Parts for Ge GTE21GTHFBB: Fresh Food Section Parts

This left top hinge supports and pivots the refrigerator's left door at the top, keeping it aligned for smooth opening and a tight seal. Replace a worn or bent hinge to restore proper door movement and closing.

• Supports the left refrigerator door at the top pivot point
• Maintains alignment so the door closes and seals correctly
• Provides a smooth pivot for consistent opening and closing
• Typical symptoms of a failing hinge: sagging or misaligned door, rubbing/binding at the top, creaking/clicking noises, or poor gasket contact

• Disconnect power and remove items from the door before service.
• Have a second person support the door while removing the hinge screws.
• Mark the original alignment and transfer any shims; install the new hinge and tighten screws securely.
• Check door swing and gasket contact all around; adjust as needed.

This genuine replacement screw secures components and trim on compatible appliances, restoring proper fit and preventing loose parts. Use it to replace a lost or stripped fastener and keep panels and assemblies stable. What it does:

• Fastens trim, panels, brackets or internal components to the appliance chassis
• Restores secure attachment where a damaged or missing screw causes rattling or loose parts
• Helps maintain proper alignment of doors, panels or control assemblies
• Small, corrosion-resistant design for reliable long-term fastening

• Use the matching driver bit to avoid stripping the head; hand-start threads before using a driver
• Do not overtighten—stop when the part is snug and secure to avoid cracking panels or stripping threads
• Disconnect power and follow appliance-specific safety steps before accessing internal components
• If original hardware shows corrosion or thread damage, replace with the correct OEM fastener only

A right-hand hinge top and pin assembly that restores proper refrigerator door alignment and secure top-hinge support. Replaces worn or damaged hinge components to help the door open and close smoothly. What it does:

• Provides upper hinge support and a pivot pin for the door
• Corrects door sag, uneven gaps, or doors that don't latch fully
• Reduces rubbing, binding, or noisy hinge operation
• Restores stable door movement after hinge wear or damage

• Unplug the appliance or switch off power before starting any repair
• Remove food and shelves near the door; have a helper support the door during removal/installation
• Use proper hand tools and follow the washer/fastener torque from the manufacturer; do not overtighten
• Inspect surrounding hinges and strike for wear; test door alignment after installation

A small plastic push-in retainer used to secure interior trim, panels, or components on appliances. Replaces broken or missing rivets to restore a snug, rattle-free fit and keep parts aligned. What it does:

• Holds trim, panels or lightweight components in place by expanding after insertion
• Prevents rattling and gaps caused by loose or missing fasteners
• Keeps decorative and protective pieces aligned for a finished appearance
• Suitable for common non-structural fastening needs on appliances

• One plastic push-in rivet

• Unplug or disconnect power to the appliance before beginning any service
• Remove the panel or trim piece as needed to access the rivet location; a trim removal tool or small flat screwdriver often helps
• Push the rivet into the hole until the head is flush; some designs require depressing the center pin to lock
• Replace any damaged rivets with the same size and style to ensure a secure fit

This middle hinge washer is the small pivot spacer used on the refrigerator door middle hinge to reduce friction and ensure smooth door movement. Replaces a worn or missing washer to help doors align and operate quietly. What it does

• Acts as a spacer and bearing surface on the middle door hinge to reduce metal-on-metal wear and friction.
• Helps maintain proper door alignment and consistent opening/closing action.
• Commonly linked to symptoms like a noisy, stiff, or misaligned refrigerator door.

• One middle hinge washer.

• Install with power off and door supported; remove or prop the door per your model's service instructions to avoid injury or damage.
• Verify correct orientation and seating on the hinge pin before reassembling; do not force parts.
• Use only manufacturer-recommended parts; if other hinge hardware is damaged, replace that hardware as needed.

A center hinge for a refrigerator door that supports and pivoting point to keep the door aligned for proper sealing and smooth operation. Replacing a damaged center hinge can restore correct door fit and reduce rubbing or gaps. What it does:

• Supports the door weight and provides the central pivot point for opening and closing
• Keeps the door aligned so the gasket seals evenly along the cabinet
• Helps prevent door sag, uneven gaps, and door-to-cabinet rubbing
• Works with hinge pins and mounting hardware to maintain smooth door movement

• Disconnect power to the appliance before starting any repair
• Support the door securely before removing hinge fasteners to prevent injury or damage
• Keep original fasteners and mounting hardware; replace any stripped or damaged screws
• After installation, check door alignment and adjust adjacent hinges as needed for a proper seal

This replacement door switch restores proper door sensing so your refrigerator's interior lights turn on when the door opens and shut off when it closes, helping prevent warm spots and nuisance door-ajar alerts.

• Spring-loaded plunger detects the door's open/closed position
• Switches power to the interior lights; on many models also signals door-ajar or fan interlock functions
• Helps prevent lights from staying on and heating the compartment
• Typical failure signs: lights won't turn on, lights stay on, or door-ajar warnings with the door closed

• Disconnect power to the refrigerator before servicing
• Carefully pry the old switch straight out of the liner or remove its mounting screws, as applicable
• Move wires to the new switch one at a time to keep connections correct
• Seat the new switch fully; verify the plunger moves freely and lights operate before closing up

Electronic defrost control board that manages the refrigerator's timed defrost cycles to reduce evaporator frost buildup and help maintain steady cooling. Replacing a failed control restores normal automatic defrost operation. What it does:

• Regulates defrost cycle timing and duration to prevent excessive ice on the evaporator
• Stops regular cooling temporarily during defrost to melt accumulated frost
• Common symptom: excessive frost or ice buildup on evaporator coils or in the freezer compartment
• Other symptom: temperature fluctuations or the unit running continuously because defrost cycles aren't happening

• Always disconnect power to the appliance before servicing to avoid electrical shock
• Access typically requires removing the refrigerator's control or back access panel — keep screws and small parts organized
• Match wire harness connectors and mounting holes; do not force connectors or bend pins

Replace a worn or broken control knob so you can reliably adjust your appliance's settings again. This knob attaches to the control shaft and restores smooth turning and a clean, factory look.

