screw and replace it with a new part. The only tools needed for this repair are a screwdriver and possibly pliers if the damaged screw is stuck in place.Note that this is a genuine OEM replacement part and is sourced from the manufacturer. This set screw is sold individually.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Hinge Pin is an OEM part for Frigidaire refrigerators. It is responsible for supporting the mullion or flapper, which is the vertical strip that divides the refrigerator doors. It provides smooth movement and proper alignment of the mullion, allowing it to pivot easily for access to both compartments while maintaining an airtight seal when closed.

Causes of a bad hinge pin can include wear and tear over time, accidental damage, or improper handling. A damaged or worn-out hinge pin may result in difficulties in opening or closing the mullion.

Symptoms of a bad Hinge Pin include:

• Difficulty in opening or closing the doors
• Excessive play or wobbling of the mullion
• Failure to maintain a proper seal between door
• Unusual noises during use

This OEM Frigidaire part can also be used on select Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore models.

This replacement guide aligns and supports a moving component so it travels on its intended path without binding. Replacing a worn or broken guide restores smooth operation and helps prevent scraping, jamming, or premature wear of connected parts.

• Keeps the associated rack, drawer, or panel centered and properly aligned during movement
• Provides a track/stop for the mating part to follow
• Reduces friction and noise for smoother sliding
• Typical failure signs: sticking, uneven travel, scraping noises, or visible cracks/broken tabs

• Disconnect power; also shut off water or gas
• Remove the associated assembly to access the guide and note its orientation
• Reuse original screws/clips and tighten securely without overtightening
• Test movement after installation; replace worn mating rails or rollers if needed

The Flipper Mullion Assembly is an OEM part for Frigidaire refrigerators. It is an exterior part that seals the refrigerator door and houses the water and ice dispenser on select models. The flipper mullion assembly attaches both side by side doors together and operates the dispenser and door functions.

Causes of a bad mullion assembly can include damage from door impacts, wear from years of door swing motions, or failure of seals or gaskets.

Symptoms of a bad Flipper Mullion Assembly include:

• Gaps or air leaks around the refrigerator doors when closed
• Loose, sagging or misaligned doors
• Dispenser components like the water valve not functioning properly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
 

The Flapper Door Center Hinge is an OEM part for Frigidaire refrigerators. This hinge is essential for the proper operation of the flapper door, which helps seal the gap between the refrigerator doors when they are closed, ensuring efficient cooling and energy use.

Over time, the center hinge can wear out or become damaged due to regular opening and closing of the refrigerator doors. Accumulation of dirt, dust, or debris, as well as physical impact, can also contribute to hinge failure.

Symptoms of a bad flapper door center hinge include:

• The flapper door not closing properly
• Gaps between the refrigerator doors
• Increased energy consumption due to cold air escaping
• The refrigerator doors not aligning correctly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Air Filter is an OEM part for Frigidaire refrigerators designed to enhance the air quality inside the refrigerator, ensuring that food stays fresh and odor-free.

The Air Filter helps to remove unwanted odors and impurities from the refrigerator's circulating air. It absorbs and neutralizes common food odors, keeping your fridge smelling clean and pleasant. The activated carbon filter is 7 times more effective than baking soda at removing odors. 

For best results, change filter every 6 months. 
Color: Black. 
Measures about 7 inches wide by 5 inches deep. 

Symptoms of a bad air filter include:

• Lingering food odors inside the refrigerator
• Increased presence of stale or unpleasant smells
• Decreased effectiveness in eliminating odors

Replace your Air Filter with this genuine part to ensure a clean and fresh-smelling refrigerator. This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This replacement trim piece secures and finishes the refrigerator air filter door, restoring a clean appearance and proper fit. It helps keep the filter covered and aligned for normal airflow and appearance. What it does:

• Replaces cracked, chipped or missing trim that prevents the air filter door from seating properly
• Helps hold the air filter door in position so the filter stays covered
• Restores a finished look to the refrigerator interior where the filter door sits
• Reduces gaps that can allow the filter to move or look misaligned

• One air filter door trim piece

• Generally snaps or screws into place—inspect existing fasteners and alignment before removing old trim
• Use basic hand tools as needed; keep small parts and fasteners for reassembly
• Handle gently to avoid damaging the surrounding plastic or filter housing

The air filter housing covers and protects the air filter.

