Parts for Ge GTS18FSLCSS: Fresh Food Section Parts

This top hinge secures the upper edge of the appliance door to the cabinet, providing stable door pivoting and proper alignment for smooth opening and closing. Replacement hinge restores correct door fit and function. What it does:

• Attaches the top of the door to the cabinet and provides the pivot point for opening and closing
• Helps maintain proper door alignment and seal for efficient operation
• Worn or bent hinges can cause the door to sag, bind, or not close fully
• Replacing a damaged hinge can reduce door play and restore normal movement

• Disconnect power and empty the door area before starting repairs for safety
• Support the door while removing the old hinge to prevent damage or injury
• Typical installation requires basic hand tools (screwdriver/socket) and aligning the door during reassembly

This center hinge shim is a small alignment spacer that helps position and level the refrigerator door hinge for smoother door operation and even door spacing. It restores proper door alignment without replacing hinge assemblies. What it does:

• Centers and spaces the middle door hinge to correct uneven gaps or rubbing
• Helps doors close evenly and reduces binding or misalignment
• Restores proper door tilt for consistent gasket sealing and cooling
• Works when a thin spacer is needed between hinge components

• Typically installed between hinge components with basic hand tools; your model's service instructions
• Remove power to the appliance before disassembling hinge hardware to avoid injury
• Keep small parts, shims, and fasteners secure during reassembly
• If hinge or mounting hardware is damaged or bent, replace those components as well for a proper repair

This washer hinge pin secures the lid/door to the washer cabinet, restoring proper alignment and smooth opening/closing. Replacing a worn or damaged hinge pin helps stop sagging lids and prevents uneven wear on the hinge assembly. What it does:

• Anchors the lid/door to the hinge assembly so the door pivots correctly
• Keeps the lid aligned to prevent rubbing, catching, or uneven gaps
• Stops or reduces sagging, wobbling, or misaligned door movement
• Helps eliminate noise or binding caused by a loose or worn hinge

• One (1) washer hinge pin

• Disconnect power (unplug the washer) before starting any repair
• Support the lid/door while removing the old pin to prevent dropping or damage
• Use basic hand tools; inspect hinge and surrounding parts for wear and replace if needed

This center hinge pin secures the refrigerator door hinge assembly and provides a stable pivot for smooth door movement and alignment. Replaces a worn or damaged pin to help restore proper door swing and closing. What it does

• Serves as the pivot point for the center/door hinge, keeping the door aligned on the cabinet.
• Helps eliminate door sag, misalignment, or uneven gaps caused by a worn hinge pin.
• Reduces squeaking or binding at the hinge when the pivot is damaged or corroded.
• Works with the hinge assembly to maintain smooth opening and closing of the door.

• One center hinge pin.

• Unplug the appliance or shut off power to avoid electrical hazards before starting work.
• Support the door while removing the hinge assembly to prevent injury or damage.
• Use appropriate hand tools; avoid forcing parts—inspect hinge and surrounding components for wear.

This unpainted center hinge replaces the worn or damaged hinge that supports and aligns the refrigerator door. Restores correct door positioning and helps reduce sagging, rubbing, or uneven closing for smoother operation. What it does:

• Supports the refrigerator door at the center pivot point to maintain proper alignment
• Keeps the door level to prevent scraping, gaps, and uneven seals
• Helps restore smooth opening and closing and reduces hinge-related noise
• Prevents extra strain on adjacent hinges and door components

• Disconnect power and empty or secure the door before removing or installing hinges.
• Removal/installation typically requires hand tools; follow OEM instructions for door support and alignment.
• Handle edges carefully to avoid injury; paint or finish as needed to match appliance aesthetics.

This adaptive defrost control module manages a refrigerator's defrost cycles to reduce unnecessary defrosting and help maintain proper cooling performance. It replaces the original control board that times and initiates defrost events. What it does:

• Monitors fridge activity and initiates defrost cycles based on usage patterns to avoid excess frost buildup
• Controls the defrost heater and terminates defrost when appropriate to protect the evaporator
• Can prevent frequent or missed defrosts that lead to frost-covered evaporator coils
• Commonly replaced when the freezer or refrigerator shows repeated frosting, long run-times, or inconsistent cooling

• Disconnect power to the appliance before starting any repair to avoid shock or damage
• Replace the module in the control housing; handle the board carefully to avoid static damage
• Verify wiring matches the original and secure all connectors; note orientation before removal
• Restore power and observe a few cycles to confirm the unit is initiating/terminating defrosts correctly

This temperature control is the thermostat that monitors refrigerator temps and cycles cooling components to maintain the selected setpoint. Replacing a faulty control helps restore consistent cooling and prevents temperature swings that risk food spoilage. What it does

• Senses interior temperature and sends signals to the compressor and fans to start or stop as needed.
• Regulates cycling to maintain the user-set temperature and prevent over- or under-cooling.
• Common symptom indicator: erratic temperatures, fridge running constantly, or compressor not cycling.
• Works as the control interface between the thermostat sensor and the cooling system components.

• Disconnect power to the appliance before attempting any service to avoid shock or damage.
• Handle electronic components and wiring gently; unplug connectors by the plug, not the wires.
• Access may require removing the control housing or rear cover.

This refrigerator shelf pad cushions and protects a glass shelf while helping keep items steady. It's an easy replacement that restores a non-slip surface and reduces vibration between dishes and the shelf. What it does:

• Provides a non-slip surface to help keep dishes and containers from sliding
• Cushions items to reduce rattling and chipping on glass shelves
• Protects the shelf from scratches and minor impacts
• Useful when the original pad is torn, warped, missing, or worn smooth

• One refrigerator shelf pad

• Place the pad directly onto a clean, dry glass shelf—no tools required
• Wipe the shelf clean of debris and moisture before installing for best adhesion and fit
• Verify correct placement so the pad lies flat and does not interfere with shelf slides
• If torn or deformed, replace the pad before storing heavy or fragile items

This LED bulb replaces a dim or burned-out interior appliance light, restoring clear, energy-efficient illumination inside refrigerators and similar units. It provides long-lasting, cool light to help you see contents more easily. What it does:

• Replaces a failed or dim interior light bulb to restore visibility inside the appliance
• Uses LED technology for efficient, longer-lasting illumination compared with incandescent bulbs
• Produces cool light that reduces heat inside the appliance compartment
• Designed to match the fit and function of the original equipment bulb in compatible units

• Disconnect power to the appliance before installing to avoid shock
• Allow the old bulb to cool before handling; remove by unscrewing from the light socket
• Install the LED bulb by screwing into the socket until snug; do not overtighten
• Restore power and verify the new bulb lights; if it does not, recheck the connection and power