Parts for Ge GTE18ITHPRBB: Fresh Food Section Parts

Vegetable pan support bracket for top-mount refrigerators. Installs inside the crisper drawer compartment. Replace if cracked, broken, or missing.

Fastens panels, brackets, and trim to appliance cabinets. Replace this screw when the original is missing, stripped, or damaged during service work.

Refrigerator not cooling or ice building up on evaporator coils? The defrost timer controls the defrost cycle. DIY-friendly, installs in 5 minutes.

Leveling leg threads into the refrigerator base to support and stabilize the cabinet. Replace if cracked, broken, or worn to keep your unit level.

Secures and guides your refrigerator door for smooth operation. Replace when door sags, misaligns, or fails to seal properly. Confirm fit with your model.

Replace your refrigerator's center door hinge to restore smooth door movement and maintain a proper seal. Supports door weight at the pivot point. Confirm fit with your model number before ordering.

Pivot shaft for refrigerator doors at the middle hinge. Replace if worn or bent to restore proper door alignment and smooth operation. Verify fit.

Small washer that fits on refrigerator door hinges to distribute weight and reduce friction. Replace if worn, cracked, or missing to restore proper alignment.

Supports the refrigerator door at the lower pivot point for smooth opening and proper sealing. Replace if the door sags or won't close tightly. Confirm fit by model number.

Bottom hinge pin secures the refrigerator door at the base, allowing smooth opening and closing. Replace if worn, damaged, missing, or door sags.

Front left wheel assembly for top-mount refrigerators. Replaces broken or worn mobility wheels that allow your refrigerator to roll smoothly for cleaning.

Replace the right front wheel assembly on your top-mount refrigerator. Needed when the wheel is cracked, broken, or worn, causing mobility issues.

Protective cover for the icemaker receptacle in your freezer compartment. Prevents moisture from entering the socket when an icemaker is not installed.

Replaces a worn, cracked, or missing temperature control knob on your refrigerator. Installs on the control panel for secure grip and smooth adjustments.

Fridge warm but freezer cold? This temperature control thermostat monitors compartment temp and cycles the cooling system. DIY repair with video guide.

This nozzle control foam is a soft sealing pad that fits around the refrigerator dispenser nozzle to help cushion the nozzle and maintain a tight seal at the dispenser opening. It keeps the dispenser area neater and helps reduce splashes and drafts. What it does:

• Seals the gap around the dispenser nozzle to limit water drips and air infiltration
• Cushions and stabilizes the nozzle to reduce movement and wear
• Helps keep the dispenser opening cleaner by blocking debris entry
• Can reduce minor splatter and improve dispenser appearance

• Disconnect power and shut off the water supply before servicing the dispenser area
• Remove the dispenser bezel or outer trim to access the nozzle per your model's service instructions
• Press the foam into the nozzle cavity until it seats evenly; do not stretch or tear the foam
• Use only manufacturer-approved fasteners or clips; avoid adhesives unless your service manual specifies

Fix refrigerator drawers that slam shut or stick when opening. This drawer glide wheel damper restores smooth, controlled movement. Easy 10-minute fix.

Foam insulation block that installs around the refrigerator control housing. Replace if cracked, compressed, deteriorated, or missing to restore insulation.

Spacer component that fits on the temperature control shaft inside your refrigerator. Replace if the original is cracked, worn, or missing.

Fix a slamming or misaligned refrigerator door with a new hinge damper shaft. Restores smooth, quiet closing and proper door alignment in minutes.

Push-on spring knob for refrigerator control shafts. Replaces worn, cracked, or missing knobs to restore secure grip and smooth operation of controls.

Replace your refrigerator's light shield reflector to restore proper interior lighting. This lens cover protects the bulb and directs light effectively. Confirm fit with your model number.

Interior light not working when door opens? This light switch controls refrigerator illumination. DIY-friendly install takes 30-45 minutes with video.

This genuine fastener secures appliance components such as panels and brackets. Replacing a missing or stripped screw restores proper fit and helps reduce vibration or rattling. Features 12-24 threads and an approximate 0.785-inch length. What it does:

• Fastens panels, brackets, covers, and other hardware points in the appliance
• Helps maintain proper alignment and a tight fit of components
• Replaces damaged, stripped, or missing hardware
• Common symptoms include loose or rattling parts and hardware that won't tighten

• One screw

• Disconnect power before servicing; shut off water supply if working near water components
• Start the screw by hand to avoid cross-threading; replace one-for-one in the original location
• Use the correct driver bit for the head style; tighten snugly without overtightening into plastic or thin metal