The Right Door Closer is an OEM part for Frigidaire refrigerators. It is responsible for ensuring that the refrigerator door closes securely and maintains a proper seal, keeping the cold air inside and your food fresh.

A bad right door closer can be caused by wear and tear, damage, or misalignment. When the closer becomes faulty, it can result in issues such as a loose or sagging door, difficulty in closing the door properly, or a compromised seal that leads to temperature fluctuations.

Symptoms of a bad right door closer include:

• Door not closing or sealing properly
• Condensation or frost buildup inside the refrigerator
• Noisy or squeaking door operation

Replace your faulty right door closer with this genuine OEM part to restore your refrigerator door. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This left-hand door closer replaces the refrigerator/freezer door closer that helps the door swing closed smoothly and stay aligned for a proper seal. Restores reliable closing and reduces door sag or misalignment. What it does:

• Guides and supports the left-side door as it closes to prevent slamming and ensure proper latch engagement
• Helps maintain an even seal to preserve internal temperature and reduce energy loss
• Reduces door sag, rubbing, or uneven gaps caused by worn or broken closers
• Works with the existing hinge/door hardware to control door motion

• High-level replacement — remove the door trim/inner panel to access the closer if required
• Keep screws and brackets organized; verify orientation for left-hand side before fastening
• Disconnect power to the appliance or follow manufacturer's safety guidance when working near electrical components

This small rubber door bumper cushions and aligns the refrigerator door to reduce slamming and wear. It restores smooth closing and helps keep the door sealed for proper cooling. What it does:

• Absorbs impact when the door closes to prevent hard bangs and protect cabinet surfaces
• Keeps the door properly spaced to help maintain a consistent seal
• Reduces rattling or vibration caused by loose or worn bumpers
• Simple, low-profile part used at door contact points or stops

• One replacement bumper

• Power is off if working near electrical components; follow appliance safety precautions
• Remove the old bumper by pulling it from its mounting hole; press the new bumper firmly into place until seated
• Use gloves to protect your hands; avoid using excessive force or tools that could damage trim
• Replace with the exact OEM part number for proper fit and function

This genuine replacement screw secures appliance components and restores proper fit and stability. Use it to replace a missing or damaged fastener and stop panels, trim, or parts from shifting or rattling during normal use. What it does:

• Fastens and holds panels, brackets, or small components in place
• Restores secure attachment when an original screw is missing, damaged, or stripped
• Helps eliminate vibration, rattling, or loose-fitting parts
• Matches the OEM fit and function for reliable reassembly

• Use correct screwdriver or driver bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Disconnect power and remove food or contents from appliance areas as needed before servicing
• If fastener threads are damaged, replace with the exact OEM screw rather than forcing installation

This Mullion harness routes electrical connections through the refrigerator door mullion so lights, sensors and control/LED assemblies communicate with the main cabinet wiring. It restores reliable power and signal routing in the door center strip. What it does:

• Carries power and signal between the door/mullion components and the main harness
• Restores non-functioning mullion lights, LEDs or control communication caused by a damaged harness
• Prevents intermittent connections from frayed or broken mullion wiring
• Used when visible wire damage or connector failure is found in the mullion area

• One (1) mullion harness as pictured

• Disconnect power to the appliance before starting work to avoid shock or injury
• Remove the mullion/door trim and any gaskets per service instructions to access the harness
• Inspect connectors and wire routing; replace any clips or retainers to prevent pinching

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This water connector links sections of the refrigerator's water supply tubing, maintaining a sealed path to the dispenser and ice maker. Replace a cracked or leaking connector to stop drips and restore reliable water flow and ice production.

• Connects sections of internal water tubing between components (inlet valve, filter, door, ice maker)
• Helps maintain a sealed route for proper dispenser and ice maker operation
• Common symptoms: water leaking behind/under the refrigerator, weak/no dispenser flow, ice maker not filling, visible damage at the fitting
• Direct-fit component built to OEM specifications for the intended application

• Unplug the refrigerator and shut off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Cut tubing ends square and fully insert into the connector until seated; tug gently to confirm engagement
• Restore water, check carefully for leaks, and recheck after the first dispense cycle

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head