Parts for Ge GTS18GSNDRSS: Fresh Food Section Parts

Fix refrigerator not cooling, lights not working, or display issues with this main control board. Includes LED lights. Requires unplugging and removing screws.

Leveling leg threads into the refrigerator base to support and stabilize the cabinet. Replace if cracked, broken, or worn to keep your unit level.

Supports and pivots your refrigerator door for smooth opening and closing. Replace when door sags, misaligns, or won't seal properly. Confirm fit with your model number before ordering.

Replace your refrigerator's center door hinge to restore smooth door movement and maintain a proper seal. Supports door weight at the pivot point. Confirm fit with your model number before ordering.

Pivot shaft for refrigerator doors at the middle hinge. Replace if worn or bent to restore proper door alignment and smooth operation. Verify fit.

This small replacement corner cap covers and protects an appliance's outer corner trim, restoring a finished look and keeping edges from catching or chipping. It's a simple cosmetic and protective part for worn or broken corner trim. What it does:

• Covers and protects the outer corner of the appliance trim to prevent catches and chips
• Restores a clean, finished appearance where original corner caps are cracked or missing
• Helps keep trim edges aligned and reduces risk of sharp exposed edges
• Common remedy for visible damage after bumps, drops, or long-term wear

• Disconnect power to the appliance before attempting any service that requires removing trim or glass.
• Handle trim and glass carefully—wear gloves and eye protection to avoid cuts from sharp edges.
• This cap typically snaps or fits into place or secures with existing trim hardware; your model's service instructions for removal and reinstallation details.
• If the original trim or mounting clips are damaged, replacement of those items may be required for a secure fit.

Small washer that fits on refrigerator door hinges to distribute weight and reduce friction. Replace if worn, cracked, or missing to restore proper alignment.

Supports the refrigerator door at the lower pivot point for smooth opening and proper sealing. Replace if the door sags or won't close tightly. Confirm fit by model number.

Bottom hinge pin secures the refrigerator door at the base, allowing smooth opening and closing. Replace if worn, damaged, missing, or door sags.

Left front wheel assembly for refrigerators. Installs at the front base to allow smooth rolling. Replace if wheel is cracked, broken, or worn.

Replace a cracked or broken control housing on your top-mount refrigerator. This part secures buttons, knobs, and control boards for proper alignment.

This control shield is a replacement console protector that helps shield the oven/range control assembly from heat, splashes and debris to keep the control area working cleanly. It restores the protective barrier behind the front control surface. What it does:

• Protects the control board and front console from heat, grease and food splatter
• Helps prevent damage that can cause intermittent or unresponsive controls
• Restores proper spacing and support behind the control panel
• Used when the original shield is warped, cracked or missing

• One control shield

• Disconnect power (unplug or switch off breaker) before starting any repair
• Remove the control panel or console trim per service instructions to access the shield
• Replace with matching orientation and secure using the original screws/clips; do not force or bend the part

Fix interior lights that won't turn on, stay on constantly, or delay when opening the door. This switch replacement takes 10-15 minutes with basic tools.

This genuine fastener secures appliance components such as panels and brackets. Replacing a missing or stripped screw restores proper fit and helps reduce vibration or rattling. Features 12-24 threads and an approximate 0.785-inch length. What it does:

• Fastens panels, brackets, covers, and other hardware points in the appliance
• Helps maintain proper alignment and a tight fit of components
• Replaces damaged, stripped, or missing hardware
• Common symptoms include loose or rattling parts and hardware that won't tighten

• One screw

• Disconnect power before servicing; shut off water supply if working near water components
• Start the screw by hand to avoid cross-threading; replace one-for-one in the original location
• Use the correct driver bit for the head style; tighten snugly without overtightening into plastic or thin metal