Parts for Ge PDCE1NBWCDSS: 04 - Fresh Food Section Parts

This replacement air tower assembly is the vertical duct that channels chilled air through the refrigerator compartment. Replacing a damaged tower restores proper airflow to help maintain even temperatures and consistent cooling from top to bottom.

• Directs cold air from the evaporator to vents in the fresh food section
• Helps balance temperatures and reduce warm spots
• Often replaced when the original is cracked, broken, or warped
• Common symptoms: weak airflow from refrigerator vents and uneven cooling in the fresh food compartment

• Disconnect power to the refrigerator before servicing.
• Remove shelves and bins for access; release tabs or remove screws securing the old tower.
• Transfer any clips or sensors from the original, if present; seat and secure the new tower.
• Restore power and verify airflow from the vents.

The Temperature Sensor Seal is an OEM part for GE refrigerators. This seal is designed to protect the temperature sensor from moisture and other environmental factors that could affect its accuracy and longevity. By providing a barrier against the harsh conditions within a refrigerator, such as humidity and temperature fluctuations, this seal ensures that the sensor can accurately monitor and control the refrigerator's internal temperature.

Causes of a malfunctioning Temperature Sensor Seal can include wear and tear over time, degrading the seal's effectiveness. Physical damage like tears or punctures can allow moisture to reach the sensor. Improper installation may leave gaps or loose areas around the sensor, compromising the seal.

Symptoms of a bad Temperature Sensor Seal include:

• Inaccurate temperature readings.
• Condensation or frost near the sensor location.
• Frequent cycling or unusual patterns in the refrigerator's cooling process.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Temperature Sensor Grille is an OEM part for GE refrigerators. This grille covers and protects the temperature sensor, ensuring it accurately measures the internal temperature of the refrigerator.  

Causes of a bad grille can include physical damage from impacts, regular wear and tear, or the buildup of dust and debris that can obstruct airflow.  

Symptoms of a bad temperature sensor grille include:

• Inaccurate temperature readings
• The refrigerator running continuously or not cooling properly
• Visible damage or obstruction on the grille
• The sensor becoming loose or dislodged

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Bulb Light is an OEM part for GE refrigerators. It is designed to illuminate the interior of the refrigerator and freezer compartments, making it easier to see and access food items. This light bulb fits securely into the designated socket and provides bright, reliable lighting to enhance visibility.

You should replace the bulb light if it burns out or becomes damaged. Causes of a bad bulb light can include regular wear and tear, electrical issues, or physical damage from impacts or vibrations. A faulty bulb can leave the refrigerator compartments dim or completely dark, making it difficult to find items.

Symptoms of a bad bulb light include:

• The light not turning on when the refrigerator door is opened
• Flickering or intermittent lighting
• A visibly burned-out or broken bulb

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This light shield is the clear cover over the fresh food compartment light. It diffuses brightness and protects the bulb or LED from bumps, restoring even illumination and a finished look inside your refrigerator.

• Covers and protects the fresh food compartment light assembly
• Diffuses light to reduce glare and hot spots
• Replaces a cracked, yellowed, loose, or missing light cover/lens
• Helps the lens stay secured when original tabs are broken

What's included: One light shield for the fresh food compartment. Install notes:

• Unplug the refrigerator or switch off power before service
• Allow the lamp to cool; remove shelves for access if needed
• Release retaining tabs or hardware, noting the shield's orientation
• Seat the new shield fully; avoid forcing tabs or overtightening hardware

This vertical vent duct is a direct-replacement exhaust channel that routes hot, moist air from the appliance to the home vent, helping maintain proper airflow and reduce moisture or heat buildup around the unit. What it does

• Channels exhaust air from the appliance to the household vent line.
• Helps prevent exhaust air from leaking into the room and reduces backflow.
• Common symptoms it can address: long drying cycles, excess humidity or heat near the appliance, and visible exhaust escaping into the room.
• Fits into the appliance's existing vent connection to restore correct airflow.

• Turn off and disconnect power (and gas, if applicable) before servicing.
• Verify the existing vent path is clear and the duct orientation matches appliance connections.
• Use basic hand tools; avoid crushing or kinking the duct during installation.

This vertical vent duct directs internal airflow inside the cabinet to help maintain consistent temperatures and proper circulation. It replaces a cracked, warped or missing duct to restore designed airflow paths and reduce uneven cooling. What it does:

• Channels cold air between compartments to support even cooling and freezing
• Prevents air leaks that can cause warm spots or extra run time
• Helps maintain proper defrost and frost patterns when installed correctly
• Reduces noise from rattling or vibrating panels if damaged ducts are secured

• Disconnect power to the appliance before starting any repair
• Remove shelves, panels or evaporator cover as needed to access the old duct
• Inspect adjacent seals and fasteners; replace damaged clips or gaskets for best fit
• Reassemble panels securely and test operation; for model-specific instructions

This replacement air tower assembly is the vertical duct that channels chilled air through the refrigerator compartment. Replacing a damaged tower restores proper airflow to help maintain even temperatures and consistent cooling from top to bottom.

• Directs cold air from the evaporator to vents in the fresh food section
• Helps balance temperatures and reduce warm spots
• Often replaced when the original is cracked, broken, or warped
• Common symptoms: weak airflow from refrigerator vents and uneven cooling in the fresh food compartment

• Disconnect power to the refrigerator before servicing.
• Remove shelves and bins for access; release tabs or remove screws securing the old tower.
• Transfer any clips or sensors from the original, if present; seat and secure the new tower.
• Restore power and verify airflow from the vents.

The Temperature Sensor is an OEM replacement part for GE refrigerators, designed to accurately monitor and relay the temperature inside the refrigerator and freezer compartments to the electronic control board. By detecting the slightest changes in internal temperature, the sensor allows the control board to make real-time adjustments to the cooling system, activating the compressor and fans as needed to maintain optimal conditions for food preservation.

Over time, the temperature sensor can fail due to electrical issues, exposure to moisture, or general wear and tear. A malfunctioning sensor can lead to improper temperature regulation, affecting the efficiency of the refrigerator and the freshness of stored food.

Symptoms of a bad Temperature Sensor include:

• The refrigerator or freezer not maintaining the set temperature 
• The appliance running continuously or more frequently than normal
• Inaccurate temperature readings displayed  

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

This refrigerator temperature control board regulates cooling by reading sensor inputs and directing the compressor, fans, and defrost cycle. Replacing a failed board helps restore accurate temperatures and responsive controls.

• Monitors temperature sensors and maintains set points
• Controls the compressor, fans, and defrost cycle as designed
• Interfaces with the temperature buttons/display where equipped
• A failing board can cause drifting temps or no cooling, unresponsive controls, or intermittent cycling

• Disconnect power before servicing and verify no voltage is present
• Use ESD protection; handle the board by the edges only
• Photograph wiring; move keyed connectors one at a time and seat fully
• After installation, restore power and allow up to 24 hours for temperatures to stabilize; follow any model-specific setup on the service sheet