• Attaches to the control shaft so you can turn and set the control accurately
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps when the knob spins freely, won't stay on, or settings won't adjust
• Restores proper grip and appearance of the control panel

• Disconnect power to the appliance before servicing
• Pull the old knob straight off the shaft; avoid prying to prevent damage
• Align the shaft orientation on the new knob and press it on until fully seated
• Verify smooth operation after installation

A replacement lamp cover that protects the oven/microwave light and helps diffuse interior lighting for safer, easier viewing. Restores light appearance and prevents direct contact with the bulb. What it does:

• Covers and protects the interior lamp from food, steam and debris
• Diffuses and softens the bulb's light for more even interior illumination
• Prevents accidental contact with the hot bulb or glass
• Common symptom: cracked, chipped or discolored lens that reduces light or looks damaged

• One replacement lamp cover

• Disconnect power or unplug the appliance before starting any work
• Allow the bulb to cool completely before removing the old cover
• Handle the cover carefully; use gloves to avoid cuts or fingerprints on clear surfaces
• If the cover snaps or screws in place, align clips or threads and secure without overtightening

This replacement lamp restores bright, reliable lighting inside your refrigerator or freezer so you can easily see contents whenever the door opens. Swap a burned-out bulb to bring back full visibility and everyday convenience. What it does:

• Provides illumination inside the fresh food or freezer compartment when the door switch is activated
• Replace if the light won't turn on, flickers, appears dim, or the bulb glass is darkened/broken
• Helps you quickly find items and spot spills or leaks
• If lighting issues persist after replacement, inspect the door switch, socket, or wiring

• 1 replacement lamp

• Disconnect power to the refrigerator before servicing
• Allow the old bulb to cool; handle glass with gloves or a cloth
• Install the bulb straight into the socket; do not overtighten or force
• Use only the bulb type and wattage specified for your model; do not exceed the rating

The Bottom Hinge is an OEM component specifically designed for GE refrigerators. It acts as the main pivot point that allows the door to smoothly and reliably open and close.  

The bottom hinge supports the entire weight of the refrigerator door during use. It is responsible for providing smooth, controlled movement without sagging or binding over extended periods.

Causes of a bad bottom hinge can include looseness from wear of the metal pins and sleeves over thousands of door openings. Damage is also possible from unintended heavy impacts on the door over time.

Symptoms of a bad bottom hinge include:

• The door not sitting level or sagging slightly open  
• Increased effort required to open or close 
• Scraping or grinding noises coming from the hinge area
• The door is unable to stay fully closed without assistance

This authentic GE replacement part is also compatible with Hotpoint, RCA, and select Kenmore models.

This wheel adjust foot replaces a worn or damaged leveling glide to restore stable, even support and easy adjustment for the appliance. It helps keep the appliance level and prevents rocking or uneven wear. What it does

• Provides an adjustable contact point for leveling the appliance on uneven floors.
• Restores smooth height adjustment so doors and drawers align properly.
• Reduces rocking, vibration, and movement during operation.
• Helps prevent premature wear on cabinet corners and floor surface.

• One wheel adjust foot

• Turn off and unplug the appliance before attempting any repair or adjustment.
• Use proper tools to remove the old foot and thread the replacement in by hand; do not overtighten.
• Place appliance on a stable surface and re-check level after installation; adjust as needed.

This is a single mounting screw used to secure components and panels on compatible GE appliances. It provides a reliable fastener for replacing lost or damaged screws to restore proper fit and reduce rattling or loose parts. What it does:

• Secures panels, brackets, or small components to the appliance frame
• Restores proper panel fit and alignment to reduce vibration and noise
• Helps maintain grounding and stable connections where a screw fastens an electrical or chassis part
• Replaces missing or stripped screws that prevent panels or assemblies from seating correctly

• Unplug the appliance or shut off power at the circuit breaker before starting
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid overtightening which can strip threads or crack components
• Replace with the exact part number for best fit and function

This is the temperature control thermostat for a refrigerator. It senses compartment temperature and opens/closes the circuit to the compressor and fans, maintaining your set temperature and helping correct cooling that's too warm, too cold, or inconsistent. What it does

• Monitors compartment temperature and cycles cooling on and off to hold the selected setting
• Restores proper cycling when a unit runs constantly or will not turn on
• Common symptoms include temperatures not responding to dial changes, food freezing in fresh food section, or no "click" at the Off position
• Helps when cooling is intermittent or the refrigerator short-cycles

• One temperature control thermostat

• Disconnect power before servicing
• Note/photograph wire positions and transfer one at a time
• Route the sensing bulb/capillary in the original path; avoid kinks or sharp bends
• Set to a mid setting, restore power, and allow up to 24 hours for temperatures to stabilize