Parts for Ge GFSF6KEXCBB: 06 - Fresh Food Section Parts

The water filter is an OEM part for GE refrigerators. This filter removes or reduces various contaminants.

Features and Benefits:

• Easy DIY replacement, typically mounted inside the refrigerator at the back of the compartment.
• Removes or reduces various contaminants in your water and ice, including lead, cysts, asbestos, atrazine, , taste and odor, chlorine, sediment, turbidity, and more
• NSF/ANSI 42 and 53 standards
• 6 Month lifespan filter
• Carbon Block media
• Micron rating: 0.5-1 micron (Class I)

When to replace your filter:

• Bad taste or odor in water and ice
• Cloudy or discolored ice
• Reduced water flow or pressure
• Refrigerator replace filter indicator light is on

Note: If replacing the Culligan metal canister design filter for the first time, a special adapter, part number AP2615702 is needed, which is not included with this part. The compatible bypass cap is part number AP6891551.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This temperature sensor monitors internal refrigerator temperatures and relays them to the control, helping the unit maintain consistent cooling. Replacing a failed sensor restores accurate temperature regulation and more reliable operation. What it does:

• Measures compartment or evaporator temperature and sends a resistance signal to the control board
• Helps the control modulate compressor and fan run times for proper cooling
• Typical failure signs: sections too warm or too cold, erratic temperatures, or running longer than normal
• Causes inaccurate temperature readings compared to setpoints

• 1 temperature sensor assembly

• Disconnect power before servicing
• Access the sensor in the affected section; release any cover/clip and unplug the connector
• Route the new sensor's wiring like the original and ensure it's fully seated in its holder or clip
• Restore power and allow up to 24 hours for temperatures to stabilize

This is a self-tapping screw used to secure appliance panels and small components. It provides a reliable hold in sheet metal and plastic mounting points to restore proper fit and prevent rattling or loose parts. What it does:

• Fastens trim, brackets, and light-duty panels where a tapped hole is needed
• Creates its own threads in thin metal or plastic mounting points
• Helps stop vibration-related noise by securing loose panels
• Commonly used during repairs of control panels, inner liners, and external trim

• One tapping screw as shown

• Use the correctly sized screwdriver or bit to avoid stripping the head
• Drive straight and stop when snug; over-tightening can strip the mating material
• Turn power off and unplug the appliance before accessing internal panels
• If the original hole is damaged or oversized, consider using a slightly larger fastener or repair insert per manufacturer guidance

This damper motor assembly controls the refrigerator air damper to help regulate airflow between compartments, restoring proper temperature balance and reducing uneven cooling when the original motor fails. What it does:

• Moves the air damper to open or close airflow between freezer and fresh-food sections
• Allows the fridge control to direct colder or warmer air as needed for temperature regulation
• A faulty unit can cause symptoms like warm or inconsistent fresh-food temperatures, reduced cooling performance, or unusual clicking/noise at the damper area

• Disconnect power before starting; work on powered appliances can cause shock or injury
• Access typically requires removing interior panels or shelving to reach the damper housing
• Align the motor drive and damper linkage; don't force gears or clips when installing
• After installation, restore power and verify damper movement and temperature control operation

This freezer thermistor is the temperature sensor located in the freezer compartment. It sends temperature feedback to the control so the compressor, fan, and defrost cycle operate correctly, helping maintain consistent freezing performance and stable food storage.

• Monitors actual freezer temperature and changes resistance to signal the control board
• Helps regulate compressor and evaporator fan operation to achieve the set temperature
• Provides input for defrost timing to limit frost buildup and avoid warm swings
• Common failure symptoms: freezer too warm or too cold, temperature fluctuations, long run times, or excessive frost

• Unplug the refrigerator before servicing; work with dry hands and proper lighting
• Access the freezer sensor location; note original orientation and wire routing
• Transfer any mounting clip/holder to the new sensor and seat the connector fully; route wires exactly as original to avoid damage
• Restore power and allow up to 24 hours for temperatures to stabilize

The water filter is an OEM part for GE refrigerators. This filter removes or reduces various contaminants.

Features and Benefits:

• Easy DIY replacement, typically mounted inside the refrigerator at the back of the compartment.
• Removes or reduces various contaminants in your water and ice, including lead, cysts, asbestos, atrazine, , taste and odor, chlorine, sediment, turbidity, and more
• NSF/ANSI 42 and 53 standards
• 6 Month lifespan filter
• Carbon Block media
• Micron rating: 0.5-1 micron (Class I)

When to replace your filter:

• Bad taste or odor in water and ice
• Cloudy or discolored ice
• Reduced water flow or pressure
• Refrigerator replace filter indicator light is on

Note: If replacing the Culligan metal canister design filter for the first time, a special adapter, part number AP2615702 is needed, which is not included with this part. The compatible bypass cap is part number AP6891551.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.