Parts for Ge CWE23SP2MCS1: Fresh Food Section Parts

Sheet metal screw secures refrigerator panels, trim, and brackets. Replace missing, stripped, or corroded screws to restore proper fit and assembly.

Secures panels, brackets, and trim inside your refrigerator. Replace this 6-22 pan head Phillips screw if the original is stripped, missing, or lost.

Protective cover for refrigerator wire harness connections. Replaces cracked, broken, or missing covers to shield electrical wiring inside your unit.

Fix a non-responsive dispenser or door switch with this refrigerator switch actuator. Restores reliable microswitch engagement when worn or broken.

Freezer thawing or frost building up inside? This defrost thermostat monitors coil temperature during defrost cycles. Easy DIY fix with video guide.

Excess frost in freezer? This evaporator block seal prevents moist air from reaching cold components, reducing frost buildup and improving efficiency.

This holder element assembly secures the appliance's heating element in the correct position so the element stays stable for consistent operation and safe performance. It's a direct-fit replacement for worn or damaged holders. What it does:

• Secures and supports the heating element inside the appliance to maintain proper alignment
• Prevents element sagging or contact with other components that can cause noise or arcing
• Helps reduce vibration and movement that can lead to intermittent heating
• Common symptom: visible holder damage, loose or shifted element, unusual noise during operation

• Disconnect power (unplug or switch off breaker) before starting any repair
• Allow appliance and element to fully cool before handling
• Handle the element and holder carefully to avoid bending or damaging the element

Fixes uneven cooling or frost buildup caused by a misaligned defrost heater. This holder assembly secures the element in place. 15-minute repair.

Hex washer head screw for refrigerators. Secures internal components and panels. Replace if stripped, missing, or damaged during repairs.

This selector control provides the hi/lo switching function for the oven/range heating circuit, restoring user control over high and low heat settings. It replaces a failed selector so the range can select the proper heat level reliably. What it does:

• Switches between high and low heat settings for the heating element or burner
• Restores control when heat setting changes do not respond or stick
• Helps eliminate intermittent or no-heat conditions caused by a worn selector
• Matches OEM function and mounting for a direct replacement

• One selector control assembly as shown

• Disconnect power to the appliance before starting any repair
• Handle electrical connections carefully; note wire locations or take a photo before removal
• Use basic hand tools; do not force connectors or mounting tabs

Adhesive foam gasket that seals gaps between panels and components to reduce air leaks and vibration. Replace when worn or compressed to restore efficiency.

Seals fresh food fan assembly to housing for proper airflow and temperature stability. Replace if damaged to reduce noise and vibration. Confirm fit.

Refrigerator not cooling but freezer works? A failed evaporator fan motor stops cold air circulation. Common DIY repair with video guide available.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Air tower assembly that installs in the fresh food compartment to distribute cold airflow across shelves and bins. Replace if cracked or broken.

This center track screw cover caps the exposed screw on the center track assembly to protect the screw head and give the track a finished appearance. It helps reduce debris buildup and prevents accidental snags on the screw head. What it does:

• Covers and protects the center track screw head from dirt, moisture, and surface wear
• Helps maintain a smooth surface on the track to reduce snagging or catching
• Restores the OEM appearance where the original cap is missing or damaged
• Small replacement part used with center track assemblies and trim pieces

• One center track screw cover (cap)

• Designed for simple push- or snap-fit installation over the exposed screw head
• Remove power to the appliance before accessing internal trim or track areas, and follow manufacturer safety guidance
• If screw or track is damaged, inspect and replace the underlying hardware before installing the cap
• Handle small parts carefully to avoid loss during installation

Refrigerator warm but freezer cold? Your evaporator with heater may be frosted over or leaking. This part cools both compartments and prevents ice buildup.

Fix water pooling in your freezer with a new evaporator drain trough. Channels defrost water away from the freezer compartment to prevent leaks.

This heater harness installs in the refrigerator's fresh food section. It provides defrost heat and the correct wiring connections to clear frost from the fresh food evaporator, restoring airflow so the compartment cools evenly and reliably.

• Delivers defrost heat to the fresh food evaporator to melt frost and ice
• Includes the correct harness/wiring for a precise, plug-in connection
• Helps restore proper airflow and temperature regulation in the refrigerator compartment
• Symptoms include heavy frost on the fresh food evaporator cover or back wall
• Also presents as a warm fridge (with normal freezer) or fan noise from ice contact

• Disconnect power before servicing; use cut-resistant gloves
• Access is behind the fresh food evaporator cover; protect delicate fins and sensors
• Route the harness exactly as the original and fully seat all connectors/clips
• After reassembly, ensure the drain path is clear and the fan spins freely

Fix excessive frost buildup on evaporator coils with this defrost heater. Solves cooling issues and frozen drawers. Moderate DIY repair with video guide.

Fix warm refrigerator sections or inconsistent cooling. This fresh food evaporator cover with deli fan circulates cool air throughout your fridge.

No cold water from dispenser or ice maker? This coiled water tank stores and chills water for dispensing. Fixes leaks from cracked reservoirs.

Dispenser not working or unresponsive? This control assembly operates water and ice dispensing functions. Direct replacement for failed touchpad controls.

No water from dispenser? This tube carries chilled water from valve to spout. Restores flow when original tubing cracks or leaks. Direct fit repair.